Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _037990 1KD-FTV ENGINE CONTROL _0184269 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List MAF
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter.



Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List MAP

Turbocharger System
Main fault
·

Air leak in the turbocharged air passage

·

ECM not operating well

·

Turbocharger (turbine, bearing)


Symptoms Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List MAP
·

With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.

·

Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.



Exhaust System
Main fault Blockage
Symptoms Lack of power (high engine speed, under heavy load)

Glow System
Main fault Open circuit, glow plug relay fault
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug

Battery
Main fault Battery is depleted
Symptoms Difficult to start (cannot crank, crank speed is low), horn is quiet
Data List Battery Voltage
When cranking, battery voltage is below 5 V.

Engine - 1
Main fault Damaged, seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.



Start System
Main fault Starter system malfunction
Symptoms Difficult to start
Data List Starter Signal
·

Ignition switch (STA) output:

ON: Starter is operating

OFF: Starter is not operating




b.

Diesel Injection

Fuel Supply Pump
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure, Target Pump SCV Current
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

Fuel Filter
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Common Rail Pressure is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Pressure Discharge Valve
Main fault Does not completely close
Symptoms Difficult to start, engine stall, rough idle, lack of power

Injector Driver
Main fault Circuit fault: The injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Common Rail Pressure, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Common Rail Pressure and Common Rail Pres Sens 2 follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Common Rail Pressure or Common Rail Pres Sens 2 decreases to a value less than Target Common Rail Pressure).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position

100%: Fully open

0%: Fully closed

·

When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Starting Trouble


·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Battery Voltage

·

Starter Signal

·

Engine Speed of Cyl #1 (to #4)

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Common Rail Pressure

·

Common Rail Pressure

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position



CAUTION / NOTICE / HINT

Explanation of Symptom



Starting Trouble For good starting it is essential to have:
·

Sufficient cranking speed.

·

Properly operating engine preheating system.

·

Good quality fuel.


The fuel is ignited by the heat which is generated by compression pressure.
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air.
Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open.

Trouble Area Chart According to Problem Cause



A210593E14
0.813,8.51 1,8.677 0.188,0.167 10 false A 3.594,0.948 5.208,1.135 1.615,0.188 10 false Depleted battery 0.25,0.146 1.281,0.333 1.031,0.188 10 false Difficult to start 0.865,0.979 2.25,1.156 1.385,0.177 10 false Does not crank at all 0.771,4.135 2.396,4.333 1.625,0.198 10 false Cranking speed too slow 0.792,5.635 2.813,5.823 2.021,0.188 10 false Difficult to start (cranking is OK) 3.594,1.74 6.021,1.948 2.427,0.208 10 false ECM power supply circuit malfunction 3.594,2.531 6.229,2.729 2.635,0.198 10 false Clutch pedal switch assembly malfunction 3.594,3.208 6.031,3.542 2.438,0.333 10 false Immobiliser system or entry and start system fault 3.594,4.125 4.854,4.313 1.26,0.188 10 false Depleted battery 4.115,6.542 6.781,6.719 2.667,0.177 10 false Fuel is not supplied to fuel supply pump 1.719,6.552 3.052,6.729 1.333,0.177 10 false Fuel pressure is low 4.115,7.302 6.021,7.51 1.906,0.208 10 false Fuel supply pump malfunction 4.115,8.073 6.385,8.271 2.271,0.198 10 false Common rail assembly malfunction 3.594,4.906 6.313,5.333 2.719,0.427 10 false Increased internal friction of the engine mechanical parts (oil too thick, seizure, etc.)

A183464E14
0.844,0.135 1,0.302 0.156,0.167 10 false A 4.188,0.771 6.292,0.958 2.104,0.188 10 false Injector driver circuit malfunction 1.76,0.771 3.115,0.948 1.354,0.177 10 false Fuel pressure is high 4.177,1.542 5.667,1.75 1.49,0.208 10 false Air in injector assembly 4.198,2.385 6.115,2.573 1.917,0.188 10 false Injector assembly malfunction 1.771,2.375 3.156,2.583 1.385,0.208 10 false Specific cylinder fault 4.177,3.135 5.917,3.344 1.74,0.208 10 false Low compression pressure 4.177,4.021 5.802,4.208 1.625,0.188 10 false Glow system malfunction 1.76,3.99 3.406,4.198 1.646,0.208 10 false Difficult to start when cold 4.177,4.76 6.406,5.115 2.229,0.354 10 false Engine coolant temperature sensor malfunction 1.76,6.135 2.854,6.344 1.094,0.208 10 false Poor fuel quality

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing the Fuel Supply Pump, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK. A
Low cranking speed.
HINT:

When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.


B
Does not crank at all. C




A

2.READ ALL OUTPUT DTCS

B

C

33.READ OUTPUT DTC (RELATED TO ENGINE)
2.READ ALL OUTPUT DTCS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Utility / All Codes.

Result:
Result Proceed to
No DTC is output A
DTCs related to engine are output B




A

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

B

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data.


d.

Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.

·

Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.




Result:
Proceed to
NEXT



NEXT

4.CHECK SNAPSHOT (COMMON RAIL PRESSURE)
4.CHECK SNAPSHOT (COMMON RAIL PRESSURE)
a.

Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was started.

A227761E07
2.375,0.865 2.458,0.865 2.458,0.865 2.479,1.177 false 2.813,0.573 2.74,0.573 false 4.115,0.625 3.99,0.625 3.99,0.625 3.813,0.792 false 4.01,2.344 3.917,2.344 3.917,2.344 3.802,2.229 false 3.938,2.875 3.865,2.875 3.865,2.875 3.792,2.792 false 5.552,0.438 5.396,0.438 5.396,0.438 5.115,0.917 false 5.552,1.563 5.458,1.563 5.458,1.563 5.313,1.25 false 5.542,1.906 5.417,1.906 5.417,1.906 5.25,1.5 false 5.552,2.24 5.438,2.24 5.438,2.24 5.146,2.646 false 1.958,2.333 2.063,2.333 2.063,2.333 2.26,2.99 false 0.083,1.74 1.042,1.948 0.958,0.208 10 false Fuel Pressure 3.969,2.792 4.104,2.969 0.135,0.177 10 false a 2.844,0.49 2.99,0.667 0.146,0.177 10 false b 4.146,0.542 4.313,0.708 0.167,0.167 10 false d 4.052,2.271 4.198,2.448 0.146,0.177 10 false c 1.104,0.781 2.5,1.063 1.396,0.281 10 false Target Fuel Pressure 5.594,2.177 7.135,2.406 1.542,0.229 10 false Abnormal Fuel Pressure 5.594,1.479 7.063,1.74 1.469,0.26 10 false Normal Fuel Pressure 5.563,0.354 7.156,0.635 1.594,0.281 10 false Abnormal Fuel Pressure 5.604,1.823 7.156,2.052 1.552,0.229 10 false Abnormal Fuel Pressure 1.115,2.156 2.031,2.573 0.917,0.417 10 false Engine cranking start 2.5,3.208 3.604,3.385 1.104,0.177 10 false About 2 seconds

Result:
Result Proceed to
At the point in the illustration labeled "a", Common Rail Pressure is less than 10000 kPa from the value of Common Rail Pressure when cranking started A
At the point in the illustration labeled "c", Common Rail Pressure is below Target Common Rail Pressure by 15000 kPa or more B
Common Rail Pressure increases to a value that is higher than Target Common Rail Pressure immediately after cranking, and, at the point in the illustration labeled "d", Common Rail Pressure is higher than Target Common Rail Pressure C
Except above D


HINT:
·

Even if Common Rail Pressure is temporarily higher than Target Common Rail Pressure, as shown at the point in the illustration labeled "b", the fuel supply pump is normal.

·

Fuel pressure is about 25000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.

·

Fuel pressure increases rapidly during cranking.





A

5.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP

B

14.READ VALUE USING GTS (COMMON RAIL PRESSURE)

C

18.INSPECT INJECTOR DRIVER

D

20.CHECK DATA LIST
5.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
a.

Disconnect the inlet hose from the fuel supply pump.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

OK:

Fuel is properly supplied to the fuel supply pump when the priming pump is operated.


HINT:
·

When there is a lack of fuel, fuel pressure drops.

·

Inspect for Fuel Filter clogging (check that the Fuel Filter is not clogged).




c.

Reconnect the inlet hose.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

12.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
6.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C119-1 - C55-2 (PCV+) Always Below 1 Ω
C119-2 - C55-1 (PCV-) Always Below 1 Ω
C119-1 or C55-2 (PCV+) - Body ground Always 10 kΩ or higher
C119-2 or C55-1 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

9.PERFORM FUEL SUPPLY PUMP INITIALIZATION
9.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

10.READ VALUE USING GTS (COMMON RAIL PRESSURE)
10.READ VALUE USING GTS (COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Common Rail Pressure.

Powertrain > Engine > Data List
Tester Display
Common Rail Pressure
50003 234 851

d.

Start the engine.


e.

Read the Common Rail Pressure values while cranking and idling the engine.

Result:
Result Proceed to
The engine cannot be started or the engine can be started but Common Rail Pressure is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A




A

END

B

11.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
11.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug assembly for all the cylinders.

Click hereEngine / Hybrid System>1KD-FTV STARTING>GLOW PLUG>REMOVAL


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.




c.

Install the glow plug assembly.

Click hereEngine / Hybrid System>1KD-FTV STARTING>GLOW PLUG>INSTALLATION


Result:
Proceed to
NEXT



NEXT

24.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
12.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
a.

Check and repair or replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

13.BLEED AIR FROM FUEL SYSTEM
13.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

28.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.READ VALUE USING GTS (COMMON RAIL PRESSURE)
a.

Check Common Rail Pressure in the snapshot taken in procedure 3 when the engine was warmed up.

Result:
Result Proceed to
Common Rail Pressure is more than 5000 kPa from Target Common Rail Pressure A
Except above B




A

15.REPLACE FUEL SUPPLY PUMP

B

16.PERFORM FUEL SUPPLY PUMP INITIALIZATION
15.REPLACE FUEL SUPPLY PUMP
a.

Replace the fuel supply pump.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.PERFORM FUEL SUPPLY PUMP INITIALIZATION
16.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
18.INSPECT INJECTOR DRIVER
a.

Even in cases where DTC P0200 is not stored even though the engine cannot be started, perform the DTC P0200 troubleshooting procedure.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>P0200

HINT:
·

When the engine cannot be started due to a malfunction in the injector driver system, once the DTCs are cleared, the system cannot store DTC P0200 even if it is confirmed that the engine cannot be started when trying to reproduce the problem symptoms.

As DTC P0200 cannot be stored when starting the engine, fuel injection signals are output by the ECM, but fuel is not actually injected. Therefore, an excessive amount of fuel is supplied to the common rail by the fuel supply pump assembly, and as a result, the fuel pressure is higher than the target common rail pressure in the data recorded at the time the engine was having trouble starting.

·

If the problem cannot be determined even after performing the DTC P0200 troubleshooting procedure and the fuel pressure is higher than the target common rail pressure when attempting to start the engine, proceed to the next step.




Result:
Proceed to
NEXT



NEXT

19.INSPECT INJECTOR ASSEMBLY
19.INSPECT INJECTOR ASSEMBLY
a.
A191333C13
1.885,1.083 2,1.229 0.115,0.146 10 false 2 1.479,1.083 1.594,1.229 0.115,0.146 10 false 1 0.177,0.281 0.323,0.427 0.146,0.146 10 false *a
*a Component without harness connected
(fuel injector assembly)


Disconnect the fuel injector connectors.


b.

Measure the resistance of the fuel injector.

OK:

No open circuit malfunction.



c.

Reconnect the fuel injector connectors.


Result:
Proceed to
OK
NG



OK

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

REPLACE INJECTOR ASSEMBLY

20.CHECK DATA LIST
a.

Check Injection Feedback Val # in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Injection Feedback Val #1 to #4 are 3 mm3/st or less.
Injection Volume is more than 12 mm3/st.
A
*
Injection Feedback Val for at least one cylinder is more than +3 mm3/st
HINT:

There may be a malfunction in the corresponding cylinder.


B
Except above C


HINT:
·

*: When this case occurs, usually symptoms may be noticeable, such as difficulty starting, lack of power.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.





A

21.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

22.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

29.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
21.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
22.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
50004 234 111 379,380,381,382

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other. B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

23.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

24.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
23.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

24.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

24.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
HINT:

It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.


a.

Replace the injector assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
25.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

26.BLEED AIR FROM FUEL SYSTEM
26.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

27.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
27.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

28.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
28.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

29.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
a.

Check the temperature when starting trouble occurs.

Result:
Result Proceed to
Difficult to start only for cold engine. A
Difficult to start both for cold and warmed up engine. B




A

30.READ VALUE USING GTS (COOLANT TEMP)

B

32.CHECK FUEL QUALITY
30.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 234 8

d.

Read the value displayed on the GTS.

OK:

Coolant Temp is not high when the engine is cold, and not low after the engine is warmed up



Result:
Proceed to
OK
NG



OK

31.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

31.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

32.CHECK FUEL QUALITY

NG

REPLACE GLOW PLUG ASSEMBLY

32.CHECK FUEL QUALITY
a.

Check that only diesel fuel is being used.


b.

Check that the fuel does not contain any impurities.


Result:
Proceed to
NEXT



NEXT

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
33.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
DTCs related to engine are output B




A

34.CHECK COMMUNICATION BETWEEN GTS AND ECM

B

34.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a GTS that is able to communicate with other vehicles.


OK:

Communication is possible (vehicle can be recognized).



Result:
Proceed to
OK
NG



OK

35.READ VALUE USING GTS (STARTER SIGNAL AND NEUTRAL POSITION SW SIGNAL)

NG

35.READ VALUE USING GTS (STARTER SIGNAL AND NEUTRAL POSITION SW SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal and Neutral Position SW Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
Neutral Position SW Signal
50003 234 118,147

d.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Starter Signal Cranking ON
Neutral Position SW Signal Shift lever in neutral ON



Result:
Result Proceed to
OK A
NG (for Manual transmission) B
NG (for Automatic transmission) C



A

36.CHECK STARTING SYSTEM

B

INSPECT CLUTCH SWITCH ASSEMBLY

C

36.CHECK STARTING SYSTEM
a.

Inspect the starting system.

HINT:

Be sure to inspect the following areas:

·

Starter relay

·

Starter

·

Immobiliser system




Result:
Proceed to
NEXT



NEXT

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END