Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224644 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Glass Breakage Sensor Circuit  


DESCRIPTION

When the glass breakage sensor detects that the back door glass, rear door quarter window glass LH or RH is tapped or broken, the sensor will set off the alarm for 30 seconds.

WIRING DIAGRAM

B433603E01
0.51,2.448 1.729,2.969 1.219,0.521 10 false Rear Door Quarter Window Glass RH 0.521,2.26 1.99,2.479 1.469,0.219 10 false N49 0.521,4.771 7.156,5.052 6.635,0.281 10 false N50 0.521,4.948 1.74,5.469 1.219,0.521 10 false Rear Door Quarter Window Glass LH 1.167,2.01 2.635,2.229 1.469,0.219 10 false SSR- 1.135,1.479 2.604,1.698 1.469,0.219 10 false SSR+ 1.594,1.354 3.063,1.573 1.469,0.219 10 false 2 1.594,1.896 3.063,2.115 1.469,0.219 10 false 1 5.125,1.365 6.594,1.583 1.469,0.219 10 false 2 5.354,1.469 6.823,1.688 1.469,0.219 10 false GPBS 5.396,2.521 6.865,2.74 1.469,0.219 10 false G34 5.406,2.677 6.875,2.896 1.469,0.219 10 false Body ECU 4.99,4.5 6.458,4.719 1.469,0.219 10 false b1 6.365,4.302 6.917,4.531 0.552,0.229 10 false 1 5.208,4.875 6.677,5.094 1.469,0.219 10 false Back Door Glass 1.594,3.823 3.063,4.042 1.469,0.219 10 false 2 1.604,4.385 3.073,4.604 1.469,0.219 10 false 1 1.146,4.49 2.615,4.708 1.469,0.219 10 false SSR- 1.135,3.938 2.604,4.156 1.469,0.219 10 false SSR+ 5.01,4.323 6.479,4.542 1.469,0.219 10 false 1 6.313,4.51 7.156,4.75 0.844,0.24 10 false b2

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Door control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BODY ECU - GLASS BREAKAGE SENSOR AND BODY GROUND)
a.

Disconnect the G34 body ECU connector.


b.

Disconnect the N49, N50 and B glass breakage sensor connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G34-2 (GPBS) - N49-2 (SSR+) Always Below 1 Ω
N49-1 (SSR-) - N50-2 (SSR+) Always Below 1 Ω
N50-1 (SSR-) - b1-1 (SSR+) Always Below 1 Ω
b2-1 (E) - Body ground Always Below 1 Ω
G34-2 (GPBS) - Body ground Always 10 kΩ or higher
N49-2 (SSR+) - Body ground Always 10 kΩ or higher
N49-1 (SSR-) - Body ground Always 10 kΩ or higher
N50-2 (SSR+) - Body ground Always 10 kΩ or higher
N50-1 (SSR-) - Body ground Always 10 kΩ or higher
b1-1 (SSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT REAR DOOR QUARTER WINDOW GLASS RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT REAR DOOR QUARTER WINDOW GLASS RH
a.

Disconnect the N49 rear door quarter window glass RH connector.


b.
B419473E01
1.01,0.583 1.198,0.583 1.198,0.583 1.646,1.24 true 1.823,1.573 2.24,1.073 2.24,1.073 2.438,1.073 true 0.635,0.479 1.25,0.677 0.615,0.198 10 false SSR- 2.469,0.979 3.083,1.177 0.615,0.198 10 false SSR+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SSR+) - 1 (SSR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR DOOR QUARTER WINDOW GLASS LH

NG

REPLACE REAR DOOR QUARTER WINDOW GLASS RH

3.INSPECT REAR DOOR QUARTER WINDOW GLASS LH
a.

Disconnect the N50 rear door quarter window glass LH connector.


b.
B419473E02
1.01,0.583 1.198,0.583 1.198,0.583 1.646,1.24 true 1.823,1.573 2.24,1.073 2.24,1.073 2.438,1.073 true 0.635,0.479 1.25,0.677 0.615,0.198 10 false SSR- 2.469,0.979 3.083,1.177 0.615,0.198 10 false SSR+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SSR+) - 1 (SSR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT BACK DOOR GLASS

NG

REPLACE REAR DOOR QUARTER WINDOW GLASS LH

4.INSPECT BACK DOOR GLASS
a.

Disconnect the b1 and b2 back door glass connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 - b2-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG