Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2015.06–2016.03
RM3250E _59 Vehicle Exterior _038076 WIPER / WASHER _0184382 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

The headlight leveling ECU assembly controls the headlight cleaner motor and pump assembly.

WIRING DIAGRAM

E328595E01
0.458,0.385 2.292,0.583 1.833,0.198 10 false from Battery 0.396,1.542 3.604,1.74 3.208,0.198 10 false from IG1 NO.1 Relay*1 0.51,2 3.719,2.198 3.208,0.198 10 false from Ignition Switch*2 1.844,0.563 3.073,0.76 1.229,0.198 10 false H-LP CLN 3.448,1.719 4.677,1.917 1.229,0.198 10 false IG1 NO.4 3.865,0.292 4.021,0.49 0.156,0.198 10 false 1 3.323,0.292 3.479,0.49 0.156,0.198 10 false 2 3.094,0.542 3.552,0.74 0.458,0.198 10 false A58 3.094,0.698 4.594,1.063 1.5,0.365 10 false Headlight Cleaner Motor and Pump Assembly 5.76,0.531 6.073,0.729 0.313,0.198 10 false PB 5.771,1.646 6.083,1.844 0.313,0.198 10 false IG 5.771,2.896 6.083,3.094 0.313,0.198 10 false H 5.781,6.802 6.094,7 0.313,0.198 10 false E 1.385,2.771 1.844,2.969 0.458,0.198 10 false HLC 1.26,3.823 1.719,4.021 0.458,0.198 10 false FRWA 0.24,4.385 5.74,4.583 5.5,0.198 10 false Headlight Leveling ECU Assembly 0.25,4.229 0.708,4.427 0.458,0.198 10 false A80 2.573,5.49 6.552,5.688 3.979,0.198 10 false Combination Meter Assembly 2.552,7.135 4.167,7.479 1.615,0.344 10 false Brake Actuator Assembly (Skid Control ECU) 0.688,8.417 4.667,8.615 3.979,0.198 10 false : CAN Communication Line 0.146,7.292 4.583,7.49 4.438,0.198 10 false *1: w/ Entry and Start System 0.125,7.719 4.563,7.917 4.438,0.198 10 false *2: w/o Entry and Start System 1.833,2.646 2.292,2.844 0.458,0.198 10 false 16 1.854,3.688 2.01,3.885 0.156,0.198 10 false 4 5.542,0.281 5.698,0.479 0.156,0.198 10 false 6 5.531,1.417 5.688,1.615 0.156,0.198 10 false 3 5.542,2.635 5.698,2.833 0.156,0.198 10 false 2 5.531,6.552 5.688,6.75 0.156,0.198 10 false 4 5.76,7.115 6.219,7.313 0.458,0.198 10 false A57 5.75,7.281 6.854,7.625 1.104,0.344 10 false Headlight Cleaner Control Relay

E328596E01
0.063,4.094 4.5,4.292 4.438,0.198 10 false *1: w/ Entry and Start System 0.073,4.469 4.51,4.667 4.438,0.198 10 false *2: w/o Entry and Start System 0.427,0.438 3.635,0.635 3.208,0.198 10 false from IG1 NO.1 Relay*1 0.49,0.823 3.698,1.021 3.208,0.198 10 false from Ignition Switch*2 2.698,0.594 3.615,0.792 0.917,0.198 10 false WASHER 0.167,3.167 0.625,3.365 0.458,0.198 10 false G18 0.177,3.333 5.073,3.531 4.896,0.198 10 false Windshield Wiper Switch Assembly 1.823,1.865 2.135,2.063 0.313,0.198 10 false WF 1.427,1.854 1.74,2.052 0.313,0.198 10 false EW 3.615,0.563 3.927,0.76 0.313,0.198 10 false A2 4.021,0.313 4.177,0.51 0.156,0.198 10 false 1 4.552,0.302 4.708,0.5 0.156,0.198 10 false 2 3.615,0.719 5.219,1.083 1.604,0.365 10 false Windshield Washer Motor and Pump Assembly 0.281,1.51 3.948,1.708 3.667,0.198 10 false Windshield Washer Switch 0.656,2.042 1.115,2.24 0.458,0.198 10 false OFF 0.677,2.24 1.135,2.438 0.458,0.198 10 false ON 1.208,1.844 1.365,2.042 0.156,0.198 10 false T 0.26,1.875 0.417,2.073 0.156,0.198 10 false P 2.25,2.542 2.563,2.74 0.313,0.198 10 false WF 2.229,2.865 2.542,3.063 0.313,0.198 10 false EW 2.573,2.302 2.729,2.5 0.156,0.198 10 false 7 2.573,2.635 2.729,2.833 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

First check that the front washer operates normally.

·

Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.

·

The headlight cleaner system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the window defogger system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

w/ Automatic Headlight Beam Level Control System:

If the headlight leveling ECU assembly has been replaced, it is necessary to initialize the headlight leveling ECU assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 361

b.

Check for DTCs.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 361
OK:

DTC is not output.



Result:
Result Proceed to
OK A
NG (w/ Automatic Headlight Beam Level Control System) B
NG (w/o Automatic Headlight Beam Level Control System) C



A

2.READ VALUE USING GTS

B

C

2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Window Washer Switch Washer switch condition ON/OFF ON: Windshield wiper switch assembly (windshield washer switch) on
OFF: Windshield wiper switch assembly (windshield washer switch) off
-
Body Electrical > HL AutoLeveling > Data List
Tester Display
Front Window Washer Switch
50003 361 1
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

3.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - WINDSHIELD WIPER SWITCH ASSEMBLY)
3.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
a.

Remove the headlight cleaner motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL


b.

Inspect the headlight cleaner motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT HEADLIGHT CLEANER CONTROL RELAY

NG

REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

4.INSPECT HEADLIGHT CLEANER CONTROL RELAY
a.

Remove the headlight cleaner control relay.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>REMOVAL


b.

Inspect the headlight cleaner control relay.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)

NG

REPLACE HEADLIGHT CLEANER CONTROL RELAY

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)
a.
E139345C09
1.51,0.385 1.875,0.615 0.365,0.229 1.01,1.844 1.167,1.844 1.167,1.844 1.438,1.521 true 1.979,1.219 2.219,0.802 2.219,0.802 2.396,0.802 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.583,0.427 2.042,0.625 0.458,0.198 10 false A57 0.854,1.771 1.01,1.969 0.156,0.198 10 false E 2.458,0.729 2.771,0.927 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Headlight Cleaner Control Relay)


Disconnect the headlight cleaner control relay connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-4 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A57-3 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY AND BATTERY)
a.

Disconnect the A58 headlight cleaner motor and pump assembly connector.


b.

Disconnect the A57 headlight cleaner control relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-1 - A57-6 (PB) Always Below 1 Ω
A58-1 or A57-6 (PB) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)
a.

Disconnect the G80 headlight leveling ECU assembly connector.


b.

Disconnect the A57 headlight cleaner control relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-16 (HLC) - A57-2 (H) Always Below 1 Ω
G80-16 (HLC) or A57-2 (H) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - WINDSHIELD WIPER SWITCH ASSEMBLY)
a.

Disconnect the G80 headlight light leveling ECU assembly connector.


b.

Disconnect the G18 windshield wiper switch assembly connector.


c.

Disconnect the A2 windshield washer motor and pump assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-4 (FRWA) - G18-7 (WF) Always Below 1 Ω
G80-4 (FRWA) or G18-7 (WF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR