Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2015.06–2016.01
RM3250E _57 Power Source / Network _038063 NETWORKING _0189612 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Short to GND in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Symptom Trouble Area

*1: w/ VSC

*2: for Automatic Air Conditioning System or for Manual Air Conditioning System (w/ PTC Heater)

*3: w/ Entry and Start System

*4: for 4WD

*5: w/ Audio and Visual System (for Radio and Display Type)

*6: w/ Navigation System

*7: for LED Headlight or w/ Headlight Cleaner System

*8: w/ Airbag System

The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
·

Short between CAN bus lines and GND

·

ECM

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)*1

·

Air conditioning amplifier assembly*2

·

Airbag sensor assembly*8

·

Certification ECU (smart key ECU assembly)*3

·

4 wheel drive control ECU*4

·

Radio and display receiver assembly*5

·

Navigation receiver assembly*6

·

Headlight leveling ECU assembly*7

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C329364E01
6.073,0.677 6.688,0.875 0.615,0.198 10 false CANH 6.073,1.479 6.688,1.677 0.615,0.198 10 false CANL 6.063,2.844 6.677,3.042 0.615,0.198 10 false CANH 6.083,3.385 6.698,3.583 0.615,0.198 10 false CANL 0.875,0.813 1.49,1.01 0.615,0.198 10 false CANH 0.885,1.333 1.5,1.531 0.615,0.198 10 false CANL 0.885,2.844 1.5,3.042 0.615,0.198 10 false CANH 0.896,3.375 1.51,3.573 0.615,0.198 10 false CANL 0.958,5.177 1.313,5.375 0.354,0.198 10 false TX+ 0.958,5.729 1.313,5.927 0.354,0.198 10 false TX- 4.781,0.802 5.24,1 0.458,0.198 10 false G45 4.771,1.344 5.229,1.542 0.458,0.198 10 false G45 5.188,0.802 5.646,1 0.458,0.198 10 false G85 5.188,1.323 5.646,1.521 0.458,0.198 10 false G85 5.615,0.802 6.073,1 0.458,0.198 10 false G83 5.604,1.333 6.063,1.531 0.458,0.198 10 false G83 4.771,0.563 5.115,0.781 0.344,0.219 10 false 13*1 4.75,1.115 5.094,1.333 0.344,0.219 10 false 14*1 5.188,0.563 5.531,0.781 0.344,0.219 10 false 17*2 5.188,1.104 5.531,1.323 0.344,0.219 10 false 28*2 5.594,0.563 5.938,0.781 0.344,0.219 10 false 24*3 5.604,1.115 5.948,1.333 0.344,0.219 10 false 23*3 1.448,0.688 1.76,0.885 0.313,0.198 10 false 40 1.458,1.198 1.771,1.396 0.313,0.198 10 false 18 1.448,2.833 1.906,3.031 0.458,0.198 10 false G37 1.448,3.375 1.906,3.573 0.458,0.198 10 false G37 1.833,2.833 2.292,3.031 0.458,0.198 10 false G113 1.833,3.375 2.292,3.573 0.458,0.198 10 false G113 1.438,2.625 1.771,2.792 0.333,0.167 10 false 9*5 1.885,2.625 2.219,2.792 0.333,0.167 10 false 9*6 1.438,3.167 1.771,3.333 0.333,0.167 10 false 10*5 1.844,3.167 2.177,3.333 0.333,0.167 10 false 10*6 5.677,3.229 5.938,3.438 0.26,0.208 10 false 40 5.677,2.698 5.938,2.906 0.26,0.208 10 false 20 3.667,0.635 3.927,0.844 0.26,0.208 10 false 5 3.635,1.156 3.896,1.365 0.26,0.208 10 false 15 2.604,0.656 2.865,0.865 0.26,0.208 10 false 3 2.552,1.177 2.813,1.385 0.26,0.208 10 false 13 3.594,2.688 3.854,2.896 0.26,0.208 10 false 4 3.594,3.177 3.854,3.385 0.26,0.208 10 false 14 2.594,2.719 2.854,2.927 0.26,0.208 10 false 7 2.563,3.229 2.823,3.438 0.26,0.208 10 false 17 3.615,5.01 3.875,5.219 0.26,0.208 10 false 6 3.573,5.552 3.833,5.76 0.26,0.208 10 false 16 2.573,5.042 2.833,5.25 0.26,0.208 10 false 10 2.563,5.573 2.823,5.781 0.26,0.208 10 false 20 6.177,1.823 6.635,2.021 0.458,0.198 10 false ECM 0.135,1.594 0.594,1.792 0.458,0.198 10 false G70 0.125,1.792 2.281,2.167 2.156,0.375 10 false Certification ECU (Smart Key ECU Assembly)*4 0.104,3.823 2.625,4.219 2.521,0.396 10 false Radio and Display Receiver Assembly*5, Navigation Receiver Assembly*6 5.208,3.635 5.667,3.833 0.458,0.198 10 false C39 5.208,3.833 7.125,4.167 1.917,0.333 10 false 4 Wheel Drive Control ECU*7 0.115,6.188 1.688,6.552 1.573,0.365 10 false Air Conditioning Amplifier Assembly 1.448,5.188 1.906,5.385 0.458,0.198 10 false G33 1.458,5.729 1.917,5.927 0.458,0.198 10 false G33 1.875,5.198 2.333,5.396 0.458,0.198 10 false G77 1.875,5.719 2.333,5.917 0.458,0.198 10 false G77 1.427,4.958 1.771,5.135 0.344,0.177 10 false 11*8 1.427,5.49 1.771,5.667 0.344,0.177 10 false 12*8 1.896,5.51 2.24,5.688 0.344,0.177 10 false 9*4 1.885,4.969 2.229,5.146 0.344,0.177 10 false 8*9 2.281,6.302 3.563,6.688 1.281,0.385 10 false No. 2 CAN Junction Connector 2.281,6.104 2.74,6.302 0.458,0.198 10 false G68 0.052,7.01 1.667,7.24 1.615,0.229 10 false *1: for 1TR-FE, 2TR-FE 0.073,7.344 1.927,7.573 1.854,0.229 10 false *2: for 1GD-FTV, 2GD-FTV 0.094,7.698 1.948,7.927 1.854,0.229 10 false *3: for 1KD-FTV, 2KD-FTV 0.104,8.031 2.073,8.271 1.969,0.24 10 false *4: w/ Entry and Start System 3.573,7.271 4.573,7.51 1,0.24 10 false *7: for 4WD 0.115,8.406 3.896,8.656 3.781,0.25 10 false *5: w/ Audio and Visual System (for Radio and Display Type) 3.563,6.927 5.479,7.177 1.917,0.25 10 false *6: w/ Navigation System 3.573,7.656 6.396,7.958 2.823,0.302 10 false *8: for Automatic Air Conditioning System 3.573,8.01 7.073,8.302 3.5,0.292 10 false *9: for Manual Air Conditioning System (w/ PTC Heater)

C329363E02
5.396,2.375 6.99,2.771 1.594,0.396 10 false Brake Actuator Assembly (Skid Control ECU) 6.021,1.417 6.594,1.594 0.573,0.177 10 false CANH 6.031,1.99 6.604,2.167 0.573,0.177 10 false CANL 6.042,3.458 6.615,3.635 0.573,0.177 10 false CANH 6.031,3.99 6.604,4.167 0.573,0.177 10 false CANL 6.073,5.292 6.646,5.469 0.573,0.177 10 false CANH 6.073,6.063 6.646,6.24 0.573,0.177 10 false CANL 0.896,1.438 1.469,1.615 0.573,0.177 10 false CANH 0.927,1.958 1.5,2.135 0.573,0.177 10 false CANL 0.948,3.99 1.521,4.167 0.573,0.177 10 false CANL 0.896,3.458 1.469,3.635 0.573,0.177 10 false CANH 0.906,5.406 1.479,5.583 0.573,0.177 10 false CANH 0.885,5.938 1.458,6.115 0.573,0.177 10 false CANL 5.219,1.427 5.49,1.615 0.271,0.188 10 false A3 5.219,1.969 5.49,2.156 0.271,0.188 10 false A3 5.646,1.417 5.917,1.604 0.271,0.188 10 false A4 5.646,1.958 5.917,2.146 0.271,0.188 10 false A4 4.177,0.458 4.333,0.656 0.156,0.198 10 false 6 4.146,0.75 4.417,0.948 0.271,0.198 10 false 16 4.188,1.292 4.344,1.49 0.156,0.198 10 false 1 3.177,1.292 3.333,1.49 0.156,0.198 10 false 2 3.156,3.26 3.313,3.458 0.156,0.198 10 false 4 4.188,3.292 4.344,3.49 0.156,0.198 10 false 3 4.156,5.26 4.313,5.458 0.156,0.198 10 false 5 3.167,5.26 3.323,5.458 0.156,0.198 10 false 8 4.156,1.813 4.427,2.01 0.271,0.198 10 false 11 3.104,1.823 3.375,2.021 0.271,0.198 10 false 12 3.094,3.854 3.365,4.052 0.271,0.198 10 false 14 3.104,5.792 3.375,5.99 0.271,0.198 10 false 18 4.135,5.802 4.406,6 0.271,0.198 10 false 15 4.156,3.844 4.427,4.042 0.271,0.198 10 false 13 1.438,1.292 1.708,1.49 0.271,0.198 10 false 13 1.458,1.823 1.729,2.021 0.271,0.198 10 false 22 5.719,3.271 5.875,3.469 0.156,0.198 10 false 3 5.708,3.833 5.865,4.031 0.156,0.198 10 false 2 1.49,3.292 1.646,3.49 0.156,0.198 10 false 6 1.479,3.823 1.75,4.021 0.271,0.198 10 false 14 1.479,5.229 1.635,5.427 0.156,0.198 10 false 6 1.479,5.771 1.635,5.969 0.156,0.198 10 false 7 5.688,5.271 5.958,5.469 0.271,0.198 10 false 36 5.688,5.792 5.958,5.99 0.271,0.198 10 false 35 5.146,1.198 5.469,1.396 0.323,0.198 10 false 25*1 5.146,1.719 5.469,1.917 0.323,0.198 10 false 14*1 5.583,1.188 5.906,1.385 0.323,0.198 10 false 22*2 5.573,1.729 5.896,1.927 0.323,0.198 10 false 10*2 0.104,2.219 0.458,2.417 0.354,0.198 10 false G42 0.094,2.385 1.948,2.781 1.854,0.396 10 false Airbag Sensor Assembly*4 0.781,4.438 1.135,4.635 0.354,0.198 10 false G8 0.708,4.604 1.146,4.917 0.438,0.313 10 false DLC3 4.729,4.229 5.083,4.427 0.354,0.198 10 false G21 4.74,4.417 7.156,4.833 2.417,0.417 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*2 0.063,6.385 2.417,6.615 2.354,0.229 10 false Headlight Leveling ECU Assembly*3 0.052,6.208 0.406,6.406 0.354,0.198 10 false G80 5.25,6.375 7.156,6.667 1.906,0.292 10 false Combination Meter Assembly 5.25,6.188 5.604,6.385 0.354,0.198 10 false G9 0.156,7.208 1.844,7.406 1.688,0.198 10 false *1: w/o VSC 0.167,7.573 1.854,7.771 1.688,0.198 10 false *2: w/ VSC 0.167,7.969 3.865,8.167 3.698,0.198 10 false *3: for LED Headlight or w/ Headlight Cleaner System 2.802,6.417 4.792,6.677 1.99,0.26 10 false No. 1 CAN Junction Connector 2.792,6.25 3.146,6.448 0.354,0.198 10 false G67 0.177,8.354 2.469,8.594 2.292,0.24 10 false *4: w/ Airbag System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the service bulletin.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

·

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C300827C26
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 2.156,0.385 2.156,0.385 2.365,0.385 true 1.938,1.49 1.781,1.906 1.781,1.906 1.594,1.906 true 1.573,0.938 1.469,0.448 1.469,0.448 1.292,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.229,1.052 0.448,1.26 0.219,0.208 10 false G8 2.427,0.344 2.917,0.49 0.49,0.146 10 false CANH 1.25,1.833 1.865,2.031 0.615,0.198 10 false CANL 0.99,0.385 1.333,0.542 0.344,0.156 10 false CG
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-14 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C300827C26
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 2.156,0.385 2.156,0.385 2.365,0.385 true 1.938,1.49 1.781,1.906 1.781,1.906 1.594,1.906 true 1.573,0.938 1.469,0.448 1.469,0.448 1.292,0.448 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.229,1.052 0.448,1.26 0.219,0.208 10 false G8 2.427,0.344 2.917,0.49 0.49,0.146 10 false CANH 1.25,1.833 1.865,2.031 0.615,0.198 10 false CANL 0.99,0.385 1.333,0.542 0.344,0.156 10 false CG
*a Front view of DLC3


Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G8-14 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)

NG

23.CONNECT CONNECTOR
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

C300844C64
1.958,0.198 2.365,0.458 0.406,0.26 5.49,0.135 5.896,0.396 0.406,0.26 1.573,0.854 1.031,0.531 1.031,0.531 0.875,0.531 true 1.76,0.854 1.219,0.344 1.219,0.344 1.063,0.344 true 1.583,1.021 1.073,1.313 1.073,1.313 0.917,1.313 true 1.781,1.031 1.24,1.479 1.24,1.479 1.083,1.479 true 2.594,0.844 3.073,0.104 3.073,0.104 3.188,0.104 true 2.573,1.021 2.896,1.656 2.896,1.656 3.01,1.656 true 5.604,0.792 5.167,1.5 5.167,1.5 5.01,1.5 true 1.969,1.031 1.396,1.656 1.396,1.656 1.24,1.656 true 1.969,0.875 1.292,0.167 1.292,0.167 1.135,0.167 true 3.146,0.865 3.396,0.49 3.396,0.49 3.51,0.49 true 3.125,1.01 3.344,1.344 3.344,1.344 3.458,1.344 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 4.49,0.146 4.802,0.344 0.313,0.198 10 false *b 0.333,0.448 0.896,0.604 0.563,0.156 10 false CANH*c 0.406,1.208 0.969,1.365 0.563,0.156 10 false CANL*c 0.51,0.26 1.073,0.417 0.563,0.156 10 false CANH*d 0.594,0.073 1.156,0.229 0.563,0.156 10 false CANH*e 0.563,1.385 1.125,1.542 0.563,0.156 10 false CANL*d 0.729,1.573 1.292,1.729 0.563,0.156 10 false CANL*e 3.24,0.042 3.823,0.25 0.583,0.208 10 false CANH*f 3.052,1.583 3.688,1.771 0.635,0.188 10 false CANL*f 2.042,0.26 2.333,0.427 0.292,0.167 10 false G68 5.604,0.188 5.844,0.375 0.24,0.188 10 false G8 4.729,1.427 5.073,1.583 0.344,0.156 10 false CG 3.583,0.396 4.167,0.604 0.583,0.208 10 false CANH*g 3.531,1.26 4.167,1.448 0.635,0.188 10 false CANL*g
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3
*c to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *d to 4 Wheel Drive Control ECU (for 4WD)
*e to ECM *f
·

to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])

·

to Navigation Receiver Assembly (w/ Navigation System)


*g
·

to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)

·

to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System [w/ PTC Heater])


- -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Entry and Start System

*2: for 4WD

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Navigation System

*5: for Automatic Air Conditioning System

*6: for Manual Air Conditioning System (w/ PTC Heater)

G68-3 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (Smart Key ECU Assembly)*1
G68-13 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G68-4 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4 Wheel Drive Control ECU*2
G68-14 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G68-5 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
G68-15 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G68-7 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Radio and Display Receiver Assembly*3

·

Navigation Receiver Assembly*4


G68-17 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G68-10 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air Conditioning Amplifier Assembly*5, *6
G68-20 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to certification ECU [smart key ECU assembly] CAN branch wire) (w/ Entry and Start System) B
NG (to 4 wheel drive control ECU CAN branch wire) (for 4WD) C
NG (to ECM CAN main wire) (for 1TR-FE, 2TR-FE) D
NG (to ECM CAN main wire) (for 1KD-FTV, 2KD-FTV) E
NG (to ECM CAN main wire) (for 1GD-FTV, 2GD-FTV) F
NG (to radio and display receiver assembly CAN branch wire) (w/ Audio and Visual System [for Radio and Display Type]) G
NG (to navigation receiver assembly CAN branch wire) (w/ Navigation System) H
NG (to air conditioning amplifier assembly CAN branch wire) (for Automatic Air Conditioning System) I
NG (to air conditioning amplifier assembly CAN branch wire) (for Manual Air Conditioning System [w/ PTC Heater]) J



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR

D

9.CONNECT CONNECTOR

E

11.CONNECT CONNECTOR

F

13.CONNECT CONNECTOR

G

15.CONNECT CONNECTOR

H

17.CONNECT CONNECTOR

I

19.CONNECT CONNECTOR

J

21.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU BRANCH WIRE)
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CERTIFICATION ECU BRANCH WIRE)
a.
C317104C04
1.417,2.521 1.896,2.813 0.479,0.292 1.458,0.125 1.938,0.417 0.479,0.292 3.094,1.052 2.833,0.427 2.833,0.427 2.677,0.427 true 3.063,1.26 2.875,2 2.875,2 2.719,2 true 1.573,3.229 1.052,2.802 1.052,2.802 0.896,2.802 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 0.094,2.438 0.406,2.594 0.313,0.156 10 false *b 1.573,0.188 2.031,0.385 0.458,0.198 10 false G70 1.573,2.583 2.031,2.781 0.458,0.198 10 false G8 0.615,2.719 1.073,2.917 0.458,0.198 10 false CG 2.281,1.927 2.771,2.188 0.49,0.26 10 false CANH 2.26,0.365 2.698,0.625 0.438,0.26 10 false CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
*b Front view of DLC3


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-40 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G70-18 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

7.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
C317105C04
1.458,0.198 1.917,0.469 0.458,0.271 1.344,2.552 1.802,2.823 0.458,0.271 2.948,1.198 2.833,0.531 2.833,0.531 2.677,0.531 true 2.948,1.438 2.875,2.021 2.875,2.021 2.719,2.021 true 1.583,3.24 0.958,2.823 0.958,2.823 0.802,2.823 true 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 0.125,2.521 0.438,2.677 0.313,0.156 10 false *b 1.563,0.25 2.021,0.448 0.458,0.198 10 false C39 1.5,2.615 1.958,2.813 0.458,0.198 10 false G8 2.313,1.948 2.74,2.208 0.427,0.26 10 false CANL 2.24,0.469 2.677,0.76 0.438,0.292 10 false CANH 0.521,2.75 1.135,2.948 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)
*b Front view of DLC3


Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-20 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
C39-40 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4 WHEEL DRIVE CONTROL ECU (CANH, CANL)

9.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
a.
C317106C14
0.094,0.906 0.521,1.208 0.427,0.302 1.448,2.542 1.875,2.844 0.427,0.302 2.594,4.313 2.458,4.313 2.458,4.313 1.604,3.396 true 2.677,0.271 2.51,0.271 2.51,0.271 2.052,1.156 true 2.177,1.135 2.5,0.563 2.5,0.563 2.625,0.563 true 0.188,0.969 0.646,1.167 0.458,0.198 10 false G45 1.573,2.594 2.031,2.792 0.458,0.198 10 false G8 2.719,0.208 3.333,0.406 0.615,0.198 10 false CANH 2.729,0.479 3.344,0.677 0.615,0.198 10 false CANL 2.677,4.229 3.292,4.427 0.615,0.198 10 false CG 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.156,2.469 0.469,2.625 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-13 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G45-14 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

11.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
a.
C317106C15
0.083,1.313 0.51,1.615 0.427,0.302 1.448,2.542 1.875,2.844 0.427,0.302 2.594,4.313 2.458,4.313 2.458,4.313 1.594,3.375 true 1.458,1.979 1.604,1.979 1.604,1.979 1.885,1.396 true 1.552,2.25 1.698,2.25 1.698,2.25 2.021,1.375 true 0.198,1.385 0.656,1.583 0.458,0.198 10 false G83 1.573,2.594 2.031,2.792 0.458,0.198 10 false G8 1.094,2.177 1.542,2.375 0.448,0.198 10 false CANH 1.052,1.906 1.448,2.094 0.396,0.188 10 false CANL 2.677,4.229 3.292,4.427 0.615,0.198 10 false CG 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.156,2.469 0.469,2.625 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-24 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G83-23 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)
a.
C317106C16
1.49,0.063 1.917,0.365 0.427,0.302 1.448,2.542 1.875,2.844 0.427,0.302 0.688,2.031 0.833,2.031 0.833,2.031 1.073,1.563 true 0.677,1 0.802,1 0.802,1 1.052,1.292 true 0.896,2.74 1.042,2.74 1.042,2.74 1.604,3.24 true 1.604,0.135 2.063,0.333 0.458,0.198 10 false G85 1.583,2.604 2.042,2.802 0.458,0.198 10 false G8 0.229,0.927 0.667,1.125 0.438,0.198 10 false CANH 0.25,1.948 0.677,2.135 0.427,0.188 10 false CANL 0.604,2.677 0.885,2.875 0.281,0.198 10 false CG 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.156,2.469 0.469,2.625 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-17 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G85-28 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.
C317107C06
1.448,2.531 1.917,2.833 0.469,0.302 1.51,0.177 1.979,0.479 0.469,0.302 1.948,1.125 0.938,0.594 0.938,0.594 0.771,0.594 true 2.063,1.135 2.521,0.646 2.521,0.646 2.656,0.646 true 1.573,3.24 1.125,2.771 1.125,2.771 0.958,2.771 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.146,2.479 0.458,2.635 0.313,0.156 10 false *b 1.615,0.24 2.073,0.438 0.458,0.198 10 false G37 1.615,2.594 2.073,2.792 0.458,0.198 10 false G8 0.344,0.531 0.958,0.729 0.615,0.198 10 false CANH 2.729,0.552 3.344,0.75 0.615,0.198 10 false CANL 0.667,2.708 1.042,2.969 0.375,0.26 10 false CG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-9 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G37-10 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.
C317107C08
1.448,2.531 1.917,2.833 0.469,0.302 1.51,0.177 1.979,0.479 0.469,0.302 1.948,1.125 0.938,0.594 0.938,0.594 0.771,0.594 true 2.063,1.135 2.521,0.646 2.521,0.646 2.656,0.646 true 1.573,3.24 1.063,2.75 1.063,2.75 0.896,2.75 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.146,2.479 0.458,2.635 0.313,0.156 10 false *b 1.573,0.24 2.031,0.438 0.458,0.198 10 false G113 1.615,2.583 2.073,2.781 0.458,0.198 10 false G8 0.344,0.531 0.958,0.729 0.615,0.198 10 false CANH 2.729,0.552 3.344,0.75 0.615,0.198 10 false CANL 0.615,2.688 0.917,2.875 0.302,0.188 10 false CG
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of DLC3


Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-9 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G113-10 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C317114C04
1.448,2.521 1.927,2.781 0.479,0.26 1.521,0.125 2,0.385 0.479,0.26 1.74,1.083 2.49,0.531 2.49,0.531 2.635,0.531 true 1.646,1.073 0.885,0.552 0.885,0.552 0.719,0.552 true 1.583,3.25 1.021,2.781 1.021,2.781 0.854,2.781 true 0.104,0.063 0.417,0.219 0.313,0.156 10 false *a 0.104,2.438 0.417,2.594 0.313,0.156 10 false *b 1.646,0.177 2.104,0.375 0.458,0.198 10 false G33 1.604,2.573 2.063,2.771 0.458,0.198 10 false G8 2.719,0.438 3.177,0.635 0.458,0.198 10 false TX+ 0.438,0.458 0.896,0.656 0.458,0.198 10 false TX- 0.583,2.708 0.875,2.938 0.292,0.229 10 false CG
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-11 (TX+) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G33-12 (TX-) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

21.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C300856C12
1.542,2.781 1.958,3.052 0.417,0.271 1.396,0.208 1.813,0.479 0.417,0.271 1.865,1.927 1.979,1.927 1.979,1.927 2.521,1.063 true 2.667,1.063 2.719,1.948 2.719,1.948 2.833,1.948 true 0.719,4.396 0.844,4.396 0.844,4.396 1.635,3.563 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *a 0.198,2.635 0.51,2.792 0.313,0.156 10 false *b 1.656,2.844 1.938,3.01 0.281,0.167 10 false G8 1.479,0.26 1.844,0.417 0.365,0.156 10 false G77 1.583,1.844 2.01,2 0.427,0.156 10 false TX+ 2.896,1.875 3.323,2.031 0.427,0.156 10 false TX- 0.458,4.323 0.729,4.49 0.271,0.167 10 false CG
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-8 (TX+) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G77-9 (TX-) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

23.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
24.CHECK SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C300844C63
0.229,0.771 0.635,1.031 0.406,0.26 5.49,0.135 5.896,0.396 0.406,0.26 1.208,0.844 0.969,0.594 0.969,0.594 0.813,0.594 true 1.208,1.042 1.021,1.208 1.021,1.208 0.865,1.208 true 1.385,0.844 1.115,0.458 1.115,0.458 0.958,0.458 true 1.594,0.844 1.302,0.271 1.302,0.271 1.146,0.271 true 1.396,1.031 1.135,1.417 1.135,1.417 0.979,1.417 true 1.594,1.01 1.271,1.552 1.271,1.552 1.115,1.552 true 2.396,0.844 2.875,0.104 2.875,0.104 2.99,0.104 true 2.396,1.021 2.927,1.698 2.927,1.698 3.042,1.698 true 5.583,0.802 5.198,1.5 5.198,1.5 5.042,1.5 true 1.979,0.844 1.438,0.115 1.438,0.115 1.281,0.115 true 1.99,1.031 1.438,1.698 1.438,1.698 1.281,1.698 true 2.74,0.833 3.188,0.469 3.188,0.469 3.302,0.469 true 2.74,1.031 3.188,1.313 3.188,1.313 3.313,1.313 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 4.49,0.146 4.802,0.344 0.313,0.198 10 false *b 0.281,0.542 0.844,0.698 0.563,0.156 10 false CANH*c 0.333,1.135 0.896,1.292 0.563,0.156 10 false CANL*c 0.417,0.375 0.979,0.531 0.563,0.156 10 false CANH*d 0.594,0.198 1.156,0.354 0.563,0.156 10 false CANH*e 0.427,1.302 0.99,1.458 0.563,0.156 10 false CANL*d 0.583,1.469 1.146,1.625 0.563,0.156 10 false CANL*e 3.354,0.396 3.917,0.552 0.563,0.156 10 false CANH*h 3.104,1.594 3.677,1.781 0.573,0.188 10 false CANL*g 0.74,0.021 1.302,0.177 0.563,0.156 10 false CANH*f 3.365,1.229 3.927,1.385 0.563,0.156 10 false CANL*h 0.302,0.833 0.594,1.021 0.292,0.188 10 false G67 5.615,0.188 5.875,0.396 0.26,0.208 10 false G8 4.771,1.417 5.115,1.573 0.344,0.156 10 false CG 0.771,1.625 1.333,1.781 0.563,0.156 10 false CANL*f 3.042,0.021 3.604,0.219 0.563,0.198 10 false CANH*g
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3
*c to Brake Actuator Assembly (Skid Control ECU) *d to Airbag Sensor Assembly(w/ Airbag System)
*e to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC) *f to Combination Meter Assembly
*g to No. 2 CAN Junction Connector *h to Headlight Leveling ECU Assembly (for LED Headlight or w/ Headlight Cleaner System)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ VSC

*2: for LED Headlight or w/ Headlight Cleaner System

*3: w/ Airbag System

G67-1 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake Actuator Assembly (Skid Control ECU)
G67-11 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G67-2 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag Sensor Assembly*3
G67-12 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G67-3 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*1
G67-13 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G67-5 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination Meter Assembly
G67-15 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G67-6 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN Junction Connector
G67-16 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G67-8 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight Leveling ECU Assembly*2
G67-18 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid Control ECU] CAN branch wire) B
NG (to airbag sensor assembly CAN branch wire) (w/ Airbag System) C
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) (w/ VSC) D
NG (to combination meter assembly CAN main wire) E
NG (to headlight leveling ECU assembly CAN branch wire) (for LED Headlight or w/ Headlight Cleaner System) F
NG (to No. 2 CAN junction connector CAN main wire) G



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

25.CONNECT CONNECTOR

C

27.CONNECT CONNECTOR

D

29.CONNECT CONNECTOR

E

31.CONNECT CONNECTOR

F

33.CONNECT CONNECTOR

G

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

25.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
a.

Disconnect the brake actuator assembly (skid control ECU) connector.

C317108C06
1.083,0.292 1.521,0.573 0.438,0.281 3.448,0.26 3.885,0.542 0.438,0.281 5.823,0.281 6.26,0.563 0.438,0.281 2.917,2.26 3.115,2.26 3.115,2.26 3.375,1.5 true 5.625,1.906 5.771,1.906 5.771,1.906 5.969,1.271 true 3.375,1.406 3.01,0.646 3.01,0.646 2.865,0.646 true 1.635,1.208 0.927,0.656 0.927,0.656 0.76,0.656 true 0.917,2.167 1.073,2.167 1.073,2.167 1.615,1.344 true 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 4.938,0.104 5.25,0.26 0.313,0.156 10 false *b 1.229,0.344 1.542,0.542 0.313,0.198 10 false A4 3.583,0.323 3.896,0.521 0.313,0.198 10 false A3 5.948,0.344 6.26,0.542 0.313,0.198 10 false G8 0.333,2.094 0.948,2.292 0.615,0.198 10 false CANH*A 0.198,0.583 0.813,0.781 0.615,0.198 10 false CANL*A 2.323,2.177 2.938,2.375 0.615,0.198 10 false CANH*B 2.292,0.563 2.906,0.76 0.615,0.198 10 false CANL*B 1.625,0.365 1.938,0.563 0.313,0.198 10 false *A 3.99,0.333 4.302,0.531 0.313,0.198 10 false *B 5.354,1.813 5.896,2.031 0.542,0.219 10 false CG
*A w/ VSC *B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
A4-22 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A4-10 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

w/o VSC
Tester Connection Condition Specified Condition
A3-25 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A3-14 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.
C317109C08
1.479,2.573 1.958,2.865 0.479,0.292 1.531,0.125 2.01,0.417 0.479,0.292 2.083,1.094 2.469,0.615 2.469,0.615 2.625,0.615 true 2.188,1.344 2.5,1.906 2.5,1.906 2.646,1.906 true 0.854,2.823 0.99,2.823 0.99,2.823 1.573,3.219 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.156,2.542 0.469,2.698 0.313,0.156 10 false *b 1.656,0.188 2.115,0.385 0.458,0.198 10 false G42 1.646,2.625 2.104,2.823 0.458,0.198 10 false G8 2.688,0.531 3.302,0.729 0.615,0.198 10 false CANH 2.729,1.813 3.208,2.083 0.479,0.271 10 false CANL 0.583,2.75 0.896,2.958 0.313,0.208 10 false CG
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G42-13 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G42-22 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

29.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
a.
C317110C04
1.49,2.521 1.958,2.792 0.469,0.271 1.542,0.167 2.01,0.438 0.469,0.271 1.813,1.344 1.958,1.906 1.958,1.906 2.094,1.906 true 1.635,1.354 1.469,1.854 1.469,1.854 1.323,1.854 true 1.583,3.25 1,2.76 1,2.76 0.854,2.76 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.146,2.458 0.458,2.615 0.313,0.156 10 false *b 1.646,0.219 2.104,0.417 0.458,0.198 10 false G21 1.635,2.573 2.094,2.771 0.458,0.198 10 false G8 2.167,1.813 2.781,2.01 0.615,0.198 10 false CANH 0.906,1.802 1.323,2.042 0.417,0.24 10 false CANL 0.594,2.688 0.854,2.938 0.26,0.25 10 false CG
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])
*b Front view of DLC3


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G21-3 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G21-2 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (CANH, CANL)

31.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
a.
C317111C04
1.479,2.583 1.938,2.875 0.458,0.292 1.458,0.052 1.917,0.344 0.458,0.292 1.385,1.073 1.219,1.948 1.219,1.948 1.083,1.948 true 1.313,1.073 1.073,1.615 1.073,1.615 0.938,1.615 true 1.583,3.25 0.99,2.813 0.99,2.813 0.854,2.813 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.146,2.521 0.458,2.677 0.313,0.156 10 false *b 1.604,0.125 1.917,0.323 0.313,0.198 10 false G9 1.635,2.646 1.948,2.844 0.313,0.198 10 false G8 0.51,1.542 1.125,1.74 0.615,0.198 10 false CANH 0.667,1.875 1.281,2.073 0.615,0.198 10 false CANL 0.594,2.74 0.885,2.938 0.292,0.198 10 false CG
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-36 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G9-35 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

33.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
a.
C317113C04
1.417,2.51 1.906,2.781 0.49,0.271 1.49,0.125 1.979,0.396 0.49,0.271 2.24,0.938 1.146,0.417 1.146,0.417 0.969,0.417 true 2.417,0.948 2.563,0.385 2.563,0.385 2.688,0.385 true 1.563,3.229 1.073,2.833 1.073,2.833 0.896,2.833 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.146,2.49 0.458,2.646 0.313,0.156 10 false *b 1.594,0.177 2.052,0.375 0.458,0.198 10 false G80 1.583,2.573 2.042,2.771 0.458,0.198 10 false G8 0.542,0.344 1.156,0.542 0.615,0.198 10 false CANH 2.74,0.302 3.354,0.5 0.615,0.198 10 false CANL 0.615,2.76 0.927,3 0.313,0.24 10 false CG
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


Disconnect the headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-6 (CANH) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G80-7 (CANL) - G8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT LEVELING ECU ASSEMBLY (CANH, CANL)