Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Neutral Position Switch Circuit  


DESCRIPTION

for Automatic Transmission:

The engine stop and start ECU uses the park/neutral position switch assembly installed to the automatic transmission assembly to detect when the shift lever is in P or N.

for Manual Transmission:

The neutral position sensor (neutral position switch) detects whether the shift lever is in neutral. When the shift lever in any position other than neutral, stop and start control is prohibited.

PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Automatic Transmission A
for Manual Transmission B



A

2.READ VALUE USING GTS (NEUTRAL SWITCH)

B

5.READ VALUE USING GTS (NEUTRAL SWITCH)
2.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9
OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever in P or N ON
Shift lever not in P or N OFF



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Disconnect the C24 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-21 (STA) - C24-5 (L) Always Below 1 Ω
G126-17 (CLL) - C24-4 (B) Always Below 1 Ω
G126-21 (STA) - Body ground Always 80 to 180 Ω
G126-17 (CLL) - Body ground Always 10 kΩ or higher
C24-5 (L) - Body ground Always 80 to 180 Ω
C24-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Neutral Switch.

Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9

e.

Read the value when the shift lever is in neutral and any other position

OK:
Tester Display Condition Normal Condition
Neutral Switch Shift lever is in neutral ON
Shift lever is in any position other than neutral OFF



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NEUTRAL POSITION SENSOR (NEUTRAL POSITION SWITCH))
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Disconnect the C105 neutral position sensor (neutral position switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-26 (TMVC) - C105-1 (W1) Always Below 1 Ω
G126-25 (TME2) - C105-3 (F+) Always Below 1 Ω
G126-8 (TMN) - C105-2 (TMN) Always Below 1 Ω
G126-26 (TMVC) - Body ground Always 10 kΩ or higher
C105-1 (W1) - Body ground Always 10 kΩ or higher
G126-25 (TME2) - Body ground Always 10 kΩ or higher
C105-3 (F+) - Body ground Always 10 kΩ or higher
G126-8 (TMN) - Body ground Always 10 kΩ or higher
C105-2 (TMN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ENGINE STOP AND START ECU (TMN TERMINAL VOLTAGE)
A346331C99
3.188,0.615 3.708,0.844 0.521,0.229 2.521,0.583 2.771,0.583 2.771,0.583 3.104,1.167 true 3.115,1.333 3.198,2.198 true 3.292,0.646 3.75,0.844 0.458,0.198 10 false G126 3.021,2.24 3.521,2.438 0.5,0.198 10 false TME2 2.083,0.5 2.5,0.75 0.417,0.25 10 false TMN 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G126-8 (TMN) - G126-25 (TME2) Ignition switch ON, shift lever in neutral 2.7 to 4.3 V
Ignition switch ON, shift lever in any position other than neutral 0.7 to 1.9 V



Result:
Proceed to
OK
NG



OK

GO TO PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG