Home › Engine / Hybrid System › 1GD-FTV EMISSION CONTROL › MONOLITHIC CONVERTER(w/ DPF)
RM3250E _51 Engine / Hybrid System _037974 1GD-FTV EMISSION CONTROL _0191230 MONOLITHIC CONVERTER(w/ DPF) A

1GD-FTV EMISSION CONTROL  MONOLITHIC CONVERTER(w/ DPF)  INSTALLATION  


PROCEDURE

Hide 25051 1.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.

Set a new gasket and the exhaust manifold converter sub-assembly to the turbocharger sub-assembly.


b.

Temporarily install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the 3 bolts.


c.
A344468C01
2.427,0.646 2.25,0.406 2.25,0.406 2.167,0.406 true 2.688,1.354 2.688,1.656 true 1.99,0.313 2.177,0.469 0.188,0.156 10 false *1 2.281,1.229 2.469,1.396 0.188,0.167 10 false *2 2.917,1.229 3.104,1.406 0.188,0.177 10 false *3 2.635,1.677 2.833,1.844 0.198,0.167 10 false *4 0.646,1.917 0.958,2.073 0.313,0.156 10 true 90°
*1 Exhaust Pipe Clamp
*2 Exhaust Manifold Converter
*3 Turbocharger Sub-assembly
*4 Gasket


Install a new exhaust pipe clamp to the exhaust manifold converter sub-assembly with a new nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.

Tighten the 3 bolts and install the exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17118 2.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY

a.

Install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the bolt and 2 new nuts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17271 3.INSTALL NO. 1 TURBO INSULATOR

a.

Install the No. 1 turbo insulator to the exhaust manifold and turbocharger sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 48691 6.INSTALL UPPER ARM BUSH HEAT INSULATOR

a.

Install the upper arm bush heat insulator to the body with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 45203 7.INSTALL NO. 2 INTERMEDIATE SHAFT SUB-ASSEMBLY (for RHD)

Hide 12631A 8.INSTALL ENGINE COVER BRACKET

a.

Install the engine cover bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 clamps and connect the engine wire to the cylinder head sub-assembly.


Hide 17578B 9.INSTALL PIPE CLAMP

a.

Install the pipe clamp to the engine cover bracket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25734 10.TEMPORARILY INSTALL NO. 2 VACUUM PIPE

a.

Install a new clamp to the pipe clamp.


b.

Temporarily install the No. 2 vacuum pipe to the exhaust manifold converter sub-assembly.


Hide 25733A 11.TEMPORARILY INSTALL NO. 1 VACUUM PIPE

a.

Temporarily install the No. 1 vacuum pipe to the exhaust manifold converter sub-assembly.


b.

Install a new clamp to the No. 1 vacuum pipe and No. 2 vacuum pipe with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 25734 12.TIGHTEN NO. 2 VACUUM PIPE

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the No. 2 vacuum pipe.

Torque:
Specified tightening torque : 48 N*m (489 kgf*cm, 35 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 42.9 N*m (437 kgf*cm, 32 ft.*lbf)




Hide 25733A 13.TIGHTEN NO. 1 VACUUM PIPE

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 17 mm union nut wrench, tighten the No. 1 vacuum pipe.

Torque:
Specified tightening torque : 48 N*m (489 kgf*cm, 35 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 42.9 N*m (437 kgf*cm, 32 ft.*lbf)




Hide 17801 17.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 53882F 19.INSTALL FRONT FENDER SEAL

a.

for 2WD:

Install the front fender seal to the body with 5 new clips.


b.

for 4WD and Pre-Runner:

Install the front fender seal to the body with 6 new clips.


Hide 17410 21.INSTALL FRONT EXHAUST PIPE ASSEMBLY