The urea injector opens the needle valve and injects urea solution according to operation signals sent by the urea pump control ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2048 | Reductant Injector Circuit Low (Bank 1 Unit 1) | When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more (1 trip detection logic). | ·
Open or short in urea injector set circuit ·
Urea injector set ·
Urea pump control ECU |
Comes on | DTC stored |
| P2049 | Reductant Injector Circuit High (Bank 1 Unit 1) | When the urea injector is operating, an open or short circuit occurs in the urea injector circuit for 5 seconds or more (1 trip detection logic). | ·
Open or short in urea injector set circuit ·
Urea injector set ·
Urea pump control ECU |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2048
P2049 |
Reductant Injection Valve (Active Test) |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the urea injector set.
Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>UREA INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Urea Injector Set) |
*b | Front view of wire harness connector
(to Urea Pump Control ECU) |
Disconnect the urea injector set connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C138-2 - g1-8 (UIV+) | Always | Below 1 Ω |
| C138-1 - g1-7 (UIV-) | Always | Below 1 Ω |
| C138-2 or g1-8 (UIV+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C138-1 or g1-7 (UIV-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Reductant Injection Valve.
Perform the Active Test.
| Tester Display |
|---|
| Reductant Injection Valve |
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2048 or P2049 is output | A |
| No DTC is output | B |
A
B
Replace the urea pump control ECU.
Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Reductant Injection Valve.
Perform the Active Test.
| Tester Display |
|---|
| Reductant Injection Valve |
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the urea injector set.
Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>UREA INJECTOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT