Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P1780  Discrepancy between Neutral Position SW and Shift Position  


DESCRIPTION

for Automatic Transmission:

The engine stop and start ECU detects malfunctions by comparing the conditions of the shift position signal and NSW signal. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator light, prohibits stop and start control and stores DTC P1780.

for Manual Transmission:

The engine stop and start ECU detects a malfunction by comparing the shift position signal with the neutral position sensor (neutral position switch) signal input state. When a malfunction occurs, the engine stop and start ECU stores this DTC, blinks the stop and start cancel indicator light, and prohibits the stop and start control.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1780 Discrepancy between Neutral Position SW and Shift Position for Automatic Transmission:
Both of the following conditions are met for 2 seconds or more (2 trip detection logic) (*1):
·

Ignition switch ON

·

NSW signal is ON with the shift lever in D


Both of the following conditions are met for 2 seconds or more (2 trip detection logic) (*1):
·

Ignition switch ON

·

NSW signal is ON with the shift lever in R


Both of the following conditions are met for 15 seconds or more (2 trip detection logic) (*2):
·

Ignition switch ON

·

NSW signal is ON with the shift lever in P or N


for Manual Transmission:
The following condition continues for 1 second or more (1 trip detection logic):
·

Open or short in neutral position sensor (neutral position switch) circuit.


·

for Automatic Transmission:

Park/neutral position switch assembly

·

for Manual Transmission:

Neutral position sensor (neutral position switch)

·

Engine stop and start ECU

·

ECM

·

Wire harness or connector


Blinks DTC stored

*1: "ON" is displayed for the freeze frame data item [Neutral Switch Stuck ON]

*2: "ON" is displayed for the freeze frame data item [Neutral Switch Stuck OFF]

WIRING DIAGRAM

for Automatic Transmission:


A382137E01
4.417,1.854 5.781,2.25 1.365,0.396 10 false Park/Neutral Position Switch Assembly 4.417,1.677 4.792,1.844 0.375,0.167 10 false C24 5.948,4.177 6.323,4.344 0.375,0.167 10 false G126 5.969,4.344 7.063,4.698 1.094,0.354 10 false Engine Stop and Start ECU 5.958,1.115 6.333,1.281 0.375,0.167 10 false 17 5.969,3.656 6.344,3.823 0.375,0.167 10 false 21 6.198,3.563 6.573,3.729 0.375,0.167 10 false STA 6.198,0.979 6.656,1.167 0.458,0.188 10 false CLL* 0.438,4.917 0.906,5.188 0.469,0.271 10 false ECM 0.792,3.969 1.26,4.24 0.469,0.271 10 false D 0.792,3.521 1.26,3.792 0.469,0.271 10 false N 0.792,3.104 1.26,3.375 0.469,0.271 10 false R 0.792,2.677 1.26,2.948 0.469,0.271 10 false P 0.563,0.958 1.031,1.229 0.469,0.271 10 false NSW 1.031,2.677 1.5,2.948 0.469,0.271 10 false C57 1.021,0.969 1.49,1.24 0.469,0.271 10 false G85 1.031,3.104 1.5,3.375 0.469,0.271 10 false C57 1.021,3.531 1.49,3.802 0.469,0.271 10 false C57 1.042,3.979 1.51,4.25 0.469,0.271 10 false C57 3.396,0.583 4.885,0.823 1.49,0.24 10 false from IG1 NO. 1 Fuse 1.021,0.76 1.49,1.031 0.469,0.271 10 false 11 1.063,2.438 1.531,2.708 0.469,0.271 10 false 12 1.083,2.896 1.552,3.167 0.469,0.271 10 false 15 1.063,3.323 1.531,3.594 0.469,0.271 10 false 13 1.073,3.771 1.542,4.042 0.469,0.271 10 false 14 2.052,2.531 2.521,2.802 0.469,0.271 10 false 6 2.521,2.521 2.99,2.792 0.469,0.271 10 false 1 2.969,2.521 3.438,2.792 0.469,0.271 10 false 9 3.427,2.531 3.896,2.802 0.469,0.271 10 false 7 3.906,2.542 4.375,2.813 0.469,0.271 10 false 5 2.646,1.417 3.115,1.688 0.469,0.271 10 false RB 3.875,1.438 4.344,1.708 0.469,0.271 10 false B 2.792,1.177 3.26,1.448 0.469,0.271 10 false 2 3.875,1.177 4.344,1.448 0.469,0.271 10 false 4 3.875,2.271 4.344,2.542 0.469,0.271 10 false L 3.385,2.292 3.854,2.563 0.469,0.271 10 false DL 2.917,2.281 3.385,2.552 0.469,0.271 10 false NL 2.438,2.281 2.906,2.552 0.469,0.271 10 false RL 1.979,2.292 2.448,2.563 0.469,0.271 10 false PL 3.792,4.167 5.188,4.385 1.396,0.219 10 false to ST NO. 1 Relay


for Manual Transmission:


A348539E11
0.51,2.229 4.281,2.448 3.771,0.219 10 false Neutral Position Sensor (Neutral Position Switch) 0.51,2.042 0.969,2.24 0.458,0.198 10 false C105 1.51,0.469 1.969,0.667 0.458,0.198 10 false W1 1.427,1.042 1.885,1.24 0.458,0.198 10 false TMN 1.542,1.583 2,1.781 0.458,0.198 10 false F+ 5.656,0.469 6.313,0.667 0.656,0.198 10 false TMVC 5.667,1.021 6.125,1.219 0.458,0.198 10 false TMN 5.646,1.583 6.104,1.781 0.458,0.198 10 false TME2 1.833,0.573 2.292,0.771 0.458,0.198 10 false 1 1.833,1.156 2.292,1.354 0.458,0.198 10 false 2 1.823,1.698 2.281,1.896 0.458,0.198 10 false 3 5.406,0.583 5.667,0.792 0.26,0.208 10 false 26 5.469,1.146 5.958,1.333 0.49,0.188 10 false 8 5.396,1.698 5.677,1.896 0.281,0.198 10 false 25 5.76,2.229 6.823,2.573 1.063,0.344 10 false Engine Stop and Start ECU 5.76,2.052 6.219,2.25 0.458,0.198 10 false G126


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for Automatic Transmission:

When the engine stop and start ECU is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Automatic Transmission A
for Manual Transmission B



A

2.READ VALUE USING GTS

B

8.READ VALUE USING GTS (NEUTRAL SWITCH)
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
-
Shift SW Status (R Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in R
ON: Shift lever in R
-
Shift SW Status (N Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in N
ON: Shift lever in N
-
Shift SW Status (D Range) Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in D or S
ON: Shift lever in D or S
-
Powertrain > Engine and ECT > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 234 125,126,127,128

Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (NEUTRAL POSITION SW OR NEUTRAL POSITION SW SIGNAL)

NG

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.READ VALUE USING GTS (NEUTRAL POSITION SW OR NEUTRAL POSITION SW SIGNAL)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List.


b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch assembly status OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N
-
Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
50003 234 147

Result:
Proceed to
OK
NG



OK

NG

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Disconnect the C24 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-21 (STA) - C24-5 (L) Always Below 1 Ω
G126-17 (CLL) - C24-4 (B) Always Below 1 Ω
G126-21 (STA) - Body ground Always 80 to 180 Ω
G126-17 (CLL) - Body ground Always 10 kΩ or higher
C24-5 (L) - Body ground Always 80 to 180 Ω
C24-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G85 and C57 ECM connectors.


b.

Disconnect the C24 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C57-12 (P) - C24-6 (PL) Always Below 1 Ω
C57-15 (R) - C24-1 (RL) Always Below 1 Ω
C57-13 (N) - C24-9 (NL) Always Below 1 Ω
C57-14 (D) - C24-7 (DL) Always Below 1 Ω
G85-11 (NSW) - C24-4 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9

e.

Read the value when the shift lever is in neutral and any other position

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in neutral ON
Shift lever in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Disconnect the C105 neutral position sensor (neutral position switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-26 (TMVC) - C105-1 (W1) Always Below 1 Ω
G126-25 (TME2) - C105-3 (F+) Always Below 1 Ω
G126-8 (TMN) - C105-2 (TMN) Always Below 1 Ω
G126-26 (TMVC) - Body ground Always 10 kΩ or higher
C105-1 (W1) - Body ground Always 10 kΩ or higher
G126-25 (TME2) - Body ground Always 10 kΩ or higher
C105-3 (F+) - Body ground Always 10 kΩ or higher
G126-8 (TMN) - Body ground Always 10 kΩ or higher
C105-2 (TMN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
A346331C99
3.188,0.615 3.708,0.844 0.521,0.229 2.521,0.583 2.771,0.583 2.771,0.583 3.104,1.167 true 3.115,1.333 3.198,2.198 true 3.292,0.646 3.75,0.844 0.458,0.198 10 false G126 3.021,2.24 3.521,2.438 0.5,0.198 10 false TME2 2.083,0.5 2.5,0.75 0.417,0.25 10 false TMN 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G126-8 (TMN) - G126-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Proceed to
OK
NG



OK

NG