Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2016.10
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P2032  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)  P2033  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2)  


DESCRIPTION

Refer to DTC P0545.

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P0545

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) No. 2 exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Coolant temperature is 70°C (158°F) or higher

·

The exhaust gas temperature sensor is continuously 120°C (248°F) or more for 15 seconds.


·

Open or short in No. 2 exhaust gas temperature sensor circuit

·

No. 2 exhaust gas temperature sensor

·

ECM


Comes on DTC stored
P2033 Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2) No. 2 exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·

After starting the engine, 11 minutes or more elapses

·

Coolant temperature is 70°C (158°F) or higher

·

The exhaust gas temperatur e sensor is continuously 120°C (248°F) or more for 15 seconds.


·

Open or short in No. 2 exhaust gas temperature sensor circuit

·

No. 2 exhaust gas temperature sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2032
P2033
Exhaust Temperature B1S2

HINT:
·

Sensor 2 represents the sensor located downstream of the DOC catalyst.

·

When DTC P2032 and P2033 is output, check the downstream exhaust gas temperature indicated by "Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2" using the GTS.


Reference:
Condition Exhaust Temperature B1S2 No. 2 Exhaust Gas Temperature Sensor Condition
Idling with warm engine Constant at between 50 and 700°C (122 and 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the No. 2 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2032
P2033
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), allowing 11 minutes to elapse after starting the engine and waiting for the exhaust gas temperature sensor to be 120°C (248°F) or more for 15 seconds.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (NO. 2 EXHAUST TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2.


d.

Read the value.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 234 859
Standard:

Same as the actual No. 2 exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) B
OK: Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warmup), and varies after maintaining an engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a short circuit, the GTS will indicate 0°C (32°F).

·

If there is an open circuit, the GTS will indicate 1000°C (1832°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A356525C13
1.479,2.719 1.927,3.052 0.448,0.333 1.281,4.229 1.615,3.573 true 2.313,4.219 1.823,3.573 true 0.563,2.76 0.875,2.958 0.313,0.198 10 false *a 0.688,1.802 1,2 0.313,0.198 10 false *1 2.583,1.771 2.896,1.969 0.313,0.198 10 false *2 1.573,0.667 1.99,0.854 0.417,0.188 10 false THCO 1.635,1.375 2.083,1.573 0.448,0.198 10 false E2 1.542,2.813 1.99,3.031 0.448,0.219 10 false C139 1.167,4.26 1.458,4.438 0.292,0.177 10 false E2 2.229,4.26 2.625,4.458 0.396,0.198 10 false THCO
*1 No. 2 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor)


Disconnect the No. 2 exhaust gas temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THCO) of the No. 2 exhaust gas temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2.


f.

Read the value.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 234 859
Standard:

1000°C (1832°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the No. 2 exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C139-2 (THCO) - C38-33 (THCO) Always Below 1 Ω
C139-1 (E2) - C38-26 (ETCO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A178587C05
0.792,1.594 1.104,1.792 0.313,0.198 10 false *1 2.698,1.677 3.01,1.875 0.313,0.198 10 false *2
*1 No. 2 Exhaust Gas Temperature Sensor
*2 ECM


Disconnect the No. 2 exhaust gas temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S2.


e.

Read the value.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 234 859
Standard:

0°C (32°F)



Result:
Proceed to
OK
NG



OK

7.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
7.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the No. 2 exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C114-2 (THCO) or C57-33 (THCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine and turn the GTS on.


f.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher), allowing 11 minutes to elapse after starting the engine and waiting for the exhaust gas temperature sensor to be 120°C (248°F) or more for 15 seconds.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END