Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P2009  Intake Manifold Runner Control Circuit Low (Bank 1)  P2010  Intake Manifold Runner Control Circuit High (Bank 1)  


DESCRIPTION

Refer to DTC P2006.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P2006

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2009 Intake Manifold Runner Control Circuit Low (Bank 1) Open in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Open in vacuum switching valve (for swirl control valve) circuit

·

ECM


Comes on DTC stored
P2010 Intake Manifold Runner Control Circuit High (Bank 1) Short in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic).
·

Vacuum switching valve (for swirl control valve)

·

Short in vacuum switching valve (for swirl control valve) circuit

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2009
P2010
2 seconds after engine is started, race engine for 1 second

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588C02
0.458,1.448 0.365,1.688 false 0.656,1.396 0.906,1.885 true 1.969,1.417 1.844,1.781 false 2.146,1.375 2.469,1.844 true 0.823,0.073 1.531,0.281 0.708,0.208 10 false VSV is ON 2.458,0.063 3.24,0.271 0.781,0.208 10 false VSV is OFF 0.781,0.427 1,0.625 0.219,0.198 10 false Air 2.521,1.76 3,1.958 0.479,0.198 10 false Port E 0.958,1.802 1.438,2 0.479,0.198 10 false Port E 1.906,1.708 2.375,1.906 0.469,0.198 10 false Port F 0.219,1.729 0.688,1.927 0.469,0.198 10 false Port F 2.229,0.438 2.448,0.635 0.219,0.198 10 false Air 2.76,0.583 3.333,0.781 0.573,0.198 10 false Air Filter

Connect the GTS to the DLC3.


b.

Disconnect the vacuum hoses from the vacuum switching valve (for swirl control valve).


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 234 43

e.

Check the VSV operation when it is operated using the GTS.

OK:
GTS Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)
2.INSPECT VACUUM SWITCHING VALVE FOR SWIRL CONTROL VALVE (RESISTANCE)
a.

Inspect the vacuum switching valve (for swirl control valve).

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)

NG

6.REPLACE VACUUM CONTROL VALVE SET
3.INSPECT VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) (POWER SOURCE VOLTAGE)
a.

Disconnect the vacuum switching valve (for swirl control valve) connector.


b.
A249191C08
0.458,1.052 0.906,1.313 0.448,0.26 1.958,1.271 2.51,1.708 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.521,1.104 0.958,1.302 0.438,0.198 10 false C110 2.552,1.74 3.125,1.948 0.573,0.208 10 false SCV+
*a Front view of wire harness connector
(to Vacuum Switching Valve (for Swirl Control Valve))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C110-2 (SCV+) - Body ground Engine switch on (IG) 11 to 14 V



c.

Reconnect the vacuum switching valve (for swirl control valve) connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - INSTRUMENT PANEL JUNCTION BLOCK)
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - ECM)
a.

Disconnect the vacuum switching valve (for swirl control valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C110-1 (SCV-) - C38-10 (SCV) Always Below 1 Ω
C110-1 (SCV-) or C38-10 (SCV) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the vacuum switching valve (for swirl control valve) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE VACUUM CONTROL VALVE SET
a.

Replace the vacuum control valve set.

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR SWIRL CONTROL VALVE) - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Remove the instrument panel junction block connector.


b.

Disconnect the vacuum switching valve (for swirl control valve) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-3 - C110-2 (SCV+) Always Below 1 Ω
2G-3 or C110-2 (SCV+) - Body ground and other terminals Always 10 kΩ or higher



d.

Reinstall the instrument panel junction block connector.


e.

Reconnect the vacuum switching valve (for swirl control valve) connector.


Result:
Proceed to
OK
NG



OK

8.INSPECT ECM POWER SOURCE CIRCUIT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.INSPECT ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END