Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2015.06–2016.03
RM3250E _57 Power Source / Network _038063 NETWORKING _0186538 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area

*1: w/ VSC

*2: for Automatic Air Conditioning System or for Manual Air Conditioning System (w/ PTC Heater)

*3: w/ Entry and Start System

*4: for 4WD

*5: w/ Audio and Visual System (for Radio and Display Type)

*6: w/ Navigation System

*7: for LED Headlight

The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

ECM

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)*1

·

Air conditioning amplifier assembly*2

·

Airbag sensor assembly

·

Certification ECU (smart key ECU assembly)*3

·

4 wheel drive control ECU*4

·

Radio and display receiver assembly*5

·

Navigation receiver assembly*6

·

Headlight leveling ECU assembly*7

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C329350E01
6.188,2.531 6.646,2.729 0.458,0.198 10 false ECM 6.063,1.396 6.677,1.594 0.615,0.198 10 false CANH 6.094,2.177 6.708,2.375 0.615,0.198 10 false CANL 3.604,1.365 3.76,1.563 0.156,0.198 10 false 5 3.604,1.906 3.833,2.104 0.229,0.198 10 false 15 2.615,1.365 2.771,1.563 0.156,0.198 10 false 3 2.542,1.885 2.771,2.083 0.229,0.198 10 false 13 3.583,3.406 3.74,3.604 0.156,0.198 10 false 4 2.594,3.406 2.75,3.604 0.156,0.198 10 false 7 3.583,4.333 3.74,4.531 0.156,0.198 10 false 6 3.563,3.927 3.792,4.125 0.229,0.198 10 false 14 2.573,3.927 2.802,4.125 0.229,0.198 10 false 17 3.552,4.708 3.781,4.906 0.229,0.198 10 false 16 6.031,3.51 6.646,3.708 0.615,0.198 10 false CANH 6.073,4.073 6.688,4.271 0.615,0.198 10 false CANL 0.865,1.5 1.479,1.698 0.615,0.198 10 false CANH 0.906,2.031 1.521,2.229 0.615,0.198 10 false CANL 0.854,3.563 1.469,3.76 0.615,0.198 10 false CANH 0.896,4.094 1.51,4.292 0.615,0.198 10 false CANL 1.458,1.375 1.688,1.573 0.229,0.198 10 false 40 1.448,1.906 1.677,2.104 0.229,0.198 10 false 18 5.688,3.938 5.917,4.135 0.229,0.198 10 false 40 5.688,3.406 5.917,3.604 0.229,0.198 10 false 20 0.083,2.281 0.458,2.49 0.375,0.208 10 false G70 0.104,2.479 2.292,2.906 2.188,0.427 10 false Certification ECU (Smart Key ECU Assembly)*5 0.063,4.51 2.573,5.156 2.51,0.646 10 false Radio and Display Receiver Assembly*7, Navigation Receiver Assembly*8 5.292,4.344 5.667,4.552 0.375,0.208 10 false C39 5.302,4.552 7.156,4.823 1.854,0.271 10 false 4 Wheel Drive Control ECU*6 4.354,1.521 4.729,1.729 0.375,0.208 10 false G45 4.75,1.51 5.125,1.719 0.375,0.208 10 false G85 5.188,1.51 5.563,1.719 0.375,0.208 10 false G88 5.615,1.51 5.99,1.719 0.375,0.208 10 false G83 4.344,2.042 4.719,2.25 0.375,0.208 10 false G45 4.76,2.031 5.135,2.24 0.375,0.208 10 false G85 5.188,2.042 5.563,2.25 0.375,0.208 10 false G88 5.604,2.031 5.979,2.24 0.375,0.208 10 false G83 4.302,1.25 4.667,1.469 0.365,0.219 10 false 13*1 4.292,1.792 4.656,2.01 0.365,0.219 10 false 14*1 4.719,1.26 5.083,1.479 0.365,0.219 10 false 17*2 5.146,1.26 5.51,1.479 0.365,0.219 10 false 31*3 5.573,1.25 5.938,1.469 0.365,0.219 10 false 24*4 5.594,1.792 5.958,2.01 0.365,0.219 10 false 23*4 5.156,1.792 5.521,2.01 0.365,0.219 10 false 25*3 4.729,1.781 5.094,2 0.365,0.219 10 false 28*2 1.438,3.552 1.896,3.75 0.458,0.198 10 false G37 1.438,4.083 1.896,4.281 0.458,0.198 10 false G37 1.458,3.313 1.823,3.531 0.365,0.219 10 false 9*7 1.438,3.813 1.802,4.031 0.365,0.219 10 false 10*7 1.865,3.302 2.229,3.521 0.365,0.219 10 false 9*8 1.844,3.823 2.208,4.042 0.365,0.219 10 false 10*8 1.823,3.542 2.281,3.74 0.458,0.198 10 false G113 1.833,4.073 2.292,4.271 0.458,0.198 10 false G113 0.229,6.313 2.083,6.583 1.854,0.271 10 false *1: for 2TR-FE 0.229,6.656 2.083,6.927 1.854,0.271 10 false *2: for 1GD-FTV, 2GD-FTV 0.229,7.031 2.083,7.302 1.854,0.271 10 false *3: for 1GR-FE 0.208,7.385 2.063,7.656 1.854,0.271 10 false *4: for 1KD-FTV, 2KD-FTV 3.26,6.354 5.24,6.625 1.979,0.271 10 false *5: w/ Entry and Start System 3.25,6.698 5.229,6.969 1.979,0.271 10 false *6: for 4WD 3.26,7.073 7.063,7.333 3.802,0.26 10 false *7: w/ Audio and Visual System (for Radio and Display Type) 3.25,7.458 4.958,7.688 1.708,0.229 10 false *8: w/ Navigation System 2.438,5.167 2.813,5.375 0.375,0.208 10 false G68 2.469,5.344 3.74,5.781 1.271,0.438 10 false No. 2 CAN Junction Connector

C329351E01
4.167,0.479 4.323,0.677 0.156,0.198 10 false 6 4.146,0.781 4.458,0.979 0.313,0.198 10 false 16 4.156,1.313 4.365,1.552 0.208,0.24 10 false 1 4.167,1.813 4.479,2.01 0.313,0.198 10 false 11 3.167,1.302 3.323,1.5 0.156,0.198 10 false 2 3.188,3.323 3.344,3.521 0.156,0.198 10 false 4 4.167,3.302 4.323,3.5 0.156,0.198 10 false 3 3.115,1.833 3.427,2.031 0.313,0.198 10 false 12 3.115,3.854 3.427,4.052 0.313,0.198 10 false 14 4.135,3.865 4.448,4.063 0.313,0.198 10 false 13 4.156,5.813 4.469,6.01 0.313,0.198 10 false 18 4.167,5.271 4.427,5.615 0.26,0.344 10 false 8 3.125,5.271 3.438,5.469 0.313,0.198 10 false 10 3.135,5.802 3.448,6 0.313,0.198 10 false 20 4.177,7.167 4.333,7.365 0.156,0.198 10 false 5 4.156,7.708 4.469,7.906 0.313,0.198 10 false 15 6,1.438 6.615,1.635 0.615,0.198 10 false CANH 6.01,1.948 6.625,2.146 0.615,0.198 10 false CANL 0.885,1.427 1.5,1.625 0.615,0.198 10 false CANH 0.927,1.948 1.542,2.146 0.615,0.198 10 false CANL 5.24,1.427 5.552,1.625 0.313,0.198 10 false A3 5.24,1.958 5.552,2.156 0.313,0.198 10 false A3 5.656,1.427 5.969,1.625 0.313,0.198 10 false A4 5.656,1.948 5.969,2.146 0.313,0.198 10 false A4 5.177,1.198 5.563,1.396 0.385,0.198 10 false 25*1 5.156,1.729 5.542,1.927 0.385,0.198 10 false 14*1 5.594,1.198 5.979,1.396 0.385,0.198 10 false 22*2 5.594,1.729 5.979,1.927 0.385,0.198 10 false 10*2 1.469,1.302 1.781,1.5 0.313,0.198 10 false 13 1.469,1.813 1.781,2.01 0.313,0.198 10 false 22 5.51,2.375 7.104,2.833 1.594,0.458 10 false Brake Actuator Assembly (Skid Control ECU) 0.104,2.385 1.833,2.844 1.729,0.458 10 false Airbag Sensor Assembly 0.083,2.198 0.396,2.396 0.313,0.198 10 false G42 5.708,3.302 5.865,3.5 0.156,0.198 10 false 3 5.698,3.823 5.854,4.021 0.156,0.198 10 false 2 6.01,3.448 6.625,3.646 0.615,0.198 10 false CANH 6.01,3.969 6.625,4.167 0.615,0.198 10 false CANL 4.729,4.375 7.146,4.74 2.417,0.365 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*2 4.75,4.198 5.063,4.396 0.313,0.198 10 false G21 0.729,4.427 1.042,4.625 0.313,0.198 10 false G8 0.677,4.635 1.125,4.99 0.448,0.354 10 false DLC3 0.875,3.458 1.49,3.656 0.615,0.198 10 false CANH 0.906,3.99 1.521,4.188 0.615,0.198 10 false CANL 1.438,3.323 1.594,3.521 0.156,0.198 10 false 6 1.438,3.833 1.75,4.031 0.313,0.198 10 false 14 6.01,5.396 6.625,5.594 0.615,0.198 10 false CANH 6.021,5.927 6.635,6.125 0.615,0.198 10 false CANL 5.719,5.271 5.875,5.469 0.156,0.198 10 false 6 5.708,5.802 5.865,6 0.156,0.198 10 false 7 1.448,5.375 1.906,5.573 0.458,0.198 10 false G33 1.469,5.917 1.927,6.115 0.458,0.198 10 false G33 1.875,5.396 2.333,5.594 0.458,0.198 10 false G77 1.865,5.927 2.323,6.125 0.458,0.198 10 false G77 1.438,5.156 1.823,5.354 0.385,0.198 10 false 11*3 1.438,5.677 1.823,5.875 0.385,0.198 10 false 12*3 1.896,5.156 2.281,5.354 0.385,0.198 10 false 8*4 1.896,5.677 2.281,5.875 0.385,0.198 10 false 9*4 1.042,5.385 1.5,5.583 0.458,0.198 10 false TX+ 1.063,5.917 1.521,6.115 0.458,0.198 10 false TX- 0.094,6.354 2.51,6.719 2.417,0.365 10 false Air Conditioning Amplifier Assembly 6.021,7.156 6.635,7.354 0.615,0.198 10 false CANH 6.042,7.969 6.656,8.167 0.615,0.198 10 false CANL 5.625,7.167 5.938,7.365 0.313,0.198 10 false 36 5.625,7.698 5.938,7.896 0.313,0.198 10 false 35 3,8.26 5.094,8.479 2.094,0.219 10 false No. 1 CAN Junction Connector 3,8.063 3.365,8.26 0.365,0.198 10 false G67 0.094,6.927 1.625,7.125 1.531,0.198 10 false *1: w/o VSC 0.115,7.229 1.646,7.427 1.531,0.198 10 false *2: w/ VSC 4.823,6.469 7.135,6.729 2.313,0.26 10 false Headlight Leveling ECU Assembly*5 0.125,7.521 2.708,7.729 2.583,0.208 10 false *3: for Automatic Air Conditioning System 0.135,7.823 2.531,8.188 2.396,0.365 10 false *4: for Manual Air Conditioning System (w/ PTC Heater) 0.146,8.427 1.906,8.646 1.76,0.219 10 false *5: for LED Headlight 4.813,6.313 5.271,6.51 0.458,0.198 10 false G80 5.177,8.219 5.635,8.417 0.458,0.198 10 false G9 5.188,8.385 7.042,8.646 1.854,0.26 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the service bulletin.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

·

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
a.
C300827C24
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 2.052,1.906 2.052,1.906 2.167,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.052 0.5,1.219 0.281,0.167 10 false G8 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 2.229,1.844 2.844,2.042 0.615,0.198 10 false CANL
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)
3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C300827C24
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 2.052,1.906 2.052,1.906 2.167,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.052 0.5,1.219 0.281,0.167 10 false G8 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 2.229,1.844 2.844,2.042 0.615,0.198 10 false CANL
*a Front view of DLC3


Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)

NG

21.CONNECT CONNECTOR
4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

C300828C65
3.344,0.208 3.75,0.479 0.406,0.271 3.979,0.844 4.792,0.271 4.792,0.271 4.958,0.271 true 3.969,1.021 4.74,1.479 4.74,1.479 4.917,1.479 true 2.979,0.865 2.271,0.417 2.271,0.417 2.052,0.417 true 2.979,1.021 2.25,1.365 2.25,1.365 2.01,1.365 true 3.177,0.865 2.385,0.271 2.385,0.271 2.167,0.271 true 3.167,1.031 2.375,1.51 2.375,1.51 2.156,1.51 true 3.354,0.844 2.552,0.104 2.552,0.104 2.313,0.104 true 3.333,1.021 2.479,1.667 2.479,1.667 2.25,1.667 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 5,0.188 5.552,0.354 0.552,0.167 10 false CANH*e 1.5,0.333 2.031,0.479 0.531,0.146 10 false CANH*b 1.635,0.177 2.188,0.323 0.552,0.146 10 false CANH*c 1.781,0.031 2.323,0.198 0.542,0.167 10 false CANH*d 1.49,1.271 2.042,1.417 0.552,0.146 10 false CANL*b 1.615,1.417 2.188,1.573 0.573,0.156 10 false CANL*c 1.75,1.583 2.323,1.729 0.573,0.146 10 false CANL*d 4.969,1.406 5.5,1.552 0.531,0.146 10 false CANL*e 3.427,0.271 3.74,0.427 0.313,0.156 10 false G68
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*c to 4 Wheel Drive Control ECU (for 4WD) *d to ECM
*e
·

to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])

·

to Navigation Receiver Assembly (w/ Navigation System)


- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Entry and Start System

*2: for 4WD

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Navigation System

G68-3 (CANH) - G68-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (Smart Key ECU Assembly)*1
G68-4 (CANH) - G68-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4 Wheel Drive Control ECU*2
G68-5 (CANH) - G68-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
G68-7 (CANH) - G68-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Radio and Display Receiver Assembly*3

·

Navigation Receiver Assembly*4





Result:
Result Proceed to
OK A
NG (to certification ECU [smart key ECU assembly] CAN branch wire) (w/ Entry and Start System) B
NG (to 4 wheel drive control ECU CAN branch wire) (for 4WD) C
NG (to ECM CAN main wire) (for 2TR-FE) D
NG (to ECM CAN main wire) (for 1GR-FE) E
NG (to ECM CAN main wire) (for 1KD-FTV, 2KD-FTV) F
NG (to ECM CAN main wire) (for 1GD-FTV, 2GD-FTV) G
NG (to radio and display receiver assembly CAN branch wire) (w/ Audio and Visual System [for Radio and Display Type]) H
NG (to navigation receiver assembly CAN branch wire) (w/ Navigation System) I



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR

D

9.CONNECT CONNECTOR

E

11.CONNECT CONNECTOR

F

13.CONNECT CONNECTOR

G

15.CONNECT CONNECTOR

H

17.CONNECT CONNECTOR

I

19.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU BRANCH WIRE)
6.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU BRANCH WIRE)
a.
E271716C05
1.521,0.26 1.917,0.5 0.396,0.24 2.583,0.458 2.719,0.458 2.719,0.458 3.073,1.031 true 3.042,1.25 2.885,1.896 2.885,1.896 2.75,1.896 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.594,0.302 2.052,0.5 0.458,0.198 10 false G70 2.323,1.823 2.76,2.063 0.438,0.24 10 false CANH 2.198,0.385 2.635,0.625 0.438,0.24 10 false CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-40 (CANH) - G70-18 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

7.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT IN CAN BUS WIRES (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
8.CHECK FOR SHORT IN CAN BUS WIRES (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
C317101C02
1.5,0.177 1.917,0.458 0.417,0.281 2.906,1.021 2.771,0.385 2.771,0.385 2.625,0.385 true 2.604,1.823 2.76,1.823 2.76,1.823 2.906,1.292 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.573,0.229 2.031,0.427 0.458,0.198 10 false C39 2.188,0.292 2.802,0.49 0.615,0.198 10 false CANH 2.219,1.74 2.833,1.938 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-20 (CANH) - C39-40 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4 WHEEL DRIVE CONTROL ECU (CANH, CANL)

9.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
10.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
C317098C06
1.458,0.458 1.906,0.74 0.448,0.281 2.344,3.167 2.198,3.167 2.198,3.167 2.073,2 true 2.521,2.854 2.375,2.854 2.375,2.854 2.219,2.01 true 1.552,0.51 2.01,0.708 0.458,0.198 10 false G45 2.583,2.771 3.208,2.99 0.625,0.219 10 false CANL 2.427,3.063 3.052,3.302 0.625,0.24 10 false CANH 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-13 (CANH) - G45-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

11.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
12.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
C329346C01
2.344,0.938 2.813,1.229 0.469,0.292 0.854,1.969 0.99,1.969 0.99,1.969 1.292,1.573 true 0.813,1.042 0.948,1.042 0.948,1.042 1.292,1.375 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.406,1.885 0.854,2.083 0.448,0.198 10 false CANH 2.448,1.01 3.063,1.208 0.615,0.198 10 false G88 0.385,0.958 0.823,1.156 0.438,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-31 (CANH) - G88-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
14.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
C317098C07
1.458,0.823 1.906,1.104 0.448,0.281 0.688,1.521 0.833,1.521 0.833,1.521 2.063,2.083 true 0.688,3.135 0.833,3.135 0.833,3.135 1.938,2.167 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G83 0.271,1.458 0.75,1.656 0.479,0.198 10 false CANH 0.26,3.063 0.708,3.26 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-24 (CANH) - G83-23 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
16.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
C317098C10
1.458,0.823 1.906,1.104 0.448,0.281 0.667,1.885 0.813,1.885 0.813,1.885 1.063,2.094 true 0.677,2.906 0.823,2.906 0.823,2.906 1.073,2.344 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G85 0.208,1.792 0.688,1.99 0.479,0.198 10 false CANH 0.24,2.823 0.688,3.021 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-17 (CANH) - G85-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
18.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.
C310966C09
1.49,0.198 1.938,0.469 0.448,0.271 1.104,1.75 1.271,1.75 1.271,1.75 1.896,1.104 true 2.365,1.76 2.219,1.76 2.219,1.76 2.021,1.115 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.594,0.26 2.208,0.458 0.615,0.198 10 false G37 0.677,1.677 1.292,1.875 0.615,0.198 10 false CANH 2.438,1.698 3.052,1.896 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-9 (CANH) - G37-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
20.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.
C310966C10
1.49,0.198 1.938,0.469 0.448,0.271 1.104,1.75 1.271,1.75 1.271,1.75 1.896,1.104 true 2.365,1.76 2.219,1.76 2.219,1.76 2.021,1.115 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.563,0.24 2.177,0.438 0.615,0.198 10 false G113 0.656,1.656 1.271,1.854 0.615,0.198 10 false CANH 2.427,1.667 3.042,1.865 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-9 (CANH) - G113-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

21.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C300828C64
0.833,0.74 1.219,1 0.385,0.26 3.01,0.865 2.333,0.313 2.333,0.313 2.177,0.313 true 2.99,1.021 2.292,1.49 2.292,1.49 2.167,1.49 true 4.542,0.833 5.063,0.604 5.063,0.604 5.219,0.604 true 2.802,0.865 2.24,0.5 2.24,0.5 2.083,0.5 true 2.802,1.021 2.198,1.354 2.198,1.354 2.073,1.354 true 2.573,0.854 2.135,0.698 2.135,0.698 2,0.698 true 2.573,1.031 2.104,1.188 2.104,1.188 1.979,1.188 true 3.375,0.865 2.448,0.125 2.448,0.125 2.292,0.125 true 3.385,1.031 2.396,1.688 2.396,1.688 2.271,1.688 true 4.531,1.031 5.063,1.156 5.063,1.156 5.219,1.156 true 4.156,0.865 5.031,0.427 5.031,0.427 5.188,0.427 true 3.771,0.844 4.938,0.104 4.938,0.104 5.094,0.104 true 4.167,1.01 4.958,1.354 4.958,1.354 5.115,1.354 true 3.792,1.021 4.74,1.688 4.74,1.688 4.896,1.688 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 5.271,0.531 5.885,0.729 0.615,0.198 10 false CANH*h 5.24,0.344 5.833,0.594 0.594,0.25 10 false CANH*g 1.531,0.417 2.104,0.604 0.573,0.188 10 false CANH*c 1.604,0.229 2.167,0.427 0.563,0.198 10 false CANH*d 1.74,0.042 2.344,0.24 0.604,0.198 10 false CANH*e 1.552,1.271 2.083,1.458 0.531,0.188 10 false CANL*c 1.625,1.427 2.24,1.615 0.615,0.188 10 false CANL*d 1.75,1.604 2.396,1.76 0.646,0.156 10 false CANL*e 5.156,1.292 5.76,1.479 0.604,0.188 10 false CANL*g 5.25,1.083 5.865,1.292 0.615,0.208 10 false CANL*h 5.135,0.031 5.74,0.25 0.604,0.219 10 false CANH*f 4.979,1.615 5.635,1.781 0.656,0.167 10 false CANL*f 1.448,0.625 2.042,0.865 0.594,0.24 10 false CANH*b 1.427,1.094 2.031,1.292 0.604,0.198 10 false CANL*b 0.906,0.792 1.219,0.948 0.313,0.156 10 false G67
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Brake Actuator Assembly (Skid Control ECU)
*c to Airbag Sensor Assembly *d to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC)
*e to Combination Meter Assembly *f to No. 2 CAN Junction Connector
*g to Headlight Leveling ECU Assembly (for LED Headlight) *h
·

to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)

·

to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System [w/ PTC Heater])





b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ VSC

*2: for LED Headlight

*3: for Automatic Air Conditioning System

*4: for Manual Air Conditioning System (w/ PTC Heater)

G67-1 (CANH) - G67-11 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake Actuator Assembly (Skid Control ECU)
G67-2 (CANH) - G67-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag Sensor Assembly
G67-3 (CANH) - G67-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*1
G67-5 (CANH) - G67-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination Meter Assembly
G67-6 (CANH) - G67-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN Junction Connector
G67-8 (CANH) - G67-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight Leveling ECU Assembly*2
G67-10 (CANH) - G67-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air Conditioning Amplifier Assembly*3, *4



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid Control ECU] CAN branch wire) B
NG (to airbag sensor assembly CAN branch wire) C
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) (w/ VSC) D
NG (to combination meter assembly CAN main wire) E
NG (to headlight leveling ECU assembly CAN branch wire) (for LED Headlight) F
NG (to air conditioning amplifier assembly CAN branch wire) (for Automatic Air Conditioning System) G
NG (to air conditioning amplifier assembly CAN branch wire) (for Manual Air Conditioning System [w/ PTC Heater]) H
NG (to No. 2 CAN junction connector CAN main wire) I



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

23.CONNECT CONNECTOR

C

25.CONNECT CONNECTOR

D

27.CONNECT CONNECTOR

E

29.CONNECT CONNECTOR

F

31.CONNECT CONNECTOR

G

33.CONNECT CONNECTOR

H

35.CONNECT CONNECTOR

I

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

23.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU BRANCH WIRE)
24.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU BRANCH WIRE)
a.
C317099C01
1.448,2.479 1.896,2.771 0.448,0.292 1.458,0.125 1.906,0.417 0.448,0.292 2.094,0.854 2.365,0.313 2.365,0.313 2.51,0.313 true 2.094,1.021 2.344,1.854 2.344,1.854 2.51,1.854 true 0.594,4.417 0.75,4.417 0.75,4.417 1.302,3.688 true 0.531,2.708 0.688,2.708 0.688,2.708 1.292,3.573 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.583,1.76 3.198,1.958 0.615,0.198 10 false CANH 2.594,0.219 3.208,0.417 0.615,0.198 10 false CANL 0.167,4.333 0.781,4.531 0.615,0.198 10 false CANH 0.146,2.646 0.76,2.844 0.615,0.198 10 false CANL 1.604,0.177 1.917,0.375 0.313,0.198 10 false A4 1.594,2.531 1.906,2.729 0.313,0.198 10 false A3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.958,2.542 2.271,2.74 0.313,0.198 10 false *B
*A w/ VSC
*B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
A4-22 (CANH) - A4-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/o VSC
Tester Connection Condition Specified Condition
A3-25 (CANH) - A3-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
26.CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.
C210016C17
0.302,1 0.75,1.302 0.448,0.302 1.99,1.052 2.198,0.448 2.198,0.448 2.333,0.448 true 2.094,1.323 2.271,1.698 2.271,1.698 2.417,1.698 true 0.052,0.063 0.24,0.24 0.188,0.177 10 false *a 2.375,0.375 2.813,0.552 0.438,0.177 10 false CANH 0.375,1.073 0.656,1.25 0.281,0.177 10 false G42 2.458,1.615 2.896,1.792 0.438,0.177 10 false CANL
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the airbag sensor assembly connector.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G42-13 (CANH) - G42-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE)
28.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE)
a.
C300837C17
0.51,0.865 0.938,1.167 0.427,0.302 2.208,1.677 2.052,1.677 2.052,1.677 1.708,1.208 true 1.01,1.708 1.188,1.708 1.188,1.708 1.531,1.219 true 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 0.615,0.948 0.927,1.125 0.313,0.177 10 false G21 2.25,1.615 2.677,1.781 0.427,0.167 10 false CANH 0.667,1.635 1.125,1.792 0.458,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G21-3 (CANH) - G21-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (CANH, CANL)

29.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

30.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY MAIN WIRE)
30.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY MAIN WIRE)
a.
C221258C12
1.521,0.333 1.927,0.615 0.406,0.281 1.125,1.979 1.292,1.979 1.292,1.979 1.385,1.354 true 0.917,1.76 1.063,1.76 1.063,1.76 1.313,1.333 true 0.073,0.052 0.24,0.24 0.167,0.188 10 false *a 0.49,1.688 0.917,1.844 0.427,0.156 10 false CANH 0.708,1.906 1.104,2.063 0.396,0.156 10 false CANL 1.625,0.385 1.948,0.573 0.323,0.188 10 false G9
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-36 (CANH) - G9-35 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

31.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

32.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
32.CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
a.
C317100C05
1.458,0.24 1.906,0.542 0.448,0.302 2.375,1.052 2.51,0.469 2.51,0.469 2.635,0.469 true 1.927,1.844 2.073,1.844 2.073,1.844 2.25,1.135 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.563,0.313 2.021,0.51 0.458,0.198 10 false G80 1.469,1.76 1.938,1.969 0.469,0.208 10 false CANH 2.708,0.385 3.323,0.583 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Disconnect the headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-6 (CANH) - G80-7 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT LEVELING ECU ASSEMBLY (CANH, CANL)

33.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
34.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C240157C57
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.344,1.063 0.802,1.26 0.458,0.198 10 false G33 2.333,0.406 2.792,0.604 0.458,0.198 10 false TX+ 2.24,0.156 2.698,0.354 0.458,0.198 10 false TX-
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-11 (TX+) - G33-12 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

35.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
36.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
E273494C09
1.563,0.333 1.958,0.583 0.396,0.25 2.469,1.083 1.708,1.833 1.708,1.833 1.563,1.833 true 2.625,1.094 2.344,2.01 2.344,2.01 2.219,2.01 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.646,0.354 2.104,0.552 0.458,0.198 10 false G77 1.271,1.74 1.583,1.938 0.313,0.198 10 false TX+ 1.948,1.927 2.26,2.125 0.313,0.198 10 false TX-
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-8 (TX+) - G77-9 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)