Home › Engine / Hybrid System › 1GD-FTV LUBRICATION › OIL PUMP › 2015.11–2016.10
RM33K0E _51 Engine / Hybrid System _043583 1GD-FTV LUBRICATION _0225671 OIL PUMP A

1GD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the timing chain case assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of engine assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

(Click here)

·

w/ DPF:

(Click here)

·

for i-ART:

(Click here)


Clear Crank Time Compensation Data Engine starting
·

(Click here)

·

w/ DPF:

(Click here)

·

for i-ART:

(Click here)


Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

(Click here)

·

w/ DPF:

(Click here)

·

for i-ART:

(Click here)


·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization -
·

(Click here)

·

w/ DPF:

(Click here)

·

for i-ART:

(Click here)



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.



PROCEDURE

Hide 44763C 2.REMOVE NO. 2 HOSE TO HOSE TUBE

Hide 12632 3.REMOVE NO. 2 ENGINE COVER BRACKET

Hide 82121 4.REMOVE ENGINE WIRE

Hide 26100G 6.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 7.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 89481B 8.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 9.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 25733A 10.REMOVE NO. 1 VACUUM PIPE (w/ DPF)

Hide 12631A 13.REMOVE ENGINE COVER BRACKET

Hide 89421C 15.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 25625 16.REMOVE EGR VALVE BRACKET

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25601 19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25804 20.REMOVE VACUUM CONTROL VALVE SET

Hide 16209 21.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25800 22.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 23.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 27.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 28.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 29.REMOVE NO. 2 FUEL HOSE

Hide 23271H 30.REMOVE NO. 1 FUEL HOSE

Hide 23804D 31.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23815D 32.REMOVE NO. 3 FUEL PIPE (w/ DPF)

Hide 23804C 33.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 34.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 36.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 38.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 39.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23701 40.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 88431 42.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 16282 43.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

Hide 16281 44.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

Hide 23295D 45.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 17168 46.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 89467B 47.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)

Hide 16268 55.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 16284 56.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 15407 59.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 16207 61.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16304 62.REMOVE WATER OUTLET SUB-ASSEMBLY

Hide 16331A 64.REMOVE THERMOSTAT

Hide 16603 65.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A339577

Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.


Hide 16620 66.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A339579

Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


Hide 13471 67.REMOVE CRANKSHAFT PULLEY

Hide 16575C 68.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

Hide 12281A 69.REMOVE NO. 1 ENGINE HANGER

Hide 12501 70.REMOVE GENERATOR BRACKET SUB-ASSEMBLY

Hide 23670 71.REMOVE INJECTOR ASSEMBLY

Hide 23682 72.REMOVE NOZZLE HOLDER GASKET

Hide 11401G 73.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 74.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A339580C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.


b.
A339581C01
2.219,0.563 2.427,0.292 2.427,0.292 2.552,0.292 true 0.323,1.802 0.469,1.802 0.469,1.802 0.708,1.25 true 0.885,1.385 1.063,1.26 1.063,1.26 1.188,1.26 true 0.771,0.594 1.031,0.365 1.031,0.365 1.156,0.365 true 2.615,0.198 2.813,0.385 0.198,0.188 10 true *1 0.115,1.719 0.292,1.885 0.177,0.167 10 false *2 1.229,1.167 1.417,1.333 0.188,0.167 10 true *3 1.229,0.281 1.417,0.448 0.188,0.167 10 false *3
*1 Cylinder Head Cover Gasket
*2 No. 2 Cylinder Head Cover Gasket
*3 Camshaft Bearing Cap Oil Hole Gasket


Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.


Hide 12144 75.REMOVE OIL PAN COVER SILENCER

a.
A339601

Remove the 5 bolts and oil pan cover silencer from the oil pan sub-assembly.


Hide 89491 76.REMOVE ENGINE OIL LEVEL SENSOR

Hide 12101 77.REMOVE OIL PAN SUB-ASSEMBLY

a.
A339600C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 23 bolts and 2 nuts.


b.
A303108

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

·

Be careful not to damage the cylinder block sub-assembly flange.




Hide 16100 78.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 79.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11324 80.REMOVE TIMING CHAIN COVER PLATE

Hide 22100 81.REMOVE SUPPLY PUMP ASSEMBLY

Hide 22815A 82.REMOVE INJECTION PUMP INSULATOR

Hide 11302 83.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A339584

Remove the 20 bolts from the timing chain cover sub-assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

A339585C01
6.156,0.719 6.49,0.177 6.49,0.177 6.625,0.177 true 5.604,1.927 6.094,2.396 6.094,2.396 6.229,2.396 true 0.406,1.156 0.552,1.156 0.552,1.156 1.052,0.708 true 0.198,1.073 0.385,1.25 0.188,0.177 10 false *a 6.302,2.313 6.51,2.479 0.208,0.167 10 false *a 6.677,0.083 6.885,0.26 0.208,0.177 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.



c.
A339592

Remove the timing chain case gasket from the timing chain case assembly.


Hide 11303A 84.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A339586C01
0.583,1.271 1.271,1.271 true 1.417,0.917 2.167,0.354 2.167,0.354 2.375,0.354 true 2.448,0.271 2.656,0.458 0.208,0.188 10 false *a 0.354,1.188 0.563,1.375 0.208,0.188 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver and wooden block, pull out the front crankshaft oil seal.

NOTICE:

Do not damage the surface of the front crankshaft oil seal press fit hole.



Hide 85.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

a.
A339596

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.3 mm (0.000787 to 0.0118 in.)


Maximum gear backlash:

0.42 mm (0.0165 in.)


If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.


Hide 13519 86.REMOVE OIL PUMP DRIVE GEAR

a.
A339595

Remove the oil pump drive gear from the crankshaft.


Hide 13566B 87.REMOVE TIMING CHAIN GUIDE

Hide 13550 88.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 89.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

Hide 13562 90.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13507 91.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 13540 92.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 93.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

Hide 13561 94.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 95.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13523 96.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11310 97.REMOVE TIMING CHAIN CASE ASSEMBLY

a.
A339590

Remove the 15 bolts from the timing chain case assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.

A339591C01
0.729,0.646 0.865,0.646 0.865,0.646 1.167,1.24 true 5.823,2.094 6.323,2.479 6.323,2.479 6.469,2.479 true 6.323,0.552 6.656,1.219 6.656,1.219 6.802,1.219 true 0.479,0.552 0.698,0.74 0.219,0.188 10 false *a 6.521,2.385 6.74,2.573 0.219,0.188 10 false *a 6.854,1.125 7.052,1.292 0.198,0.167 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.



c.
A339593

Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.