Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P2006  Intake Manifold Runner Control Stuck Closed (Bank 1)  


DESCRIPTION

The swirl control valve is mounted on the intake manifold. The vacuum switching valve is used to change the vacuum to control the swirl control valve.

The ECM determines the opening angle of the swirl control valve, and uses the vacuum switching valve (for swirl control valve) to change the vacuum applied to the actuator's diaphragm to open and close the swirl control valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) When actual intake air volume detected by mass air flow meter continues to be smaller than volume estimated from boost pressure and intake air temperature sensor, ECM determines that swirl control valve is stuck closed (1 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Open or short in vacuum switching valve (for swirl control valve) circuit

·

Intake manifold (swirl control valve)

·

Electric EGR control valve assembly

·

Turbocharger sub-assembly

·

Turbocharger nozzle vane control actuator

·

Mass air flow meter sub-assembly

·

Air cleaner hose

·

Vacuum hose

·

Air cleaner filter element is clogged

·

Intake hose is disconnected

·

ECM


Comes on DTC stored

A357985C01
3.74,2.531 3.417,1.823 3.417,1.823 3.313,1.823 true 5.438,2.708 5.646,2.042 5.646,2.042 5.76,2.042 true 3.99,2.844 4.302,3.635 4.302,3.635 4.417,3.635 true 4.573,2.844 4.885,3.635 4.885,3.635 5,3.635 true 2.063,0.344 2.375,0.5 0.313,0.156 10 false *1 3.146,1.74 3.458,1.896 0.313,0.156 10 false *2 5.792,1.979 6.104,2.135 0.313,0.156 10 false *3 5.031,3.552 5.344,3.708 0.313,0.156 10 false *4 4.438,3.552 4.75,3.708 0.313,0.156 10 false *5
*1 ECM *2 Swirl Control Valve
*3 Vacuum Pump *4 Vacuum Switching Valve (for Swirl Control Valve)
*5 Swirl Control Valve Actuator - -


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2006 After warming up engine, drive vehicle at an engine speed of 3200 rpm or more with high load for 1 minute or more.*

HINT:

*: When the above driving pattern cannot be performed due to road conditions, etc., the swirl control valve can be determined to be functioning normally if mass air flow is 84 gm/sec or more and MAP is 105 kPa or higher when the engine speed is at 4000 rpm with no load. However, no DTCs are stored when inspecting the vehicle with this method.

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.


WIRING DIAGRAM

A348547E16
3.063,1.042 3.521,1.24 0.458,0.198 10 false C110 3.073,1.229 6.208,1.458 3.135,0.229 10 false Vacuum Switching Valve (for Swirl Control Valve) 5.979,0.458 6.438,0.656 0.458,0.198 10 false 16 6.271,0.646 6.813,0.854 0.542,0.208 10 false SCV 5.938,0.656 6.396,0.854 0.458,0.198 10 false C38 6.271,4.229 6.813,4.438 0.542,0.208 10 false MREL 5.948,4.354 6.406,4.552 0.458,0.198 10 false G49 6,4.156 6.458,4.354 0.458,0.198 10 false 14 1.854,4.354 2.313,4.552 0.458,0.198 10 false 2K 5.115,2.813 5.573,3.01 0.458,0.198 10 false 2G 1.865,2.823 2.323,3.021 0.458,0.198 10 false 2B 1.865,3.219 2.323,3.417 0.458,0.198 10 false 2J 3.406,4.667 4.469,4.885 1.063,0.219 10 false EFI-MAIN NO. 1 2.479,5.01 4.615,5.24 2.135,0.229 10 false Instrument Panel Junction Block 0.594,5.667 1.365,5.865 0.771,0.198 10 false Battery 0.438,4.865 1.125,5.042 0.688,0.177 10 false FL MAIN 0.688,2.99 1.313,3.208 0.625,0.219 10 false J/B-B 0.698,2.688 0.885,2.885 0.188,0.198 10 false 1 0.969,2.688 1.188,2.896 0.219,0.208 10 false 2 2.281,4.156 3.344,4.375 1.063,0.219 10 false EFI-MAIN NO. 1 2.469,2.979 3.531,3.198 1.063,0.219 10 false EFI-MAIN NO. 2 3.396,3.531 4.458,3.75 1.063,0.219 10 false EFI-MAIN NO. 2 4.365,2.99 5.083,3.229 0.719,0.24 10 false EFI NO. 1 4.76,2.677 4.979,2.885 0.219,0.208 10 false 2 4.51,2.667 4.698,2.865 0.188,0.198 10 false 1 3.042,2.688 3.26,2.896 0.219,0.208 10 false 2 2.896,3.844 3.115,4.052 0.219,0.208 10 false 2 2.646,3.854 2.833,4.052 0.188,0.198 10 false 1 3.104,0.542 3.323,0.75 0.219,0.208 10 false 2 2.792,2.688 2.979,2.885 0.188,0.198 10 false 1 4.49,0.542 4.677,0.74 0.188,0.198 10 false 1 1.906,2.635 2.094,2.833 0.188,0.198 10 false 1 1.896,3.042 2.083,3.24 0.188,0.198 10 false 5 1.906,4.177 2.094,4.375 0.188,0.198 10 false 3 5.156,2.625 5.344,2.823 0.188,0.198 10 false 3 5.146,3.042 5.333,3.24 0.188,0.198 10 false 9 5.156,3.802 5.344,4 0.188,0.198 10 false 7 5.146,4.177 5.333,4.375 0.188,0.198 10 false 8 5.115,3.219 5.573,3.417 0.458,0.198 10 false 2P 5.104,3.99 5.563,4.188 0.458,0.198 10 false 2G 5.115,4.344 5.573,4.542 0.458,0.198 10 false 2P 6.438,5.656 6.979,5.865 0.542,0.208 10 false ECM 4.052,0.552 4.51,0.75 0.458,0.198 10 false SCV- 3.292,0.552 3.75,0.75 0.458,0.198 10 false SCV+

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2006)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Code.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
P2006 is output A
P2006 and other DTCs are output B


HINT:

When manifold absolute pressure sensor, mass air flow meter sub-assembly, intake air temperature sensor, and/or intake air temperature sensor (Turbo) related DTCs are stored along with P2006, perform troubleshooting for those DTCs first.

Manifold absolute pressure sensor-related DTCs: P0107 and P0108.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0107

Mass air flow meter sub-assembly-related DTCs: P0100.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0100

Intake air temperature sensor-related DTCs: P0112 and P0113.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0112

Intake air temperature sensor (Turbo)-related DTCs: P007C and P007D.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P007C




A

2.CHECK AIR INTAKE SYSTEM

B

2.CHECK AIR INTAKE SYSTEM
a.

Check for air leakage and blockage between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.

Result:
Result Proceed to
Leaks and/or blockages exist in the intake system A
No leaks or blockages in the intake system B


HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check if the air cleaner element is significantly dirty.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Check for any modifications in the intake system made by the user.





A

3.REPAIR OR REPLACE INTAKE SYSTEM

B

4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
3.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the intake system.


Result:
Proceed to
NEXT



NEXT

4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 234 43

e.
A356877

Perform the Active Test.

OK:

Swirl control valve rod moves smoothly in the direction indicated by the arrow in the illustration.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (MAF AND MAP)

NG

7.CHECK CONNECTION OF VACUUM HOSE
5.READ VALUE USING GTS (MAF AND MAP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
50003 234 3,4

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

Result:
Result Proceed to
MAF 84 gm/sec or more and MAP 105 kPa or higher C
MAP below 90 kPa B
Except above A


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.





A

6.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

10.INSPECT TURBOCHARGER NOZZLE VANE PLATE

C

END

6.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK CONNECTION OF VACUUM HOSE
a.

Check the connection of the swirl control valve system vacuum hose.


Result:
Proceed to
OK
NG



OK

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)

NG

11.REPAIR OR REPLACE VACUUM HOSE
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588E23
0.458,1.438 0.313,1.677 false 0.667,1.396 0.917,1.885 true 2,1.417 1.844,1.646 false 2.177,1.375 2.5,1.844 true 0.823,0.031 1.531,0.24 0.708,0.208 10 false VSV is ON 2.458,0.021 3.24,0.229 0.781,0.208 10 false VSV is OFF 0.573,0.365 0.792,0.563 0.219,0.198 10 false Air 2.333,1.833 2.813,2.031 0.479,0.198 10 false Port E 0.771,1.906 1.25,2.104 0.479,0.198 10 false Port E 1.625,1.625 2.094,1.823 0.469,0.198 10 false Port F 0.104,1.688 0.573,1.885 0.469,0.198 10 false Port F 2.031,0.417 2.25,0.615 0.219,0.198 10 false Air 2.76,0.74 3.333,0.938 0.573,0.198 10 false Air Filter

Disconnect the vacuum hoses from the VSV for swirl control valve.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 234 43

e.

Check the VSV operation when it is operated using the GTS.

OK:
GTS Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

9.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

12.REPLACE VACUUM CONTROL VALVE SET
9.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Inspect the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSPECTION

HINT:
·

If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.

·

When inspecting the electric EGR control valve assembly, make sure that the valve is fully closed.




Result:
Proceed to
OK
NG



OK

15.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)

NG

14.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
10.INSPECT TURBOCHARGER NOZZLE VANE PLATE

b.

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.



c.
A348999

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane support plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

REPLACE TURBOCHARGER NOZZLE VANE CONTROL ACTUATOR

NG

11.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace the vacuum hose.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE VACUUM CONTROL VALVE SET
a.

Replace the vacuum control valve set.

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL

HINT:

Before replacing the vacuum control valve set, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

13.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
13.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588E23
0.458,1.438 0.313,1.677 false 0.667,1.396 0.917,1.885 true 2,1.417 1.844,1.646 false 2.177,1.375 2.5,1.844 true 0.823,0.031 1.531,0.24 0.708,0.208 10 false VSV is ON 2.458,0.021 3.24,0.229 0.781,0.208 10 false VSV is OFF 0.573,0.365 0.792,0.563 0.219,0.198 10 false Air 2.333,1.833 2.813,2.031 0.479,0.198 10 false Port E 0.771,1.906 1.25,2.104 0.479,0.198 10 false Port E 1.625,1.625 2.094,1.823 0.469,0.198 10 false Port F 0.104,1.688 0.573,1.885 0.469,0.198 10 false Port F 2.031,0.417 2.25,0.615 0.219,0.198 10 false Air 2.76,0.74 3.333,0.938 0.573,0.198 10 false Air Filter

Disconnect the vacuum hoses from the vacuum switching valve (for swirl control valve).


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 234 43

e.

Check the VSV operation when it is operated using the GTS.

OK:
GTS Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

16.REPLACE ECM
14.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
15.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.

Inspect the intake manifold (swirl control valve).

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSPECTION

HINT:
·

If there are any deposits adhering to the valve, clean the valve.

·

If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.

·

Apply vacuum to the diaphragm of the swirl control valve and check that the valve opens and closes smoothly.




Result:
Proceed to
OK
NG



OK

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

18.REPLACE INTAKE MANIFOLD
16.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.


e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

OK:

MAF is 84 gm/sec or more and MAP is 105 kPa or higher.


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.




Result:
Proceed to
NEXT



NEXT

END

18.REPLACE INTAKE MANIFOLD
a.

Replace the intake manifold (swirl control valve).

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED