Home › Drivetrain › R151F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › from 2016.01
RM3250E _52 Drivetrain _038034 R151F MANUAL TRANSMISSION / TRANSAXLE _0185606 MANUAL TRANSMISSION ASSEMBLY A

R151F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The manual transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


PROCEDURE

Hide 36100 1.INSTALL TRANSFER ASSEMBLY

Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C332413

Install the wire harness clamp bracket to the manual transmission unit assembly with the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 33019C 3.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C349864C02
0,0 0.313,0.156 0.313,0.156 10 false *A 0.042,2.313 0.354,2.469 0.313,0.156 10 false *B
*A for 2TR-FE
*B for 5L-E


Connect the 3 clamps and install the transmission breather sub-assembly.


Hide 33030 4.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

CAUTION:

The manual transmission unit assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.


a.

Make sure that the knock pins are not loose, bent, damaged or scratched.


b.

Operate the transmission jack and install the manual transmission unit assembly to the vehicle.

CAUTION:

Do not raise the manual transmission unit assembly more than necessary. If the manual transmission unit assembly is raised excessively, the vehicle may also be lifted up.


NOTICE:

Make sure that the manual transmission unit assembly is clear of all wiring and hoses.



c.

Align the input shaft with the clutch disc and install the manual transmission unit assembly to the engine.


d.
C349893C03
2.594,2.958 2.5,2.75 2.5,2.75 2.417,2.75 false 2.542,0.771 2.5,0.583 2.5,0.583 2.417,0.583 false 0.052,0.031 0.365,0.188 0.313,0.156 10 false *A 0.063,2.479 0.375,2.635 0.313,0.156 10 false *B 2.25,0.5 2.469,0.698 0.219,0.198 10 false *1 2.25,2.667 2.469,2.865 0.219,0.198 10 false *1 1.792,0.073 2.104,0.229 0.313,0.156 10 false a 0.083,1.271 0.333,1.5 0.25,0.229 10 false a 0.635,0.063 0.885,0.292 0.25,0.229 10 false a 2.198,1.875 2.448,2.104 0.25,0.229 10 false b 1.844,2.156 2.094,2.385 0.25,0.229 10 false b 0.083,1.698 0.333,1.927 0.25,0.229 10 false b 0.365,2.146 0.615,2.375 0.25,0.229 10 false b
*A for 2TR-FE
*B for 5L-E
*1 Transmission Breather Bracket


for 2TR-FE:

Install the transmission breather bracket and 7 bolts.

Torque:
for bolt a : 71.5 N*m (729 kgf*cm, 53 ft.*lbf)
for bolt b : 37.2 N*m (379 kgf*cm, 27 ft.*lbf)


e.

for 5L-E:

Install the transmission breather bracket and 4 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 5.CONNECT WIRE HARNESS

a.
C349863C02
0,0 0.313,0.156 0.313,0.156 10 false *A 0.042,2.365 0.354,2.521 0.313,0.156 10 false *B
*A for 2TR-FE
*B for 5L-E


for 2TR-FE:

Connect the 6 clamps and 2 connector.


b.

for 5L-E:

Connect the 4 clamps and 2 connectors.


Hide 12371A 6.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 51204 7.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
57 N*m (581 kgf*cm, 42 ft.*lbf)


b.

Connect the No. 3 frame crossmember sub-assembly to the rear engine mounting insulator.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 28100 8.INSTALL STARTER ASSEMBLY (for 5L-E)

Hide 28100 9.INSTALL STARTER ASSEMBLY (for 2TR-FE)

Hide 31470 10.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 11.CONNECT GROUND CABLE

a.
C332408

Connect the ground cable with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 33118 12.INSTALL STIFFENER PLATE (for 5L-E)

a.
C350617C03
1,3.917 1.167,3.917 1.167,3.917 1.417,3.469 false 1.844,1.5 2.167,1.75 2.167,1.75 2.333,1.75 false 2.354,1.667 2.667,1.823 0.313,0.156 10 false *1 0.833,3.833 1.146,3.99 0.313,0.156 10 false *2 1.948,0.135 2.104,0.333 0.156,0.198 10 false A 2.26,0.135 2.417,0.333 0.156,0.198 10 false A 1.115,2.385 1.271,2.583 0.156,0.198 10 false A 0.75,2.385 0.906,2.583 0.156,0.198 10 false A 0.813,1.781 0.969,1.979 0.156,0.198 10 false B 2.656,3.417 2.813,3.615 0.156,0.198 10 false B 2.583,4.021 2.74,4.219 0.156,0.198 10 false B
*1 Stiffener Plate RH
*2 Stiffener Plate LH


Install the stiffener plate RH with the 3 bolts.

Torque:
for bolt A : 37.3 N*m (380 kgf*cm, 28 ft.*lbf)
for bolt B : 68.7 N*m (701 kgf*cm, 51 ft.*lbf)


b.

Install the stiffener plate LH with the 4 bolts.

Torque:
for bolt A : 37.3 N*m (380 kgf*cm, 28 ft.*lbf)
for bolt B : 68.7 N*m (701 kgf*cm, 51 ft.*lbf)


Hide 17118 13.INSTALL MANIFOLD STAY (for 2TR-FE)

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 51407A 17.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51442 18.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51410 19.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 33530F 21.INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY

a.
C333520C01
1.813,1.719 1.948,1.896 0.135,0.177 10 false -
V100135

MP grease


Apply MP grease to the tip of the shift lever.


b.
C329000C01
1.146,0.24 1.354,0.458 0.208,0.219 10 false *a 1.75,2.906 1.938,3.083 0.188,0.177 10 false *b 1.844,4.271 2.021,4.448 0.177,0.177 10 false *c
*a Press down
*b Clockwise
*c Lock


Cover the shift lever cap with a cloth.


c.

While pressing down on the shift lever cap, turn it clockwise to install the shift lever.


d.

Attach the shift lever cap boot.


Hide 58280A 22.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot assembly with the 6 screws and 4 clips.


Hide 58810J 23.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58811A 24.INSTALL FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION