1.REMOVE FRONT SEAT ASSEMBLY RH (for RHD)
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL
2.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
The procedure described below is for the RH side.
for Power Seat:
The procedure described below is for the RH side.
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL
3.REMOVE REAR SEAT ASSEMBLY
for Seat Cushion 60/40 Split Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Seat Cushion 60/40 Split Type)>REMOVAL
for Seat Cushion Bench Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Seat Cushion Bench Type)>REMOVAL
58810J
4.REMOVE CONSOLE BOX ASSEMBLY (for RHD, w/ Console Box Lid)
58901A
5.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (for RHD, w/ Rear Console Box)
67914B
6.REMOVE FRONT DOOR SCUFF PLATE LH
67913B
7.REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)
62111C
8.REMOVE COWL SIDE TRIM BOARD RH (for RHD)
62112
9.REMOVE COWL SIDE TRIM BOARD LH (for LHD)
67918E
10.REMOVE REAR DOOR SCUFF PLATE LH
62414A
11.REMOVE LOWER CENTER PILLAR GARNISH LH
62514A
12.REMOVE LOWER QUARTER TRIM PANEL LH
58510D
13.REMOVE FRONT FLOOR CARPET ASSEMBLY
Partially remove the floor carpet.
It is not necessary to fully remove the floor carpet. Partially remove it so that the fuel lid lock control cable sub-assembly can be removed in a later step.
65638
14.REMOVE REAR WHEEL HOUSE LINER LH
Partially remove the liner.
It is not necessary to fully remove the liner. Partially remove it so that the fuel lid lock control cable sub-assembly can be removed in a later step.
77306
15.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for LHD)
Detach the claw and remove the fuel lid lock open lever sub-assembly.
77306
16.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for RHD)
Detach the claw and remove the fuel lid lock open lever sub-assembly.
77035
17.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)
Remove the grommet from the vehicle body.
Detach each clamp as shown in the illustration.
| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Grommet |
|
Remove in this Direction |
Detach the claw and remove the fuel lid lock control cable sub-assembly from the fuel filler opening lid lock retainer as shown in the illustration.
77035
18.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)
Remove the grommet from the vehicle body.
Detach each clamp as shown in the illustration.
| *A | for 4WD and Pre-Runner without VSC | - | - |
| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Grommet |
|
Remove in this Direction |
Detach the claw and remove the fuel lid lock control cable sub-assembly from the fuel filler opening lid lock retainer as shown in the illustration.
77377
19.REMOVE FUEL FILLER OPENING LID LOCK RETAINER
| *a | 90° |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
Remove the fuel filler opening lid lock retainer as shown in the illustration.