Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  Cranking Holding Function Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

13.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the engine switch on (IG) and the engine starts.

OK:
Switch Condition Starter Signal
Engine switch on (IG) OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

3.INSPECT ST NO. 1 RELAY

NG

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT ST NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

4.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay terminal holder) - C26-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay terminal holder) or C26-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D3-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay terminal holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-5 (L) - 2 (ST NO. 1 relay terminal holder) Always Below 1 Ω
G17-37 (STA) - 2 (ST NO. 1 relay terminal holder) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BATTERY - ST NO. 1 RELAY)
a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay terminal holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST NO. 1 RELAY - CERTIFICATION ECU)

NG

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST NO. 1 RELAY - CERTIFICATION ECU)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-5 (L) - G49-22 (STA) Always Below 1 Ω
C22-5 (L) or G49-22 (STA) or 2 (ST NO. 1 relay terminal holder) or G17-37 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G17-16 (STAR) - C22-4 (B) Always Below 1 Ω
G17-16 (STAR) - G49-11 (NSW) Always Below 1 Ω
G17-16 (STAR) or C22-4 (B) or G49-11 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the engine switch on (IG) and the engine starts.

OK:
Switch Condition Starter Signal
Engine switch on (IG) OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)