Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM33K0E _51 Engine / Hybrid System _043566 1KD-FTV ENGINE CONTROL _0222113 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P2006  Intake Manifold Runner Control Stuck Closed (Bank 1)  


DESCRIPTION

The swirl control valve is mounted on the intake manifold. The vacuum switching valve is used to change the vacuum to control the swirl control valve.

The ECM determines the opening angle of the swirl control valve, and uses the vacuum switching valve (for swirl control valve) to change the vacuum applied to the actuator's diaphragm to open and close the swirl control valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) When actual intake air volume detected by mass air flow meter continues to be smaller than volume estimated from boost pressure and intake air temperature sensor, ECM determines that swirl control valve is stuck closed (1 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Open or short in vacuum switching valve (for swirl control valve) circuit

·

Intake manifold (swirl control valve)

·

Turbocharger sub-assembly

·

Mass air flow meter

·

Air cleaner hose

·

Vacuum hose

·

Air cleaner element is clogged

·

Intake hose is disconnected

·

ECM


Comes on DTC stored

A224013C01
4.323,2.51 4.24,1.573 4.24,1.573 4.156,1.573 true 4.417,2.833 4.771,4.208 4.771,4.208 4.896,4.208 false 5.688,3.073 5.844,3.344 5.844,3.344 5.979,3.344 false 4.708,2.844 4.938,3.802 4.938,3.802 5.063,3.802 false 2.5,0.323 2.823,0.594 0.323,0.271 10 false *1 4,1.5 4.24,1.708 0.24,0.208 10 false *2 6.021,3.25 6.344,3.51 0.323,0.26 10 false *3 5.125,3.708 5.448,3.938 0.323,0.229 10 false *4 4.927,4.146 5.24,4.375 0.313,0.229 10 false *5
*1 ECM *2 Swirl Control Valve
*3 Vacuum Pump *4 Vacuum Switching Valve (for swirl control valve)
*5 Swirl Control Valve Actuator - -


CONFIRMATION DRIVING PATTERN

P2006
DTC Detection Drive Pattern After warming up engine, drive vehicle at an engine speed of 3200 rpm or more with high load for 1 minute or more.*

HINT:

*: When the above driving pattern cannot be performed due to road conditions, etc., the swirl control valve can be determined to be functioning normally if MAF is 84 gm/sec or more and MAP is 110 kPa or higher when the engine speed is at 4000 rpm with no load. However, no DTCs are stored when inspecting the vehicle with this method.

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.


WIRING DIAGRAM

A377869E01
0.604,3.104 1.677,3.302 1.073,0.198 10 false Battery 0.49,2.438 1.563,2.635 1.073,0.198 10 false FL MAIN 3.0W 0.458,1.823 0.958,2.021 0.5,0.198 10 false J/B-B 1.896,1.646 2.969,2 1.073,0.354 10 false Instrument Panel Junction Block 1.875,1.344 2.979,1.542 1.104,0.198 10 false EFI-MAIN NO. 1 1.323,0.719 1.979,1.083 0.656,0.365 10 false EFI-MAIN NO. 1 0.979,0.583 1.292,0.75 0.313,0.167 10 false 2B 1.469,1.427 1.781,1.594 0.313,0.167 10 false 2J 3.552,0.583 3.865,0.75 0.313,0.167 10 false 2N 3.125,1.427 3.438,1.594 0.313,0.167 10 false 2P 5.781,0.583 6.094,0.75 0.313,0.167 10 false C73 5.781,2.646 6.094,2.813 0.313,0.167 10 false C74 5.698,1.99 6.125,2.156 0.427,0.167 10 false G130 1.021,0.385 1.333,0.552 0.313,0.167 10 false 1 3.594,0.385 3.906,0.552 0.313,0.167 10 false 1 5.198,0.49 5.51,0.656 0.313,0.167 10 false 1 4.427,0.469 4.74,0.635 0.313,0.167 10 false 2 3.26,1.25 3.573,1.417 0.313,0.167 10 false 9 1.583,1.25 1.896,1.417 0.313,0.167 10 false 5 4.125,1.073 5.677,1.469 1.552,0.396 10 false Vacuum Switching Valve (for Swirl Control Valve) 4.115,0.875 5.083,1.042 0.969,0.167 10 false C85*1, C86*2 6.125,0.583 6.625,0.781 0.5,0.198 10 false SCV 6.125,1.979 6.625,2.177 0.5,0.198 10 false MREL 6.125,2.635 6.625,2.833 0.5,0.198 10 false E1 5.844,2.438 6.021,2.604 0.177,0.167 10 false 7 5.813,1.813 5.99,1.979 0.177,0.167 10 false 8 5.813,0.396 6.063,0.573 0.25,0.177 10 false 15 6.344,3.26 6.844,3.458 0.5,0.198 10 false ECM 2.292,2.99 4.01,3.219 1.719,0.229 10 false *2: for Manual transmission 2.292,2.698 4.313,2.896 2.021,0.198 10 false *1: for Automatic transmission

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2006)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
P2006 A
P2006 and other DTCs B


HINT:

When MAP, mass air flow, Intake Air, and/or Intake Air Temp (Turbo)-related DTCs are stored along with P2006, perform troubleshooting for those DTCs first.

MAP-related DTCs: P0105, P0107 and P0108.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0105

MAF-related DTCs: P0100, P0102 and P0103.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0100

Intake Air-related DTCs: P0110, P0112 and P0113.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0110

Intake Air Temp (Turbo)-related DTCs: P0095, P0097 and P0098.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P007C




A

2.CHECK AIR INTAKE SYSTEM

B

2.CHECK AIR INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

Result:
Result Proceed to
Leaks and/or blockages exist in the intake system A
No leaks or blockages in the intake system B


HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check if the air cleaner element is significantly dirty.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

The swirl control valve does not move due to deposits or the diaphragm not being air-tight, etc., and the specified output performance cannot be obtained.

·

If operating normally, when the engine is started, the swirl control valve quickly moves from fully open to fully closed.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Check for any modifications in the intake system made by the user.





A

3.REPAIR OR REPLACE AIR INTAKE SYSTEM

B

4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
3.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.

Check the movement of the swirl control valve immediately after starting the engine.

A206071C05
4.49,3.021 5.198,3.563 true 5.198,3.563 5.458,3.552 true 5.531,3.469 5.844,3.667 0.313,0.198 10 false *1
*1 Swirl Control Valve - -


OK:

Swirl control valve rod moves smoothly in the direction indicated by the arrow in the illustration.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (MAF AND MAP)

NG

7.CHECK CONNECTION OF VACUUM HOSE
5.READ VALUE USING GTS (MAF AND MAP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
50003 234 3,4

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

Result:
Result Proceed to
MAF 84 gm/sec or more and MAP 117 kPa or higher C
MAP below 90 kPa B
Except above A


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.





A

6.CLEAN MASS AIR FLOW METER

B

10.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY

C

END

6.CLEAN MASS AIR FLOW METER
a.

Remove any deposits adhering to the mass air flow meter.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK CONNECTION OF VACUUM HOSE
a.

Check the connection of the swirl control valve system vacuum hose.


Result:
Proceed to
OK
NG



OK

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)

NG

11.REPAIR OR REPLACE VACUUM HOSE
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A208635N01
0.344,1.427 0.281,1.771 false 0.542,1.375 0.823,1.833 true 1.802,1.448 1.781,1.854 false 2,1.385 2.583,1.854 true 0.479,0.083 1.26,0.302 0.781,0.219 10 false VSV is ON 1.969,0.083 2.813,0.313 0.844,0.229 10 false VSV is OFF 0.635,0.458 0.927,0.698 0.292,0.24 10 false Air 2.094,0.458 2.396,0.667 0.302,0.208 10 false Air 2.656,0.563 3.292,0.833 0.635,0.271 10 false Air Filter 0.063,1.771 0.521,1.969 0.458,0.198 10 false Port F 0.896,1.781 1.396,2.01 0.5,0.229 10 false Port E 1.823,1.781 2.281,2 0.458,0.219 10 false Port F 2.656,1.792 3.167,2.01 0.51,0.219 10 false Port E

Disconnect the vacuum hoses from the VSV for swirl control valve.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 234 43

e.

Check the VSV operation when it is operated using the GTS.

OK:
GTS Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

9.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)

NG

13.REPLACE VACUUM CONTROL VALVE SET
9.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.

Inspect the intake manifold (swirl control valve).

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSPECTION

HINT:
·

If there are any deposits adhering to the valve, clean the valve.

·

If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.

·

Apply vacuum to the diaphragm of the swirl control valve and check that the valve opens and closes smoothly.




Result:
Proceed to
OK
NG



OK

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

12.REPLACE INTAKE MANIFOLD
10.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

b.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace the vacuum hose.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE INTAKE MANIFOLD
a.

Replace the intake manifold (swirl control valve).

Click hereEngine / Hybrid System>1GR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.REPLACE VACUUM CONTROL VALVE SET
a.

Replace the vacuum control valve set.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL

HINT:

Before replacing the vacuum control valve set, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

14.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
14.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A208635N02
0.344,1.417 0.281,1.76 false 0.542,1.375 0.823,1.833 true 1.802,1.448 1.781,1.854 false 1.99,1.385 2.573,1.854 true 0.458,0.063 1.208,0.292 0.75,0.229 10 false VSV is ON 1.969,0.052 2.823,0.26 0.854,0.208 10 false VSV is OFF 0.635,0.458 0.906,0.698 0.271,0.24 10 false Air 2.094,0.458 2.323,0.656 0.229,0.198 10 false Air 2.656,0.563 3.281,0.771 0.625,0.208 10 false Air Filter 0.083,1.781 0.49,1.938 0.406,0.156 10 false Port F 0.885,1.771 1.344,2.031 0.458,0.26 10 false Port E 1.844,1.771 2.292,2 0.448,0.229 10 false Port F 2.635,1.771 3.115,2.021 0.479,0.25 10 false Port E

Disconnect the vacuum hoses from the vacuum switching valve (for Swirl Control Valve).


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 234 43

e.

Check the VSV operation when it is operated using the GTS.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

15.REPLACE ECM
15.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
50003 234 3,4

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

OK:

MAF is 84 gm/sec or more and MAP is 110 kPa or more.


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.




Result:
Proceed to
NEXT



NEXT

END