Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P205C  Reductant Tank Temperature Sensor Circuit Low  P205D  Reductant Tank Temperature Sensor Circuit High  


DESCRIPTION

Refer to DTC P202B.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>P202B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P205C Reductant Tank Temperature Sensor Circuit Low An open or short circuit occurs in the temperature sensor circuit for 10 seconds or more (1 trip detection logic).
·

Open or short in temperature sensor circuit

·

Temperature sensor (urea pump)

·

Urea pump control ECU


Comes on DTC stored
P205D Reductant Tank Temperature Sensor Circuit High An open or short circuit occurs in the temperature sensor circuit for 10 seconds or more (1 trip detection logic).
·

Open or short in temperature sensor circuit

·

Temperature sensor (urea pump)

·

Urea pump control ECU


Comes on DTC stored

Related Data List
DTC No. Data List
P205C
P205D
Reductant Temperature

MONITOR DESCRIPTION

The urea pump control ECU calculates the temperature of the urea solution based on the output voltage of the temperature sensor. When the temperature sensor output voltage is outside the normal range, there may be a malfunction, short or open circuit in the temperature sensor. In this case, the urea pump control ECU determines that there is a malfunction in the temperature sensor, and then illuminates the MIL and stores a DTC through the ECM.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P205C
P205D
Ignition switch to ON and wait for 10 seconds or more.

WIRING DIAGRAM

A357974E03
1.604,1.458 2.063,1.656 0.458,0.198 10 false TUW 1.51,1.979 2.125,2.177 0.615,0.198 10 false ETUW 5.406,1.49 5.865,1.688 0.458,0.198 10 false THU 5.406,2.073 6.021,2.271 0.615,0.198 10 false ETHU 5.115,1.698 5.427,1.896 0.313,0.198 10 false 54 5.125,2.313 5.438,2.51 0.313,0.198 10 false 53 0.531,2.781 0.844,2.979 0.313,0.198 10 false g6 0.542,2.958 2.625,3.417 2.083,0.458 10 false Temperature Sensor (Urea Pump) 5.385,3.094 5.698,3.292 0.313,0.198 10 false g1 5.396,3.26 6.969,3.635 1.573,0.375 10 false Urea Pump Control ECU 2.01,1.698 2.167,1.896 0.156,0.198 10 false 1 2.021,2.323 2.177,2.521 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (REDUCTANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Temperature.


d.

Read the values.

Powertrain > Engine > Data List
Tester Display
Reductant Temperature
50003 234 1131
Standard:

Reductant temperature is the same as the ambient temperature of urea tank assembly.


Result:
Result Proceed to
-40°C (-40°F) A
80°C (176°F) B


HINT:
·

When the GTS indicates -40°C (-40°F), there is a open circuit.

·

When the GTS indicates 80°C (176°F), there is a short circuit.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the urea pump connector.

A360344C04
5.583,0.667 5.885,0.927 0.302,0.26 5.656,2.115 6,1.333 true 6.49,2.125 6.135,1.354 true 1.177,0.26 1.49,0.417 0.313,0.156 10 false *1 3.635,0.26 3.948,0.417 0.313,0.156 10 false *2 4.938,0.281 5.25,0.438 0.313,0.156 10 false *a 2.188,0.979 2.646,1.177 0.458,0.198 10 false TUW 2.104,1.802 2.719,2 0.615,0.198 10 false ETUW 5.458,2.167 6.073,2.365 0.615,0.198 10 false ETUW 6.448,2.188 6.906,2.385 0.458,0.198 10 false TUW 5.656,0.729 5.969,0.927 0.313,0.198 10 false g6
*1 Temperature Sensor (Urea Pump) *2 Urea Pump Control ECU
*a Front view of wire harness connector
(to Urea Pump)
- -



b.

Connect terminals 1 (TUW) and 2 (ETUW) of the urea pump connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Temperature.


f.

Read the values.

Powertrain > Engine > Data List
Tester Display
Reductant Temperature
50003 234 1131
OK:

80°C (176°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE UREA PUMP

NG

5.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR - UREA PUMP CONTROL ECU)
3.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON and wait for 10 seconds or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTCs are not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

5.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR - UREA PUMP CONTROL ECU)
A360342C15
1.594,0.125 2.021,0.354 0.427,0.229 5.302,0.115 5.729,0.344 0.427,0.229 1.813,1.448 2.073,0.792 true 2.208,0.802 2.573,1.417 true 4.99,1.479 5.438,1.156 true 5.521,1.146 5.823,1.49 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 4.229,0.156 4.542,0.313 0.313,0.156 10 false *b 1.74,0.167 2.052,0.365 0.313,0.198 10 false g6 5.427,0.156 5.74,0.354 0.313,0.198 10 false g1 1.563,1.479 2.021,1.677 0.458,0.198 10 false ETUW 2.542,1.469 3,1.667 0.458,0.198 10 false TUW 4.646,1.5 5.875,1.698 1.229,0.198 10 false 53 (ETHU) 5.656,1.51 6.729,1.708 1.073,0.198 10 false 54 (THU)
*a Front view of wire harness connector
(to Urea Pump)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Disconnect the urea pump connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g6-1 (TUW) - g1-54 (THU) Always Below 1 Ω
g6-2 (ETUW) - g1-53 (ETHU) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE UREA PUMP CONTROL ECU

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE UREA PUMP CONTROL ECU

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A357975C02
0.76,1.573 1.073,1.729 0.313,0.156 10 false *1 2.688,1.604 3,1.76 0.313,0.156 10 false *2
*1 Temperature Sensor (Urea Pump)
*2 Urea Pump Control ECU


Disconnect the urea pump connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Temperature.


f.

Read the values.

Powertrain > Engine > Data List
Tester Display
Reductant Temperature
50003 234 1131
OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE UREA PUMP

NG

9.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR - UREA PUMP CONTROL ECU)
9.CHECK HARNESS AND CONNECTOR (TEMPERATURE SENSOR - UREA PUMP CONTROL ECU)
A360342C16
1.594,0.125 2.021,0.354 0.427,0.229 5.302,0.115 5.729,0.344 0.427,0.229 2.208,0.792 2.573,1.417 true 5.521,1.156 5.823,1.49 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 4.229,0.156 4.542,0.313 0.313,0.156 10 false *b 1.729,0.167 2.042,0.365 0.313,0.198 10 false g6 5.427,0.156 5.74,0.354 0.313,0.198 10 false g1 2.458,1.458 2.917,1.656 0.458,0.198 10 false TUW 5.656,1.51 6.729,1.708 1.073,0.198 10 false 54 (THU)
*a Front view of wire harness connector
(to Urea Pump)
*b Front view of wire harness connector
(to Urea Pump Control ECU)


a.

Disconnect the urea pump connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g6-1 (TUW) and g1-54 (THU) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE UREA PUMP CONTROL ECU

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR