Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U029D  Lost Communication with NOx Sensor "A"  


DESCRIPTION

The ECM sends and receives data to and from the nitrogen oxides sensor assembly via local CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U029D Lost Communication with NOx Sensor "A" Communication stops between the ECM and the nitrogen oxides sensor assembly for 1.6 seconds or more (1 trip detection logic).
·

Nitrogen oxides sensor assembly

·

Harness or connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the nitrogen oxides sensor assembly and ECM.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U029D Ignition switch ON and wait for 1.6 seconds or more.

WIRING DIAGRAM

A383044E01
1.76,1.24 2.5,1.438 0.74,0.198 10 false NOX PM 0.802,0.615 1.542,0.813 0.74,0.198 10 false NOX PM 3.24,2.01 6.188,2.25 2.948,0.24 10 false Nitrogen Oxides Sensor Assembly 3.229,1.833 3.542,2.031 0.313,0.198 10 false e1 0.51,2.083 1.281,2.292 0.771,0.208 10 false DCU-MAIN 0.5,4.365 1.573,4.563 1.073,0.198 10 false FL MAIN 0.896,3.448 1.667,3.646 0.771,0.198 10 false J/B-B 2.479,3.458 3.688,3.656 1.208,0.198 10 false EFI-MAIN NO. 2 2.396,4.625 3.604,4.823 1.208,0.198 10 false EFI-MAIN NO. 1 3.427,5.156 4.635,5.354 1.208,0.198 10 false EFI-MAIN NO. 1 3.427,4.031 4.635,4.229 1.208,0.198 10 false EFI-MAIN NO. 2 4.365,3.438 5.188,3.604 0.823,0.167 10 false EFI NO. 1 5.104,3.292 5.417,3.49 0.313,0.198 10 false 2G 5.104,4.469 5.417,4.667 0.313,0.198 10 false 2G 5.115,3.698 5.427,3.896 0.313,0.198 10 false 2P 5.115,4.823 5.427,5.021 0.313,0.198 10 false 2P 1.865,3.292 2.177,3.49 0.313,0.198 10 false 2B 1.865,3.698 2.177,3.896 0.313,0.198 10 false 2J 1.854,4.833 2.167,5.031 0.313,0.198 10 false 2K 6.135,5.344 6.594,5.542 0.458,0.198 10 false G85 6.135,5.521 6.594,5.719 0.458,0.198 10 false ECM 5.146,3.135 5.302,3.333 0.156,0.198 10 false 3 5.156,3.542 5.313,3.74 0.156,0.198 10 false 9 5.156,4.302 5.313,4.5 0.156,0.198 10 false 7 5.156,4.667 5.313,4.865 0.156,0.198 10 false 8 1.896,4.667 2.052,4.865 0.156,0.198 10 false 3 1.896,3.542 2.052,3.74 0.156,0.198 10 false 5 1.896,3.135 2.052,3.333 0.156,0.198 10 false 1 2.896,4.344 3.052,4.542 0.156,0.198 10 false 2 2.635,4.344 2.792,4.542 0.156,0.198 10 false 1 2.781,3.188 2.938,3.385 0.156,0.198 10 false 1 3.042,3.188 3.198,3.385 0.156,0.198 10 false 2 4.76,3.177 4.917,3.375 0.156,0.198 10 false 2 4.5,3.177 4.656,3.375 0.156,0.198 10 false 1 0.885,3.188 1.042,3.385 0.156,0.198 10 false 1 1.146,3.188 1.302,3.385 0.156,0.198 10 false 2 0.25,2.24 0.406,2.438 0.156,0.198 10 false 1 0.26,1.938 0.417,2.135 0.156,0.198 10 false 2 0.875,0.354 1.031,0.552 0.156,0.198 10 false 1 1.146,0.354 1.302,0.552 0.156,0.198 10 false 2 0.604,5.688 1.198,5.865 0.594,0.177 10 false Battery 2.24,5.49 5.583,5.719 3.344,0.229 10 false Instrument Panel Junction Block Assembly 5.896,4.833 6.51,5.031 0.615,0.198 10 false MREL 3.458,0.469 4.073,0.667 0.615,0.198 10 false BATT 3.917,0.5 4.531,0.698 0.615,0.198 10 false CAN+ 3.938,1.021 4.552,1.219 0.615,0.198 10 false CAN- 3.969,1.438 4.427,1.635 0.458,0.198 10 false GND 5.896,0.521 6.51,0.719 0.615,0.198 10 false CANU 5.896,1.031 6.51,1.229 0.615,0.198 10 false CAND 5.646,4.917 5.958,5.115 0.313,0.198 10 false 14 3.271,0.573 3.427,0.771 0.156,0.198 10 false 5 4.375,1.177 4.531,1.375 0.156,0.198 10 false 3 4.365,0.667 4.521,0.865 0.156,0.198 10 false 2 4.375,1.51 4.531,1.708 0.156,0.198 10 false 4 5.625,0.677 5.938,0.875 0.313,0.198 10 false 27 5.635,1.188 5.948,1.385 0.313,0.198 10 false 35 2.375,0.573 2.531,0.771 0.156,0.198 10 false 3 1.552,0.573 1.708,0.771 0.156,0.198 10 false 5 1.563,1.052 1.719,1.25 0.156,0.198 10 false 2 2.365,1.052 2.521,1.25 0.156,0.198 10 false 1 1.833,6.323 4.125,6.531 2.292,0.208 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U029D is output A
DTC U029D and other DTCs are output* B


HINT:

*: If any other DTCs are output, perform troubleshooting for those DTCs first.




A

2.CHECK NITROGEN OXIDES SENSOR ASSEMBLY

B

2.CHECK NITROGEN OXIDES SENSOR ASSEMBLY
a.

Disconnect the nitrogen oxides sensor assembly connector.


b.

Turn the ignition switch to ON.


c.
A383897C01
1.469,0.198 1.948,0.531 0.479,0.333 1.656,1.833 1.76,1.833 1.76,1.833 1.885,1.271 true 2.5,1.833 2.333,1.833 2.333,1.833 2.198,1.271 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.646,0.292 1.958,0.49 0.313,0.198 10 false e1 1.333,1.76 1.792,1.958 0.458,0.198 10 false GND 2.552,1.76 3.094,1.958 0.542,0.198 10 false BATT
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor Assembly )


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-5 (BATT) - e1-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR ASSEMBLY - ECM)

NG

6.INSPECT NOX PM RELAY
3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR ASSEMBLY - ECM)
a.

Disconnect the nitrogen oxides sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-2 (CAN+) - G85-27 (CANU) Always Below 1 Ω
e1-3 (CAN-) - G85-35 (CAND) Always Below 1 Ω
e1-2 (CAN+) or G85-27 (CANU) - Body ground and other terminals Always 10 kΩ or higher
e1-3 (CAN-) or G85-35 (CAND) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE NITROGEN OXIDES SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.REPLACE NITROGEN OXIDES SENSOR ASSEMBLY
a.

Replace the nitrogen oxides sensor assembly.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and wait for 1.6 seconds or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
No DTC is output A
DTC U029D is output B



A

END

B

6.INSPECT NOX PM RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 6 INSTRUMENT PANEL RELAY BLOCK - NITROGEN OXIDES SENSOR ASSEMBLY, BATTERY)

NG

REPLACE NOX PM RELAY

7.CHECK HARNESS AND CONNECTOR (NO. 6 INSTRUMENT PANEL RELAY BLOCK - NITROGEN OXIDES SENSOR ASSEMBLY, BATTERY)
a.

Disconnect the nitrogen oxides sensor assembly connector.


b.

Remove the NOX PM relay from the No. 6 instrument panel relay block.


c.

Measure the resistance according to the value(s) in the table below.

A383898C01
1.531,0.594 1.969,0.906 0.438,0.313 2.156,1.594 2.427,2.115 2.427,2.115 2.563,2.115 true 1.875,1.615 1.667,2.135 1.667,2.135 1.552,2.135 true 0.646,0.417 0.958,0.615 0.313,0.198 10 false *a 3.927,0.115 4.24,0.313 0.313,0.198 10 false *1 3.938,1.188 4.25,1.385 0.313,0.198 10 false *b 2.625,2.031 3.313,2.24 0.688,0.208 10 false BATT 1.677,0.667 2.365,0.875 0.688,0.208 10 false e1 1.229,2.063 1.917,2.271 0.688,0.208 10 false GND
*1 No. 6 Instrument Panel Relay Block - -
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor Assembly)
*b Front view of wire harness connector
(to NOX PM Relay)


Standard Resistance:
Tester Connection Condition Specified Condition
e1-5 (BATT) - NOX PM relay terminal 3 Always Below 1 Ω
e1-4 (GND) - Body ground Always Below 1 Ω
NOX PM relay terminal 2 - Body ground Always Below 1 Ω
NOX PM relay terminal 3 or e1-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
NOX PM relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR