When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
44763C
1.REMOVE NO. 2 HOSE TO HOSE TUBE
Slide the clamp and disconnect the union to check valve hose from the vacuum pump assembly.
Remove the 2 bolts and No. 2 hose to hose tube from the cylinder head cover sub-assembly and hose bracket.
12632
2.REMOVE NO. 2 ENGINE COVER BRACKET
82121
3.REMOVE ENGINE WIRE
17363K
4.REMOVE INTERCOOLER AIR TUBE
26100G
5.REMOVE DIESEL THROTTLE BODY ASSEMBLY
16278
6.REMOVE NO. 2 WATER BY-PASS PIPE
89481B
7.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
89425
8.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
25733A
9.REMOVE NO. 1 VACUUM PIPE (w/ DPF)
25734
10.REMOVE NO. 2 VACUUM PIPE (w/ DPF)
17578B
11.REMOVE PIPE CLAMP (w/ DPF)
12631A
12.REMOVE ENGINE COVER BRACKET
Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.
23265C
13.REMOVE GAS FILTER
89421C
14.REMOVE DIESEL TURBO PRESSURE SENSOR
25625
15.REMOVE EGR VALVE BRACKET
25612
16.REMOVE NO. 2 EGR PIPE
16206B
17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
25601
18.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
except i-ART:
Disconnect the connector from the common rail assembly.
Detach the 2 clamps and remove the connecting wire from the hose bracket.
Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.
Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
25804
19.REMOVE VACUUM CONTROL VALVE SET
16209
20.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
| *1 | No. 6 Water By-pass Hose |
| *2 | No. 7 Water By-pass Hose |
| *3 | Water Hose |
Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.
Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.
25800
21.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
11409
22.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23812D
23.REMOVE NO. 2 FUEL PIPE
Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.
Remove the bolt and No. 2 fuel pipe from the manifold stay.
24.REMOVE WIRING HARNESS CLAMP BRACKET
17118
25.REMOVE MANIFOLD STAY
22803
26.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY
23243B
27.REMOVE FUEL PUMP MOTOR WIRE
23273H
28.REMOVE NO. 2 FUEL HOSE
23271H
29.REMOVE NO. 1 FUEL HOSE
23804D
30.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)
23815D
31.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)
23804C
32.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23770
33.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
17111
34.REMOVE INTAKE MANIFOLD
35.REMOVE WIRING HARNESS CLAMP BRACKET
23811H
36.REMOVE NO. 1 FUEL PIPE (w/ DPF)
23760
37.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY
38.REMOVE WIRING HARNESS CLAMP BRACKET
Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.
23701
39.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23810A
40.REMOVE COMMON RAIL ASSEMBLY
19871
41.REMOVE NO. 1 GLOW PLUG CONNECTOR
19850
42.REMOVE GLOW PLUG ASSEMBLY
44781
43.REMOVE HOSE BRACKET
Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.
23300D
44.REMOVE DIESEL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)
Remove the 2 nuts and diesel fuel filter assembly from the cylinder block sub-assembly.
23780
45.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)
Remove the 2 nuts and No. 3 nozzle leakage pipe from the cylinder block sub-assembly.
16025
46.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.
88431
47.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.
89422C
48.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
16282
49.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)
Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.
Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.
16281
50.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.
23295D
51.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)
17168
52.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
89467B
53.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)
17167
54.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17271
55.REMOVE NO. 1 TURBO INSULATOR
56.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY
57.REMOVE EXHAUST PIPE SUPPORT STAY
25051
58.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
12261
59.REMOVE PCV HOSE
16279
60.REMOVE NO. 3 WATER BY-PASS PIPE
16268
61.REMOVE NO. 1 WATER BY-PASS PIPE
Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.
16284
62.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
17293
63.REMOVE TURBOCHARGER STAY
15474
64.REMOVE TURBO OIL OUTLET PIPE
15407
65.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
17201
66.REMOVE TURBOCHARGER SUB-ASSEMBLY
17141
67.REMOVE EXHAUST MANIFOLD
83530
68.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
16207
69.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.
Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.
16304
70.REMOVE WATER OUTLET SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.
Remove the gasket from the timing chain cover sub-assembly.
16321
71.REMOVE WATER INLET
Remove the 3 bolts and water inlet from the timing chain cover sub-assembly.
16331A
72.REMOVE THERMOSTAT
16603
73.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16620
74.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
25706
75.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Disconnect the No. 1 vacuum transmitting hose from the vacuum pump assembly.
Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.
29300
76.REMOVE VACUUM PUMP ASSEMBLY
Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.
Remove the 2 O-rings from the vacuum pump assembly.
11382C
77.REMOVE CAMSHAFT OIL SEAL RETAINER
Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.
13471
78.REMOVE CRANKSHAFT PULLEY
16575C
79.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.