Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2016.10
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


DESCRIPTION

The ECM performs a Diesel Oxidation Catalyst (DOC) removal and loss of function check every 800 km (approximate). The catalyst is warmed by injecting fuel (post injection) through the main injector during the exhaust stroke while driving.

If the temperature difference detected by the exhaust temperature sensors before and after the catalyst is equal to or below the threshold during high load driving, the system determines that the Diesel Oxidation Catalyst (DOC) has been removed and there is a loss of function, and illuminates the MIL.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0420 Catalyst System Efficiency Below Threshold (Bank 1) The temperature difference before and after the catalyst is equal to or below the threshold even with post injection during high load driving.
(1 trip detection logic).
·

Exhaust manifold converter sub-assembly

·

Exhaust gas temperature sensor

·

No. 2 exhaust gas temperature sensor

·

Mass air flow meter sub-assembly


Common Inspection Item:
·

Fuel injection system


·

Fuel with low cetance number used


Comes on DTC stored

Related Data List
DTC No. Data List
P0420
·

Exhaust Temperature B1S1

·

Exhaust Temperature B1S2

·

Actual EGR Valve Pos.

·

MAF



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0420 After engine warm-up, enter DOC Removal Check Mode using the GTS and accelerate up to 80 km/h or more and then drive at a constant speed for 1 minute.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Record the stored DTC and freeze frame data.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0420 is output A
Other relevant DTCs are output B




A

3.CHECK INSTALLATION CONDITION (EXHAUST GAS TEMPERATURE SENSOR AND EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY)

B

3.CHECK INSTALLATION CONDITION (EXHAUST GAS TEMPERATURE SENSOR AND EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY)
a.

Check the installation condition of the exhaust gas temperature sensor, No. 2 exhaust gas temperature sensor and exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EMISSION CONTROL SYSTEM>PARTS LOCATION

Result:
Result Proceed to
Parts are correctly installed. A
Parts are not installed.
(Parts have been modified, etc.)
B




A

4.CHECK EXHAUST GAS TEMPERATURE SENSOR

B

15.REPAIR OR REPLACE MALFUNCTIONING PARTS
4.CHECK EXHAUST GAS TEMPERATURE SENSOR
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


f.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.


g.

Check the exhaust temperature while idling and after racing the engine at 4000 rpm for 1 minute.

Powertrain > Engine and ECT > Data List
Tester Display
Exhaust Temperature B1S1
Exhaust Temperature B1S2
50003 234 858,859
Standard Temperature:
Engine Condition Exhaust Temperature B1S1 Exhaust Temperature B1S2
Idling 150°C (302°F) or higher 150°C (302°F) or higher
After racing engine for 1 minute at 4000 rpm (without load) Increases by 50°C (90°F) or more than idling exhaust temperature


Result:
Proceed to
OK
NG




OK

5.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 5)

NG

11.REPLACE EXHAUST GAS TEMPERATURE SENSOR OR NO. 2 EXHAUST GAS TEMPERATURE SENSOR
5.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 5)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Common Rail (All).


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
6.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
a.

Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken in procedure 5 when the engine was idling and at 4000 rpm with no load.

Result:
Snapshot Data Action Proceed to
Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st Go to Fuel Injection System (from step 3) A
Injection Volume is less than 10 mm3/st at 4000 rpm Go to Fuel Injection System (from step 19) B
Except above Check mass air flow meter volume C


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





C

7.READ VALUE USING GTS (MAF AND ENGINE SPEED)

B

17.GO TO DETERMINE CAUSE OF MALFUNCTION FOR INJECTION VOLUME

A

18.DETERMINE CAUSE OF MALFUNCTION FOR INJECTION FEEDBACK VAL #1 TO #4
7.READ VALUE USING GTS (MAF AND ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / MAF and Engine speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
MAF
50003 234 9,3

d.

Start the engine and read the value when 30 seconds has elapsed.

Standard:
Engine speed MAF
Idling
·

3 to 15 gm/sec (EGR on)

·

10 to 21 gm/sec (EGR off)


3000 rpm
·

35 to 89 gm/sec (EGR on)

·

72 to 94 gm/sec (EGR off)





Result:
Proceed to
OK
NG



OK

8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

NG

16.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
8.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(for i-ART)>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL PROPERTY
9.CHECK FUEL PROPERTY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / Actual EGR Valve Pos.


f.

While idling, check the Actual EGR Valve Pos. Data List item.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

If the EGR value remains at 0% after restarting the engine and driving the vehicle, the cetane number of the fuel is low. Therefore, EGR is prohibited.



Result:
Result Proceed to
Actual EGR Valve Pos. is more than 0% A
Actual EGR Valve Pos. is 0% B




A

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

B

12.REPLACE FUEL
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off and wait for 30 seconds.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Utility / DOC Removal Check Mode.


f.

Perform the DOC Removal Check Mode.

Powertrain > Engine and ECT > Utility
Tester Display
DOC Removal Check Mode
50005 234 4465

g.

Remove the GTS from the DLC3.

HINT:

DOC Removal Check Mode is maintained until the ignition switch is turned off. Therefore, even if the GTS is removed, it is possible to drive the vehicle.



h.

Start the engine.


i.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


j.

After engine warm-up, accelerate up to 80 km/h or more and then drive at a constant speed for 1 minute.


k.

Connect the GTS to the DLC3.


l.

Confirm that the DTC does not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0420.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and it can be determined that the system is normal.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

·

If the judgment result shows ABNORMAL, perform the procedure again from the beginning, as the cause may be from another source.





Result:
Proceed to
NEXT



NEXT

END

11.REPLACE EXHAUST GAS TEMPERATURE SENSOR OR NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

b.

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL PROPERTY
12.REPLACE FUEL
a.

Replace the fuel.

HINT:

Do not use fuel with a low cetance number.



b.

After replacing the fuel, drive the vehicle for approximately 15 km to consume any of the remaining previous fuel.


Result:
Proceed to
NEXT



NEXT

13.PERFORM LEARNING (FUEL PROPERTY JUDGMENT)
13.PERFORM LEARNING (FUEL PROPERTY JUDGMENT)
a.

Start the engine.


b.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


c.

Race the engine from idling to 4000 rpm 15 times.

HINT:

If the cetane number is determined to be low during the learning procedure, EGR is prohibited while idling.



Result:
Proceed to
NEXT



NEXT

14.CHECK FUEL PROPERTY
14.CHECK FUEL PROPERTY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / Actual EGR Valve Pos.


f.

While idling, check the Actual EGR Valve Pos. Data List item.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

If the EGR value remains at 0% after restarting the engine and driving the vehicle, the cetane number of the fuel is low. Therefore, EGR is prohibited.



Standard:

Actual EGR Valve Pos. is more than 0%


Result:
Proceed to
NEXT




NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

If an exhaust gas temperature sensor, No. 2 exhaust gas temperature sensor or exhaust manifold converter sub-assembly is not installed, install or replace the specified part.

Result:
Proceed to
NEXT




NEXT

9.CHECK FUEL PROPERTY
16.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:
·

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.

·

Before replacing the mass air flow meter sub-assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL PROPERTY
17.GO TO DETERMINE CAUSE OF MALFUNCTION FOR INJECTION VOLUME
a.

Perform troubleshooting from Fuel Injection System step 19 (REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS) and onward.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>Fuel Injection System


b.

Proceed to the next step after repairs have been completed.


Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL PROPERTY
18.DETERMINE CAUSE OF MALFUNCTION FOR INJECTION FEEDBACK VAL #1 TO #4
a.

Perform troubleshooting from Fuel Injection System step 3 (PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)) and onward.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>Fuel Injection System


b.

Proceed to the next step after repairs have been completed.


Result:
Proceed to
NEXT



NEXT

9.CHECK FUEL PROPERTY