Check the radio automatic station search function by activating it.
Automatic station search function stops on a station.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
Optional components are installed.
Do not remove optional components without the permission of the customer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna connector from the radio receiver assembly.
Turn the engine switch on (ACC) with the radio receiver assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.
Noise can be heard from the speakers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the RA radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (ANT+) - Body ground | Engine switch on (ACC), radio switch on and FM or AM selected | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Remove the antenna connector from the radio receiver assembly.
Remove the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| RA-3 (MAIN) - 2 | Always | Below 1 Ω |
| RA-5 (ANT+) - 3 | Always | Below 1 Ω |
| RA-3 (MAIN) - Body ground | Always | 10 kΩ or higher |
| RA-5 (ANT+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
Remove the antenna connector from the antenna cord sub-assembly.
Remove the antenna connector from the No. 3 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 2 | Always | Below 1 Ω |
| 3 - 3 | Always | Below 1 Ω |
| 2 - Body ground | Always | 10 kΩ or higher |
| 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to No. 1 Antenna Amplifier Assembly) |
Remove the antenna connector from the No. 2 antenna cord sub-assembly.
Remove the antenna connector from the No. 1 antenna amplifier assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 2 | Always | Below 1 Ω |
| 3 - 1 | Always | Below 1 Ω |
| 2 - Body ground | Always | 10 kΩ or higher |
| 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG