Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2016.07
RM33K0E _51 Engine / Hybrid System _054512 2TR-FBE ENGINE CONTROL _0269966 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P16A1  Delivery Heater Control Module Stuck ON  P16A3  Cylinder 1 Delivery Heater Circuit/Open  P16A4  Cylinder 2 Delivery Heater Circuit/Open  P16A5  Cylinder 3 Delivery Heater Circuit/Open  P16A6  Cylinder 4 Delivery Heater Circuit/Open  P16A7  Cylinder 1 Delivery Heater Circuit High  P16A8  Cylinder 2 Delivery Heater Circuit High  P16A9  Cylinder 3 Delivery Heater Circuit High  P16AA  Cylinder 4 Delivery Heater Circuit High  P16AB  Disconnection between Delivery Heater and Delivery Heater Control Module  


DESCRIPTION

Refer to DTC P16A0.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P16A0

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P16A1 Delivery Heater Control Module Stuck ON The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (1 trip detection logic). Glow plug controller Does not come on DTC stored
P16A3 Cylinder 1 Delivery Heater Circuit/Open An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Open in No. 1 glow plug circuit

·

GLOW relay


Does not come on DTC stored
P16A4 Cylinder 2 Delivery Heater Circuit/Open An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Open in No. 2 glow plug circuit

·

GLOW relay


Does not come on DTC stored
P16A5 Cylinder 3 Delivery Heater Circuit/Open An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Open in No. 3 glow plug circuit

·

GLOW relay


Does not come on DTC stored
P16A6 Cylinder 4 Delivery Heater Circuit/Open An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Open in No. 4 glow plug circuit

·

GLOW relay


Does not come on DTC stored
P16A7 Cylinder 1 Delivery Heater Circuit High A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug assembly

·

Short in No. 1 glow plug circuit


Does not come on DTC stored
P16A8 Cylinder 2 Delivery Heater Circuit High A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug assembly

·

Short in No. 2 glow plug circuit


Does not come on DTC stored
P16A9 Cylinder 3 Delivery Heater Circuit High A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug assembly

·

Short in No. 3 glow plug circuit


Does not come on DTC stored
P16AA Cylinder 4 Delivery Heater Circuit High A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug assembly

·

Short in No. 4 glow plug circuit


Does not come on DTC stored
P16AB Disconnection between Delivery Heater and Delivery Heater Control Module A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

Short in glow plug circuit


Does not come on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Clear the DTCs.

3.

Turn the ignition switch off for 30 seconds or more.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Using the GTS, switch the ECM from normal mode to check mode.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P16A1, P16A3 P16A4, P16A5, P16A6, P16A7, P16A8, P16A9, P16AA or P16AB.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P16A3, P16A4, P16A5 and/or P16A6 is output A
P16A7, P16A8, P16A9 and/or P16AA is output B
P16A1 and/or P16AB is output C




A

2.PERFORM ACTIVE TEST USING GTS (DELIVERY HEATER)

B

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - GLOW PLUG CONNECTOR)

C

11.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - GLOW PLUG CONNECTOR)
2.PERFORM ACTIVE TEST USING GTS (DELIVERY HEATER)
a.
A241159C19
0.646,1.115 1.063,1.417 0.417,0.302 1.927,1.719 1.76,1.24 true 0.167,0.219 0.479,0.417 0.313,0.198 10 false *a 0.74,1.188 1.052,1.385 0.313,0.198 10 false A44 1.979,1.656 2.594,1.854 0.615,0.198 10 false BATT
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Delivery Heater.

Powertrain > Engine and ECT > Active Test
Tester Display
Delivery Heater
50004 234 326

f.

Operate the delivery heater using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
A44-1(BATT) - Body ground Delivery heater is ON 11 to 14 V


HINT:

Maximum operation time is 10 seconds.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - GLOW PLUG CONNECTOR)

NG

5.INSPECT GLOW RELAY
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - GLOW PLUG CONNECTOR)
a.

Disconnect connectors of the glow plug controller.

A382060C05
0.125,0.417 0.542,0.698 0.417,0.281 0.115,0.854 0.531,1.156 0.417,0.302 0.115,1.281 0.531,1.604 0.417,0.323 0.104,1.74 0.521,2.073 0.417,0.333 2.385,1.26 2.802,1.542 0.417,0.281 4.583,1.26 5,1.542 0.417,0.281 1.219,0.917 1.563,0.552 1.563,0.552 1.74,0.552 true 3.448,1.479 3.031,2.104 true 3.75,1.469 4.073,2.135 true 5.667,1.469 5.417,2.135 true 6.031,1.448 6.313,2.135 true 0.271,0.469 0.729,0.667 0.458,0.198 10 false g1 0.271,0.917 0.729,1.115 0.458,0.198 10 false g2 0.271,1.354 0.729,1.552 0.458,0.198 10 false g3 0.25,1.823 0.708,2.021 0.458,0.198 10 false g4 1.792,0.479 1.948,0.677 0.156,0.198 10 false 1 2.458,1.302 2.917,1.5 0.458,0.198 10 false C45 4.667,1.323 5.125,1.521 0.458,0.198 10 false C44 0.76,0.104 1.073,0.302 0.313,0.198 10 false *1 2.688,0.594 3,0.792 0.313,0.198 10 false *a 4.708,0.615 5.021,0.813 0.313,0.198 10 false *b 2.865,2.177 3.323,2.375 0.458,0.198 10 false GL1 3.958,2.177 4.417,2.375 0.458,0.198 10 false GL2 5.313,2.188 5.771,2.385 0.458,0.198 10 false GL3 6.198,2.198 6.656,2.396 0.458,0.198 10 false GL4
*1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the glow plug connector from the glow plug assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-1 (GL1) - g1-1 Always Below 1 Ω
C45-2 (GL2) - g2-1 Always Below 1 Ω
C44-1 (GL3) - g3-1 Always Below 1 Ω
C44-2 (GL4) - g4-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT GLOW PLUG ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT GLOW PLUG ASSEMBLY

Result:
Proceed to
OK
NG



OK

NG

REPLACE FUEL DELIVERY PIPE SUB-ASSEMBLY (GLOW PLUG ASSEMBLY)

5.INSPECT GLOW RELAY

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR

NG

REPLACE GLOW RELAY

6.CHECK HARNESS AND CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the GLOW relay from the engine room relay block and junction block assembly.


d.

Disconnect connectors of the glow plug controller.


e.

Disconnect the ECM connectors.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GLOW relay terminal 5 - Battery positive terminal Always Below 1 Ω
GLOW relay terminal 1 - Body ground Always Below 1 Ω
GLOW relay terminal 3 - A44-1 (BATT) Always Below 1 Ω
GLOW relay terminal 2 - G57-7 (GREL) Always Below 1 Ω
GLOW relay terminal 5 or Battery positive terminal - Body ground Always 10 kΩ or higher
GLOW relay terminal 3 or A44-1 (BATT) - Body ground Always 10 kΩ or higher
GLOW relay terminal 2 or G57-7(GREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - GLOW PLUG CONNECTOR)
a.

Disconnect connectors of the glow plug controller.

A382060C05
0.125,0.417 0.542,0.698 0.417,0.281 0.115,0.854 0.531,1.156 0.417,0.302 0.115,1.281 0.531,1.604 0.417,0.323 0.104,1.74 0.521,2.073 0.417,0.333 2.385,1.26 2.802,1.542 0.417,0.281 4.583,1.26 5,1.542 0.417,0.281 1.219,0.917 1.563,0.552 1.563,0.552 1.74,0.552 true 3.448,1.479 3.031,2.104 true 3.75,1.469 4.073,2.135 true 5.667,1.469 5.417,2.135 true 6.031,1.448 6.313,2.135 true 0.271,0.469 0.729,0.667 0.458,0.198 10 false g1 0.271,0.917 0.729,1.115 0.458,0.198 10 false g2 0.271,1.354 0.729,1.552 0.458,0.198 10 false g3 0.25,1.823 0.708,2.021 0.458,0.198 10 false g4 1.792,0.479 1.948,0.677 0.156,0.198 10 false 1 2.458,1.302 2.917,1.5 0.458,0.198 10 false C45 4.667,1.323 5.125,1.521 0.458,0.198 10 false C44 0.76,0.104 1.073,0.302 0.313,0.198 10 false *1 2.688,0.594 3,0.792 0.313,0.198 10 false *a 4.708,0.615 5.021,0.813 0.313,0.198 10 false *b 2.865,2.177 3.323,2.375 0.458,0.198 10 false GL1 3.958,2.177 4.417,2.375 0.458,0.198 10 false GL2 5.313,2.188 5.771,2.385 0.458,0.198 10 false GL3 6.198,2.198 6.656,2.396 0.458,0.198 10 false GL4
*1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the glow plug connector from the glow plug assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-1 (GL1) or g1-1 - Other terminals Always 10 kΩ or higher
C45-2 (GL2) or g2-1 - Other terminals Always 10 kΩ or higher
C44-1 (GL3) or g3-1 - Other terminals Always 10 kΩ or higher
C44-2 (GL4) or g4-1 - Other terminals Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

8.REPLACE GLOW PLUG CONTROLLER

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2TR-FBE FUEL>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

No DTC is output.


HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE FUEL DELIVERY PIPE SUB-ASSEMBLY (GLOW PLUG ASSEMBLY)

11.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - GLOW PLUG CONNECTOR)
a.

Disconnect connectors of the glow plug controller.

A382060C05
0.125,0.417 0.542,0.698 0.417,0.281 0.115,0.854 0.531,1.156 0.417,0.302 0.115,1.281 0.531,1.604 0.417,0.323 0.104,1.74 0.521,2.073 0.417,0.333 2.385,1.26 2.802,1.542 0.417,0.281 4.583,1.26 5,1.542 0.417,0.281 1.219,0.917 1.563,0.552 1.563,0.552 1.74,0.552 true 3.448,1.479 3.031,2.104 true 3.75,1.469 4.073,2.135 true 5.667,1.469 5.417,2.135 true 6.031,1.448 6.313,2.135 true 0.271,0.469 0.729,0.667 0.458,0.198 10 false g1 0.271,0.917 0.729,1.115 0.458,0.198 10 false g2 0.271,1.354 0.729,1.552 0.458,0.198 10 false g3 0.25,1.823 0.708,2.021 0.458,0.198 10 false g4 1.792,0.479 1.948,0.677 0.156,0.198 10 false 1 2.458,1.302 2.917,1.5 0.458,0.198 10 false C45 4.667,1.323 5.125,1.521 0.458,0.198 10 false C44 0.76,0.104 1.073,0.302 0.313,0.198 10 false *1 2.688,0.594 3,0.792 0.313,0.198 10 false *a 4.708,0.615 5.021,0.813 0.313,0.198 10 false *b 2.865,2.177 3.323,2.375 0.458,0.198 10 false GL1 3.958,2.177 4.417,2.375 0.458,0.198 10 false GL2 5.313,2.188 5.771,2.385 0.458,0.198 10 false GL3 6.198,2.198 6.656,2.396 0.458,0.198 10 false GL4
*1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the glow plug connector from the glow plug assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-1 (GL1) or g1-1 -Other terminals Always 10 kΩ or higher
C45-2 (GL2) or g2-1 - Other terminals Always 10 kΩ or higher
C44-1 (GL3) or g3-1 - Other terminals Always 10 kΩ or higher
C44-2 (GL4) or g4-1 - Other terminals Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR