The door control receiver receives signals from the door control transmitter and sends these signals to the body ECU. The body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.
If the body ECU has been replaced, it is necessary to initialize the body ECU.*1
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.*2
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION
*1: w/ Automatic Light Control System
*2: w/ Door Control Battery
Check the power door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Locked doors unlock
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the unlock warning switch assembly.
Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL
Inspect the unlock warning switch assembly.
Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G134 unlock warning switch assembly connector.
Disconnect the G33 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G134-1 - G33-8 (KSW) | Always | Below 1 Ω |
| G134-2 - Body ground | Always | Below 1 Ω |
| G134-1 or G33-8 (KSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Switch to self-diagnostic mode by operating the ignition key cylinder.
Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.
Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.
Within 30 seconds of turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and off.
If the system cannot enter self-diagnostic mode, the system returns to normal mode.
Turning the ignition switch to ON after the above operations have been completed ends self-diagnostic mode.
Do not lock or unlock doors during self-diagnostic mode.
Check that the system has switched to self-diagnostic mode by checking the interior light flash pattern.
| Proceed to |
| NEXT |
NEXT
Inspect the diagnostic outputs when the door control transmitter switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.
| Result | Proceed to |
|---|---|
| No diagnostic outputs | A |
| Unmatching recognition code is output | B |
| Normal wave (light flash pattern) is output | C |
A
B
C
Prepare the door control transmitter from another vehicle.
Press and hold down the door control transmitter switch.
Check that an unmatching recognition code is output.
| Result | Proceed to |
|---|---|
| Unmatching recognition code is not output | A |
| Unmatching recognition code is output | B |
A
B
Bring the door control transmitter near the door control receiver, and perform a wireless operation check.
When the door control transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
| Result | Proceed to |
|---|---|
| Wireless functions do not operate properly | A |
| Wireless functions operate properly | B |
A
B
| *a | Front view of wire harness connector
(to Door Control Receiver) |
Disconnect the door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G136-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G136-5 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Door Control Receiver) |
Connect the door control receiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G136-2 (RDA) - Body ground | Ignition switch off, all doors closed and door control transmitter switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter switch pressed | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G136 door control receiver connector.
Disconnect the G33 body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G136-2 (RDA) - G33-16 (RDA) | Always | Below 1 Ω |
| G136-3 (PRG) - G33-9 (PRG) | Always | Below 1 Ω |
| G136-2 (RDA) or G33-16 (RDA) - Body ground | Always | 10 kΩ or higher |
| G136-3 (PRG) or G33-9 (PRG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the door control receiver with a new or known good one.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the registration procedure.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the doors can be locked and unlocked by the door control transmitter lock and unlock switches.
Doors can be locked and unlocked by the door control transmitter.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmitter battery capacity.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Smart Entry and Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/o Smart Entry and Start System)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the diagnostic outputs when the door control transmitter switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.
| Result | Proceed to |
|---|---|
| Normal wave (light flash pattern) is output | A |
| Unmatching recognition code is output | B |
| No diagnostic outputs |
A
B
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.
Recognition code can be registered.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Smart Entry and Start System)>REMOVAL