When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
44763C
1.REMOVE NO. 2 HOSE TO HOSE TUBE
Slide the clamp and disconnect the union to check valve hose from the vacuum pump assembly.
Remove the 2 bolts and No. 2 hose to hose tube from the cylinder head cover sub-assembly and hose bracket.
12632
2.REMOVE NO. 2 ENGINE COVER BRACKET
82121
3.REMOVE ENGINE WIRE
17363K
4.REMOVE INTERCOOLER AIR TUBE
26100G
5.REMOVE DIESEL THROTTLE BODY ASSEMBLY
16278
6.REMOVE NO. 2 WATER BY-PASS PIPE
89481B
7.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
89425
8.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
89425
9.REMOVE EXHAUST GAS TEMPERATURE SENSOR (for i-ART)
25733A
10.REMOVE NO. 1 VACUUM PIPE (w/ DPF)
25734
11.REMOVE NO. 2 VACUUM PIPE (w/ DPF)
17578B
12.REMOVE PIPE CLAMP (w/ DPF)
17578B
13.REMOVE PIPE CLAMP (for i-ART)
12631A
14.REMOVE ENGINE COVER BRACKET
Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.
23265C
15.REMOVE GAS FILTER
89421C
16.REMOVE DIESEL TURBO PRESSURE SENSOR
25625
17.REMOVE EGR VALVE BRACKET
25612
18.REMOVE NO. 2 EGR PIPE
16206B
19.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
25601
20.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
except i-ART:
Disconnect the connector from the common rail assembly.
Detach the 2 clamps and remove the connecting wire from the hose bracket.
Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.
Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
25804
21.REMOVE VACUUM CONTROL VALVE SET
16209
22.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
| *1 | No. 6 Water By-pass Hose |
| *2 | No. 7 Water By-pass Hose |
| *3 | Water Hose |
Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.
Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.
25800
23.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY
11409
24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23812D
25.REMOVE NO. 2 FUEL PIPE
Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.
Remove the bolt and No. 2 fuel pipe from the manifold stay.
26.REMOVE WIRING HARNESS CLAMP BRACKET
17118
27.REMOVE MANIFOLD STAY
22803
28.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY
23243B
29.REMOVE FUEL PUMP MOTOR WIRE
23273H
30.REMOVE NO. 2 FUEL HOSE
23271H
31.REMOVE NO. 1 FUEL HOSE
23804D
32.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)
23815D
33.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)
23804C
34.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23770
35.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
17111
36.REMOVE INTAKE MANIFOLD
37.REMOVE WIRING HARNESS CLAMP BRACKET
23811H
38.REMOVE NO. 1 FUEL PIPE (w/ DPF)
23760
39.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY
40.REMOVE WIRING HARNESS CLAMP BRACKET
Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.
23701
41.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
23810A
42.REMOVE COMMON RAIL ASSEMBLY
19871
43.REMOVE NO. 1 GLOW PLUG CONNECTOR
19850
44.REMOVE GLOW PLUG ASSEMBLY
44781
45.REMOVE HOSE BRACKET
Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.
23300D
46.REMOVE DIESEL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)
Remove the 2 nuts and diesel fuel filter assembly from the cylinder block sub-assembly.
23780
47.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)
Remove the 2 nuts and No. 3 nozzle leakage pipe from the cylinder block sub-assembly.
16025
48.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.
88431
49.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.
89422C
50.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
16282
51.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)
Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.
Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.
16281
52.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.
23295D
53.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)
17168
54.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
89467B
55.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)
17167
56.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17271
57.REMOVE NO. 1 TURBO INSULATOR
58.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY
59.REMOVE EXHAUST PIPE SUPPORT STAY
25051
60.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
12261
61.REMOVE PCV HOSE
16279
62.REMOVE NO. 3 WATER BY-PASS PIPE
16268
63.REMOVE NO. 1 WATER BY-PASS PIPE
Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.
16284
64.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
17293
65.REMOVE TURBOCHARGER STAY
15474
66.REMOVE TURBO OIL OUTLET PIPE
15407
67.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
17201
68.REMOVE TURBOCHARGER SUB-ASSEMBLY
17141
69.REMOVE EXHAUST MANIFOLD
83530
70.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
16207
71.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.
Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.
16304
72.REMOVE WATER OUTLET SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.
Remove the gasket from the timing chain cover sub-assembly.
16321
73.REMOVE WATER INLET
Remove the 3 bolts and water inlet from the timing chain cover sub-assembly.
16331A
74.REMOVE THERMOSTAT
16603
75.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16620
76.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
25706
77.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
Disconnect the No. 1 vacuum transmitting hose from the vacuum pump assembly.
Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.
29300
78.REMOVE VACUUM PUMP ASSEMBLY
Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.
Remove the 2 O-rings from the vacuum pump assembly.
11382C
79.REMOVE CAMSHAFT OIL SEAL RETAINER
Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.
13471
80.REMOVE CRANKSHAFT PULLEY
16575C
81.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.