Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3250E _58 Vehicle Interior _038065 THEFT DETERRENT / KEYLESS ENTRY _0185023 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2282 Vehicle Speed Signal Malfunction The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

SMART fuse

·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.
B2283 Vehicle Speed Sensor Malfunction Either of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*)
·

Vehicle speed signal malfunction detection 1: Excessive deceleration is detected

·

Vehicle speed signal malfunction detection 2: Engine speed linked detection


·

SMART fuse

·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


Run the engine at an engine speed of 2000 rpm or more for 330 seconds.

*: Only detected while a malfunction is present and the engine switch is on (IG).


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.

·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine switch cannot be turned from on (IG) to off.


-
B2283
·

The power source mode is changed to off (the engine is stopped) by pressing the engine switch while the vehicle is being driven.

·

With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start.


Steering lock motor operation is prohibited.

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2282
B2283
Power Source Control
·

Engine Condition

·

Vehicle Speed Signal

·

Power Supply Condition


Starting Control
·

Engine Speed


Combination Meter
·

Vehicle Speed Meter


-

WIRING DIAGRAM

C326202E03
1.323,0.771 2.177,0.979 0.854,0.208 10 false from Battery 3,0.917 3.771,1.115 0.771,0.198 10 false SMART 4.104,0.667 4.26,0.865 0.156,0.198 10 false 1 4.323,0.76 4.635,0.958 0.313,0.198 10 false +B 1.938,1.271 2.25,1.469 0.313,0.198 10 false +S 1.083,2.5 1.396,2.698 0.313,0.198 10 false G9 1.083,2.646 2.948,2.875 1.865,0.229 10 false Combination Meter Assembly 0.688,3.385 2.5,3.594 1.813,0.208 10 false : CAN Communication Line 4.125,2.479 4.583,2.677 0.458,0.198 10 false G69 4.135,2.625 5.677,2.99 1.542,0.365 10 false Certification ECU (Smart Key ECU Assembly) 4.313,1.281 4.771,1.479 0.458,0.198 10 false SPD 2.26,1.26 2.573,1.458 0.313,0.198 10 false 19 4.115,1.271 4.271,1.469 0.156,0.198 10 false 7 5.115,2.156 5.271,2.354 0.156,0.198 10 false E 4.969,1.51 5.281,1.708 0.313,0.198 10 false IC 5.354,2.042 5.667,2.24 0.313,0.198 10 false 10 4.604,0.917 4.917,1.115 0.313,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the GTS read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0, Max.: 255 Almost same as actual vehicle speed (Speedometer tester) -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
HINT:

Using a speedometer tester, check the actual vehicle speed and the vehicle speed displayed on the GTS.


OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)

NG

GO TO METER / GAUGE SYSTEM (SPEEDOMETER MALFUNCTION)

2.READ VALUE USING GTS (VEHICLE SPEED SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Speed Signal
50003 223 16
OK:

Stop (vehicle is stopped) and Run (vehicle is moving) appear on the screen.



Result:
Proceed to
OK
NG



OK

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-7 (SPD) - G9-19 (+S) Always Below 1 Ω
G69-7 (SPD) or G9-19 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G69 certification ECU (smart key ECU assembly) connector.


b.

Connect the G9 combination meter assembly connector.


c.

Using an oscilloscope, check the waveform.


d.

Check the signal waveform according to the condition(s) in the table below.

C336313C01
2.167,0.104 2.615,0.354 0.448,0.25 2.229,2.146 2.073,2.146 2.073,2.146 2.073,1.052 true 1.427,2.208 1.604,2.208 1.604,2.208 1.833,1.052 true 0.219,0.073 0.531,0.271 0.313,0.198 10 false *a 2.26,0.146 2.719,0.344 0.458,0.198 10 false G69 4.563,2.969 5.021,3.167 0.458,0.198 10 false GND 2.26,2.083 2.719,2.281 0.458,0.198 10 false SPD 1.313,2.146 1.49,2.354 0.177,0.208 10 false E
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Frequency:
Tester Connection Condition Tool Setting Specified Condition
G69-7 (SPD) - G69-10 (E) Vehicle being driven at approx. 5 km/h (3 mph) 5 V/DIV., 200 ms./DIV. Pulse generation


HINT:

The wavelength becomes shorter as the vehicle speed increases.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO METER / GAUGE SYSTEM (SPEED SIGNAL CIRCUIT)