Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.07
RM33K0E _51 Engine / Hybrid System _054513 2TR-FBE ENGINE MECHANICAL _0272877 ENGINE ASSEMBLY A

2TR-FBE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P0630 is output (Click here)
Code registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly Inspection after repair Poor idle, engine start, etc. (Click here)
·

Replacement of throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of piston or piston ring

·

Replacement of mass air flow meter sub-assembly

·

Replacement of fuel injector assembly

·

Replacement of fuel pump

·

Replacement of air fuel ratio sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Replacement of knock sensor


Inspection after repair Poor idle, engine start, etc. (Click here)
for AC60E:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60E:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

CAUTION:
·
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.

·
A343701

Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·
A343693

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 6.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 7.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 53301 8.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose from the hood sub-assembly.


b.

Remove the 4 bolts and hood sub-assembly from the 2 hood hinge assemblies.


Hide 17705 9.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

a.
A346135

Disconnect the intake mass air flow meter connector and detach the 2 wire harness clamps.


b.
A346136

Detach the 4 clamps.


c.

Loosen the hose clamp and remove the air cleaner cap sub-assembly with No. 1 air cleaner hose.


Hide 17801 10.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 17701 11.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A344949

Detach the 3 wire harness clamps.


b.
A349779

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 17861 12.REMOVE INTAKE AIR CONNECTOR

Hide 51410 13.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 14.REMOVE NO. 2 ENGINE UNDER COVER

Hide 53737B 15.REMOVE FRONT UPPER FENDER APRON SEAL LH

a.

Remove the 6 clips and front upper fender apron seal LH.


Hide 53736 16.REMOVE FRONT UPPER FENDER APRON SEAL RH

a.

Remove the 5 clips and front upper fender apron seal RH.


Hide 53882F 17.REMOVE FRONT FENDER SEAL LH

a.

Remove the 6 clips and front fender seal LH.


Hide 53882F 18.REMOVE FRONT FENDER SEAL RH

a.

Remove the 6 clips and front fender seal RH.


Hide 53294C 19.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 53293C 20.REMOVE RADIATOR SIDE DEFLECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 16593 21.REMOVE NO. 1 RADIATOR AIR GUIDE

Hide 16571 22.REMOVE RADIATOR HOSE INLET

Hide 16572 23.REMOVE RADIATOR HOSE OUTLET

Hide 17621A 24.DISCONNECT AIR PUMP INLET

Hide 16470 25.REMOVE RADIATOR RESERVOIR

Hide 16711 26.REMOVE FAN SHROUD

Hide 32941 27.DISCONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 32942 28.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 16400 29.REMOVE RADIATOR ASSEMBLY

Hide 30.DISCONNECT HEATER HOSE

a.
A382727

Slide the clamp and disconnect the heater water outlet hose from the heater radiator unit sub-assembly.


b.

Slide the clamp and disconnect the heater water inlet hose from the heater radiator unit sub-assembly.


Hide 44320 31.DISCONNECT VANE PUMP ASSEMBLY

a.

Disconnect the power steering oil pressure switch connector.


b.
A348584

Remove the 2 bolts and disconnect the vane pump assembly.

NOTICE:

Do not hit other parts with the pulley when disconnecting the vane pump assembly.


HINT:

Be sure to suspend the vane pump assembly securely.



Hide 15301 32.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 33.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the bolt, engine oil level dipstick guide and O-ring.

NOTICE:

Cover the engine oil level dipstick guide hole to prevent foreign matter from entering it.



Hide 88320 34.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 28100 35.REMOVE STARTER ASSEMBLY

Hide 36.DISCONNECT PURGE LINE HOSE

A382728

a.

Slide the clamp and disconnect the purge line hose from the purge VSV.


Hide 44774 37.DISCONNECT UNION TO CONNECTOR TUBE HOSE

a.
A382729

Slide the clamp and disconnect the union to connector tube hose from the intake manifold.


Hide 17344 38.DISCONNECT NO. 4 AIR INJECTION SYSTEM HOSE

Hide 23273C 39.DISCONNECT NO. 2 FUEL HOSE

Hide 23271H 40.DISCONNECT NO. 1 FUEL HOSE

Hide 55550 41.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 43.DISCONNECT ENGINE WIRE

a.
A356084

Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.


b.
A382730

Disconnect the 3 glow plug controller connectors.


c.
A382731

Disconnect the air injection control driver connector.


d.

Detach the clamp.


e.

Remove the bolt and disconnect the engine wire from the air injection control bracket.


f.
A382732

Detach the grommet and pull out the engine wire from the cabin.


g.
A382733

Disconnect the connector from the engine room main wire.


h.
A348572

Remove the nut and disconnect the engine room main wire from the positive (+) battery terminal.


i.
A348573

Loosen the nut and remove the positive (+) battery terminal.


j.
A348575

Loosen the 2 nuts and remove the battery hold down clamp.


k.

Remove the battery.


l.

Remove the battery tray.


m.
A348576

Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.


n.
A348577

Detach the clamp and remove the bolt and No. 2 engine wire.


o.
A348579

Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.


p.
A348580

Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.


q.
A348581

Remove the nut and disconnect the engine wire from the engine room relay block.


r.

Disconnect the 2 connectors from the engine room relay block.


s.

Detach the clamp.


t.
A348582

Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.


u.
A348583

Disconnect the air fuel ratio sensor connector.


v.

Remove the bolt and disconnect the sensor bracket from the right side of the frame.


Hide 17410 44.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 46.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 33030 47.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 35000 48.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 31210 49.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 50.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 51.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 32101 52.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 11355 53.REMOVE REAR END PLATE

a.
A348585

Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.


b.

Remove the bolt and rear end plate from the cylinder block sub-assembly.


Hide 54.INSTALL ENGINE HANGER

a.
A348586C01
0.042,0.021 0.229,0.229 0.188,0.208 10 false *a 1.854,0.021 2.063,0.219 0.208,0.198 10 false *b
*a Rear Side
*b Front Side


Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-0C010
12281-0C030
Bolt 90119-T0388
91672-81025



Hide 55.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine assembly with a chain block.


b.
A348587

Remove the 4 bolts and 4 nuts from the body.


c.

Remove the engine assembly by operating the engine sling device and chain block.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




Hide 56.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.




b.

Remove the 2 bolts and 2 engine hangers.


Hide 82121 57.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.


Hide 12391 58.REMOVE FRONT ENGINE MOUNTING HEAT INSULATOR RH

a.
A348589

Remove the bolt and front engine mounting heat insulator RH from the front engine mounting insulator.


Hide 12361 59.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A348590C01
0.052,0.031 0.271,0.25 0.219,0.219 10 false *a 0.052,2.469 0.271,2.688 0.219,0.219 10 true *b
*a LH Side
*b RH Side


Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.