The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door disassembly/reassembly are shown below.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
Fully open the rear door glass sub-assembly LH before proceeding with work.
1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67674A
3.REMOVE REAR DOOR FRAME GARNISH LH
Detach the clip and claw and remove the rear door frame garnish LH.
74260
4.REMOVE REAR ARMREST ASSEMBLY LH
|
Order of Removal |
|
Remove in this Direction |
Detach the clip and claw and remove the rear armrest assembly LH.
5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
|
Remove in this Direction |
Detach the clip and claw.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
84810D
6.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
81230
7.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
67666C
8.REMOVE REAR DOOR TRIM REFLECTOR LH (w/ Reflex Reflector Assembly)
| *A | for LH side |
| *B | for RH side |
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Put protective tape around the reflex reflector.
Using a thin-bladed screwdriver, detach the claw and guide.
Tape the thin-bladed screwdriver tip before use.
Remove the rear door trim reflector LH.
69284D
9.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH
Using moulding remover A, detach the claw and remove the rear door inside handle bezel plug LH as shown in the illustration.
67604
10.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
|
Place Hands Here |
|
Order of Removal (1) |
|
Order of Removal (2) |
|
Remove in this Direction |
Detach the clip as shown in the illustration.
|
Remove in this Direction |
Detach the guide and remove the rear door trim board sub-assembly LH as shown in the illustration.
| *1 | Rear Door Inside Looking Cable Assembly LH |
| *2 | Rear Door Lock Remote Control Cable Assembly LH |
|
Remove in this Direction |
Detach the clamp and disconnect the rear door lock remote control cable assembly LH and rear door inside looking cable assembly LH as shown in the illustration.
69206C
11.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH
|
Remove in this Direction |
Detach the claw and guide and remove the rear door inside handle sub-assembly LH.
68174A
12.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
|
Remove in this Direction |
Raise the claw of the rear door inner glass weatherstrip LH as shown in the illustration, and then remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH.
86160B
13.REMOVE REAR SPEAKER ASSEMBLY
67842E
14.REMOVE REAR DOOR SERVICE HOLE COVER LH
|
Butyl Tape |
Pull out the rear door lock remote control cable assembly LH, rear door inside locking cable assembly LH and wire harness from the rear door service hole cover LH, and then remove the rear door service hole cover LH.
Remove any remaining butyl tape from the rear door panel.
15.REMOVE SCREW GROMMET
Using a clip remover, detach the claw and remove the 2 screw grommets.
68152C
16.REMOVE REAR DOOR GLASS RUN LH
Detach the guide and remove the rear door glass run LH.
67408E
17.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
|
Bolt |
|
Screw |
Lift up the rear door weatherstrip LH and remove the screw.
Remove the 2 bolts and rear door window division bar sub-assembly LH.
68104
18.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the rear door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.
Be careful not to damage the glass.
68124C
19.REMOVE REAR DOOR QUARTER WINDOW GLASS LH
|
Remove in this Direction |
Remove the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH.
68189
20.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
Remove the rear door quarter window weatherstrip LH from the rear door quarter window glass LH.
75724
21.REMOVE REAR DOOR REAR BELT MOULDING LH
75740
22.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH
69804
23.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
|
Bolt |
|
Connector |
|
Temporarily Bolt |
Disconnect the connector.
Loosen the temporarily bolt.
Do not remove the temporarily bolt. If the temporarily bolt is removed, the rear door window regulator sub-assembly LH may fall and become damaged.
Remove the 4 bolts and rear door window regulator sub-assembly LH.
85720G
24.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
67836H
25.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH
Remove the rear door lock child protection cover LH.
69340
26.REMOVE REAR DOOR LOCK ASSEMBLY LH
69038A
27.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY LH
69740D
28.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
69780B
29.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
69318D
30.REMOVE DOOR LOCK WIRING HARNESS SEAL
69227M
31.REMOVE REAR DOOR OUTSIDE HANDLE COVER
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the claw and remove the rear door outside handle cover as shown in the illustration.
69240
32.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
|
Remove in this Direction |
Remove the rear door outside handle assembly LH as shown in the illustration.
69241G
33.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
|
Remove in this Direction |
Detach the claw and remove the rear door front outside handle pad.
69242G
34.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
|
Remove in this Direction |
Detach the claw and remove the rear door rear outside handle pad.
69204A
35.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
| *a | Grommet |
| *b | Guide |
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the grommet and guide and remove the rear door outside handle frame sub-assembly LH.
67003C
36.REMOVE REAR DOOR PANEL CUSHION
Detach the claw and remove the 2 rear door panel cushions.
68640A
37.REMOVE REAR DOOR CHECK ASSEMBLY LH
|
Bolt (A) |
|
Bolt (B) |
Remove the 2 bolts (A), bolt (B) and rear door check assembly LH.
67872
38.REMOVE REAR DOOR WEATHERSTRIP LH
|
Double-sided Tape |
Using a clip remover, detach the clip and remove the rear door weatherstrip LH.
Remove any remaining double-sided tape from the rear door panel LH.
67837C
39.REMOVE REAR DOOR DUST PROOF SEAL
Detach the claw and remove the 3 rear door dust proof seals.
75924C
40.REMOVE NO. 2 BLACK OUT TAPE LH
75926C
41.REMOVE NO. 3 BLACK OUT TAPE LH