1.INSTALL STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
Using an E10 "TORX" socket wrench, install the 3 stud bolts at the positions shown in the illustration.
Using an E8 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.
Using an E5 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.
17275
2.INSTALL COMPRESSOR OUTLET ELBOW
except Cold Specification Vehicles:
Install the hose clamp with the bolt.
Install a new gasket.
Install a new gasket and the compressor outlet elbow with the 2 nuts.
17274
3.INSTALL COMPRESSOR INLET ELBOW
Using an E8 "TORX" socket wrench, install a new gasket and the compressor inlet elbow with the stud bolt.
Install the compressor inlet elbow to the turbocharger sub-assembly with the 2 nuts.
Install the compressor inlet elbow stay with the 2 bolts.
16027
4.INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
Install a new gasket.
Temporarily install the turbo water pipe sub-assembly with the bolt and 2 nuts.
Tighten the bolt and 2 nuts.
Connect the No. 1 turbo water hose and No. 2 turbo water hose to the No. 1 turbo water pipe sub-assembly and slide the 2 hose clips to secure the hoses.
15407
5.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY
| *a | NG |
| *b | OK |
Install a new gasket as shown in the illustration.
Do not install the gasket upside down.
Temporarily install the turbo oil inlet pipe sub-assembly with the 2 nuts.
17141
6.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
Install 2 new gaskets to the exhaust manifold and turbocharger sub-assembly.
Temporarily install the exhaust manifold to turbocharger sub-assembly with 3 new nuts.
| *A | w/ DPF |
| *B | w/o DPF |
| *1 | Collar |
|
Engine Side |
Temporarily install the exhaust manifold with turbocharger sub-assembly, 8 collars and the 8 plate washers to the cylinder head sub-assembly with 8 new nuts.
Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.
Install a new gasket on the union bolt side to turbo oil inlet pipe sub-assembly.
Temporarily install the union bolt.
15474
7.INSTALL TURBO OIL OUTLET PIPE
Install a new gasket to the turbo oil outlet pipe.
The claws of the gasket must face the turbo oil outlet pipe.
Install the turbo oil outlet pipe with the 2 bolts.
Connect the turbo oil outlet hose to the turbo oil outlet pipe, turbo oil inlet pipe and slide the 2 hose clips to secure the hoses.
17293
8.TEMPORARILY INSTALL TURBOCHARGER STAY
Temporarily install the turbocharger stay to the turbocharger sub-assembly, with 3 bolts and nut.
17141
9.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
| *A | w/ DPF |
| *B | w/o DPF |
Tighten the exhaust manifold with turbocharger sub-assembly, to the cylinder head sub-assembly with 8 nuts.
Tighten the nuts in the order shown in the illustration.
Tighten the turbocharger sub-assembly, to the exhaust manifold with the 3 nuts.
Tighten the 2 nuts and then union bolt of the turbo oil inlet pipe sub-assembly.
If the connecting part of the union bolt gasket is cracked, remove the connecting part.
17293
10.TIGHTEN TURBOCHARGER STAY
Tighten the 3 bolts and nut of the turbocharger stay in the order shown in the illustration.
87101
11.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
Temporarily install the No. 1 viscous heater bracket sub-assembly with 4 bolts.
Tighten the 4 bolts and of the No. 1 viscous heater bracket sub-assembly in the order shown in the illustration.
12.INSTALL WIRE HARNESS CLAMP BRACKET (for Manual Transmission)
w/o DPF:
Connect the wire harness with the bolt.
w/ DPF:
Connect the wire harness clamp and install the bolt.
w/ DPF:
for Automatic Transmission:
Connect the oil cooler tube bracket with the bolt.
13.INSTALL OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)
w/o DPF:
Connect the wire harness with the bolt.
w/ DPF:
Attach the 2 wire harness clamps and connect the wire harness.
for Automatic Transmission:
Connect the oil cooler tube bracket with the bolt.
25601
14.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
16284
15.CONNECT TURBO WATER HOSE
Connect the No. 1 turbo water hose and No. 2 turbo water hose to the water outlet sub-assembly, engine water pump assembly and slide the 2 hose clips to secure the hoses.
The turbocharger sub-assembly may be damaged if the No. 1 turbo water hose and No. 2 turbo water hose are connected to the wrong locations.
16268
16.INSTALL NO. 1 WATER BY-PASS PIPE
12261
17.INSTALL PCV HOSE (except Cold Area Specification Vehicles)
Attach the clamp and install the PCV hose.
Slide the 2 hose clips to secure the hoses.
12229
18.INSTALL PCV PIPE (for Cold Area Specification Vehicles)
Connect the PCV pipe to the compressor inlet elbow, cylinder head cover sub-assembly and slide the 2 hose clips to secure the hoses.
Install the PCV pipe with the bolt to the compressor outlet elbow.
Connect the No. 19 water by-pass hose to the compressor inlet elbow and slide the hose clip to secure the hoses.
Install the No. 20 water by-pass hose to the PCV pipe and No. 1 water by-pass pipe, and slide the 2 hose clips to secure the hoses.
16279
19.INSTALL NO. 3 WATER BY-PASS PIPE
Connect the 2 water hoses to the oil cooler assembly and No. 2 water by-pass pipe, and slide the 2 hose clips to secure the hoses.
Install the No. 3 water by-pass pipe with the bolt.
for Cold Specification Vehicles:
Install the water hose to the compressor inlet elbow and No. 3 water by-pass pipe, and slide the 2 hose clips to secure the hoses.
87120G
20.INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)
21.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)
17701
22.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Connect the 3 wire harness clamps.
17801
23.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner case.
17705
24.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
Attach the 4 clips to install the air cleaner cap sub-assembly with air cleaner hose.
Tighten the hose clamp.
Connect the mass air flow meter connector and attach the 2 wire harness clamps.
16711
25.INSTALL FAN SHROUD
16470
26.INSTALL RADIATOR RESERVOIR
44369A
27.INSTALL NO. 1 OIL RESERVOIR BRACKET
44360
28.CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY
16571C
29.INSTALL NO. 1 RADIATOR HOSE
17362B
30.INSTALL NO. 2 AIR TUBE
17344E
31.INSTALL NO. 4 AIR HOSE
17341F
32.INSTALL NO. 1 AIR HOSE
25051
33.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
34.ADD ENGINE OIL
35.ADD ENGINE COOLANT
36.INSPECT FOR COOLANT LEAK
37.INSPECT FOR OIL LEAK
38.INSPECT ENGINE OIL LEVEL
39.INSPECT FOR EXHAUST GAS LEAK
51410
40.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
41.PERFORM INITIALIZATION