Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P0942  Hydraulic Pressure Unit  


DESCRIPTION

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P2796

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0942 Hydraulic Pressure Unit The following condition continues for 0.032 seconds or more (2 trip detection logic):
·

Difference between turbine speed and output shaft speed is 330 rpm or more within 0.2 seconds after engine restarted during idling stop when shift lever is in D.


·

Electromagnetic oil pump

·

Engine stop and start ECU


Blinks DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Depress the brake pedal and stop the vehicle.


g.

Keep the engine stopped by stop and start control. (Keep the shift lever in D.)


h.

Release the brake pedal with the shift lever in D to start the engine.


i.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Depress the brake pedal and stop the vehicle.


e.

Allow the engine to stop by stop and start control. (Keep the shift lever in D.)


f.

Release the brake pedal with the shift lever in D to start the engine.



CAUTION / NOTICE / HINT

NOTICE:

When the electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION


HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.CHECK ENGINE STOP AND START ECU (EMOP TERMINAL WAVEFORM)
a.

Drive the vehicle to warm up the engine and automatic transmission fluid.

HINT:

The electromagnetic oil pump may not operate properly if the automatic transmission fluid temperature is low. Make sure to warm up the automatic transmission fluid before performing the Active Test. (Automatic transmission fluid temperature: 25°C (77°F))



b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.

HINT:

Do not start the engine.



d.

Turn the GTS on.


e.

Connect an oscilloscope to terminals G127-9 (EMOP), G127-8 (EGND) and G125-8 (GND1).

A346331C91
4.635,0.615 5.156,0.844 0.521,0.229 2.01,0.594 2.531,0.823 0.521,0.229 4.719,1.427 4.531,2.156 true 4.792,1.448 5.385,2.104 true 1.865,1.417 1.365,2.115 true 4.302,2.198 4.865,2.406 0.563,0.208 10 false EMOP 5.24,2.177 5.854,2.375 0.615,0.198 10 false EGND 4.74,0.656 5.198,0.854 0.458,0.198 10 false G127 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.156,2.177 1.771,2.375 0.615,0.198 10 false GND1 2.115,0.635 2.573,0.833 0.458,0.198 10 false G125
*a Component with harness connected
(Engine Stop and Start ECU)
- -



f.

Enter the following menus: Powertrain / Stop and Start / Active Test / Electromagnetic Oil Pump.


g.
A345972E01
0.115,0.115 1.49,0.313 1.375,0.198 10 false 10 V/DIV. 1.281,1.896 2.052,2.094 0.771,0.198 10 false 20 ms./DIV. 0.115,1.396 0.573,1.594 0.458,0.198 10 false GND 0.219,1.135 0.531,1.333 0.313,0.198 10 false +B 0.104,0.875 0.719,1.073 0.615,0.198 10 false 43 V

Check the waveform while performing the Active Test.

Item Condition
Tester Connection G127-9 (EMOP) - G125-8 (GND1)
G127-8 (EGND) - G125-8 (GND1)
Tool Setting 10 V/DIV., 20 ms./DIV.
Condition
·

Ignition switch ON (engine is stopped)

·

Active Test "Electromagnetic Oil Pump" being performed



Standard:

The waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs
50002 227

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON.


b.

Start the engine.


c.

Perform a road test.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Result Proceed to
DTC P0942 is output A
DTC P0942 is not output B




A

B