Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _053992 STOP AND START _0262513 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P2531  Ignition Switch Run Position Circuit Low  


DESCRIPTION

When the engine stop and start ECU receives the OFF signal from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 when communication with the ECM is normal, the engine stop and start ECU stores DTC P2531.

*1: w/o Entry and Start System

*2: w/ Entry and Start System


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P2531 Ignition Switch Run Position Circuit Low Both of the following conditions continue for 10 seconds or more (1 trip detection logic):
·

Ignition switch off signal is input.

·

Communication with the ECM is normal.


·

Wire harness or connector

·

IG2 relay (w/ Entry and Start System)

·

Instrument panel junction block assembly (EFI-MAIN NO. 1, EFI-MAIN NO. 2 relay)

·

Ignition or starter switch assembly (w/o Entry and Start System)

·

Certification ECU (Smart key ECU assembly) (w/ Entry and Start System)

·

Engine stop and start ECU


Does not come on DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 10 second or more. (for Automatic Transmission: Keep the shift lever in D.)


h.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the battery temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

for Automatic Transmission:

Depress the brake pedal and stop the vehicle.

for Manual Transmission:

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control. (for Automatic Transmission: Keep the shift lever in D.)


f.

for Automatic Transmission:

Release the brake pedal with the shift lever in D to start the engine.

for Manual Transmission:

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A348496E04
1.333,1.375 4.25,1.594 2.917,0.219 10 false Certification ECU (Smart Key ECU Assembly) 1.333,1.229 1.792,1.427 0.458,0.198 10 false G69 2.656,0.865 3.271,1.063 0.615,0.198 10 false IG1D 3.063,0.719 3.375,0.917 0.313,0.198 10 false 20 1.885,0.844 2.198,1.042 0.313,0.198 10 false +B 1.677,0.75 1.833,0.948 0.156,0.198 10 false 1 0.073,0.052 2.594,0.313 2.521,0.26 12 false w/ Entry and Start System: 0.458,1.646 1.063,1.833 0.604,0.188 10 false SMART 2.292,3.885 3.156,4.104 0.865,0.219 10 false AM2 NO. 2 2.406,2.802 2.865,3 0.458,0.198 10 false IG2 2.052,2.406 2.208,2.604 0.156,0.198 10 false 2 2.875,2.417 3.031,2.615 0.156,0.198 10 false 1 2.885,2 3.042,2.198 0.156,0.198 10 false 3 2.063,2 2.219,2.198 0.156,0.198 10 false 5 0.698,4.813 1.469,5.01 0.771,0.198 10 false J/B-B 6.375,2.135 6.833,2.333 0.458,0.198 10 false ECM 6.271,1.5 6.885,1.698 0.615,0.198 10 false MREL 5.896,1.51 6.354,1.708 0.458,0.198 10 false G85 5.938,1.302 6.25,1.5 0.313,0.198 10 false 14 6.281,0.927 6.896,1.125 0.615,0.198 10 false IGSW 5.896,0.948 6.354,1.146 0.458,0.198 10 false G86 5.927,0.75 6.24,0.948 0.313,0.198 10 false 18 3.917,3.729 5.292,3.927 1.375,0.198 10 false IG2 NO. 1 3.26,3.417 3.573,3.615 0.313,0.198 10 false 2G 3.021,3.427 3.177,3.625 0.156,0.198 10 false 1 4.948,3.583 5.26,3.781 0.313,0.198 10 false 2G 5.01,3.396 5.167,3.594 0.156,0.198 10 false 2 4.948,3.99 5.26,4.188 0.313,0.198 10 false 2P 5.01,3.802 5.167,4 0.156,0.198 10 false 6 3.896,4.125 4.667,4.323 0.771,0.198 10 false METER 3.24,5.354 4.438,5.573 1.198,0.219 10 false EFI-MAIN NO. 2 2.281,4.823 3.479,5.042 1.198,0.219 10 false EFI-MAIN NO. 2 4.177,4.802 5.552,5 1.375,0.198 10 false EFI NO. 1 4.948,4.656 5.26,4.854 0.313,0.198 10 false 2G 5,4.438 5.156,4.635 0.156,0.198 10 false 3 1.771,4.656 2.083,4.854 0.313,0.198 10 false 2B 1.802,4.448 1.958,4.646 0.156,0.198 10 false 1 5.875,4.656 6.333,4.854 0.458,0.198 10 false G126 5.99,4.448 6.146,4.646 0.156,0.198 10 false 1 5.875,6.188 6.333,6.385 0.458,0.198 10 false G126 6.323,4.635 6.635,4.833 0.313,0.198 10 false +B 5.969,5.979 6.125,6.177 0.156,0.198 10 false 6 6.302,6.188 6.917,6.385 0.615,0.198 10 false DGND 5.865,3.979 6.323,4.177 0.458,0.198 10 false G127 5.948,3.781 6.26,3.979 0.313,0.198 10 false 18 6.313,3.979 6.771,4.177 0.458,0.198 10 false IG2 1.76,5.083 2.073,5.281 0.313,0.198 10 false 2J 1.802,4.885 1.958,5.083 0.156,0.198 10 false 5 1.771,6.219 2.083,6.417 0.313,0.198 10 false 2K 1.813,6.01 1.969,6.208 0.156,0.198 10 false 3 3.25,6.5 4.448,6.719 1.198,0.219 10 false EFI-MAIN NO. 1 2.25,5.958 3.448,6.177 1.198,0.219 10 false EFI-MAIN NO. 1 4.958,6.24 5.271,6.438 0.313,0.198 10 false 2P 4.99,6.042 5.146,6.24 0.156,0.198 10 false 8 4.948,5.813 5.26,6.01 0.313,0.198 10 false 2G 4.99,5.604 5.146,5.802 0.156,0.198 10 false 7 4.979,5.083 5.292,5.281 0.313,0.198 10 false 2P 5.01,4.875 5.167,5.073 0.156,0.198 10 false 9 0.438,5.969 1.51,6.167 1.073,0.198 10 false FL MAIN 0.573,6.833 1.646,7.031 1.073,0.198 10 false Battery 5.99,6.573 7.073,7.094 1.083,0.521 10 false Engine Stop and Start ECU 2.198,6.917 5.708,7.135 3.51,0.219 10 false Instrument Panel Junction Block Assembly 2.094,3.417 2.406,3.615 0.313,0.198 10 false 2G 1.833,3.417 1.99,3.615 0.156,0.198 10 false 6

A348497E03
0.885,1.406 3.115,1.667 2.229,0.26 10 false Ignition or Starter Switch Assembly 0.865,1.198 1.177,1.396 0.313,0.198 10 false G1 1.292,0.99 1.75,1.188 0.458,0.198 10 false AM2 2.51,0.979 2.969,1.177 0.458,0.198 10 false IG2 2.844,0.729 3,0.927 0.156,0.198 10 false 3 1.052,0.74 1.208,0.938 0.156,0.198 10 false 4 0.438,2.771 3.344,2.969 2.906,0.198 10 false STRG LOCK/AM2 NO. 1 0.063,0.042 6.115,0.281 6.052,0.24 12 false w/o Entry and Start System: 6.365,2.135 6.823,2.333 0.458,0.198 10 false ECM 6.281,0.917 6.896,1.115 0.615,0.198 10 false IGSW 5.896,0.938 6.354,1.135 0.458,0.198 10 false G86 5.927,0.74 6.24,0.938 0.313,0.198 10 false 18 5.896,1.5 6.354,1.698 0.458,0.198 10 false G85 5.927,1.313 6.24,1.51 0.313,0.198 10 false 14 6.281,1.49 6.896,1.688 0.615,0.198 10 false MREL 3.26,3.417 3.573,3.615 0.313,0.198 10 false 2G 3.01,3.427 3.167,3.625 0.156,0.198 10 false 1 3.885,3.74 4.646,3.948 0.76,0.208 10 false IG2 NO. 1 3.896,4.135 4.667,4.333 0.771,0.198 10 false METER 4.948,3.583 5.26,3.781 0.313,0.198 10 false 2G 4.99,3.385 5.146,3.583 0.156,0.198 10 false 2 4.958,3.99 5.271,4.188 0.313,0.198 10 false 2P 4.99,3.792 5.146,3.99 0.156,0.198 10 false 6 5.875,3.979 6.333,4.177 0.458,0.198 10 false G127 6.313,3.979 6.771,4.177 0.458,0.198 10 false IG2 5.969,3.781 6.281,3.979 0.313,0.198 10 false 18 5.885,4.646 6.344,4.844 0.458,0.198 10 false G126 6.323,4.646 6.781,4.844 0.458,0.198 10 false +B 5.99,4.427 6.146,4.625 0.156,0.198 10 false 1 3.229,5.323 4.333,5.531 1.104,0.208 10 false EFI-MAIN NO. 2 2.281,4.813 3.385,5.021 1.104,0.208 10 false EFI-MAIN NO. 2 4.208,4.823 5.583,5.021 1.375,0.198 10 false EFI NO. 1 4.938,4.656 5.25,4.854 0.313,0.198 10 false 2G 4.99,4.438 5.146,4.635 0.156,0.198 10 false 3 1.771,4.656 2.083,4.854 0.313,0.198 10 false 2B 1.823,4.427 1.979,4.625 0.156,0.198 10 false 1 1.76,5.073 2.073,5.271 0.313,0.198 10 false 2J 1.813,4.875 1.969,5.073 0.156,0.198 10 false 5 4.948,5.083 5.26,5.281 0.313,0.198 10 false 2P 5,4.875 5.156,5.073 0.156,0.198 10 false 9 4.938,5.813 5.25,6.01 0.313,0.198 10 false 2G 5,5.604 5.156,5.802 0.156,0.198 10 false 7 3.198,6.479 4.302,6.688 1.104,0.208 10 false EFI-MAIN NO. 1 2.229,5.979 3.333,6.188 1.104,0.208 10 false EFI-MAIN NO. 1 1.771,6.229 2.083,6.427 0.313,0.198 10 false 2K 1.823,6.021 1.979,6.219 0.156,0.198 10 false 3 4.958,6.24 5.271,6.438 0.313,0.198 10 false 2P 5.01,6.042 5.167,6.24 0.156,0.198 10 false 8 0.646,4.823 1.417,5.021 0.771,0.198 10 false J/B-B 0.427,5.969 1.5,6.167 1.073,0.198 10 false FL MAIN 5.885,6.188 6.344,6.385 0.458,0.198 10 false G126 5.99,5.979 6.146,6.177 0.156,0.198 10 false 6 6.292,6.198 6.906,6.396 0.615,0.198 10 false DGND 5.396,6.667 7.115,6.958 1.719,0.292 10 false Engine Stop and Start ECU 0.583,6.823 1.656,7.021 1.073,0.198 10 false Battery 2.188,6.938 5.594,7.146 3.406,0.208 10 false Instrument Panel Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

for Automatic Transmission:

When the engine stop and start ECU is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.

Powertrain > Stop and Start > Data List
Tester Display
IG Switch
50003 227 19

e.

Read the value displayed on the GTS.

Result:
Tester Display Result Proceed to
IG Switch OFF A
ON B




A

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G127 engine stop and start ECU connector.


b.

Disconnect the 2P instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-18 (IG2) - 2P-6 Always Below 1 Ω
G127-18 (IG2) - Body ground Always 10 kΩ or higher
2P-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG



OK (w/ Entry and Start System)

3.CHECK HARNESS AND CONNECTOR (IG2 RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

OK (w/o Entry and Start System)

17.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY AM2 TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IG2 RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2G instrument panel junction block assembly connector.


b.

Remove the IG2 relay from No. 4 relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2G-1 - IG2 relay terminal 3 Always Below 1 Ω
2G-1 - Body ground Always 10 kΩ or higher
IG2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RELAY (IG2 RELAY)

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BATTERY, BODY GROUND)

NG

REPLACE RELAY (IG2 RELAY)

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BATTERY, BODY GROUND)
A382138C01
0.698,0.188 1.01,0.385 0.313,0.198 10 false *1 3.563,0.115 3.875,0.313 0.313,0.198 10 false *2 0.604,1.073 0.917,1.271 0.313,0.198 10 false *3 4.302,0.823 4.615,1.021 0.313,0.198 10 false *3 2.083,1.271 2.396,1.469 0.313,0.198 10 false *a 5.594,1.438 5.906,1.635 0.313,0.198 10 false *a
*1 for RHD *2 for LHD
*3 No. 4 Relay Block ASSEMBLY - -
*a IG2 Relay Terminal - -


a.

Remove the IG2 relay from No. 4 relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
IG2 relay terminal 5 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG2 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (IG2 RELAY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IG2 RELAY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Remove the IG2 relay from No. 4 relay block assembly.


b.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G69-20 (ID1D) - IG2 relay terminal 1 Always Below 1 Ω
G69-20 (ID1D) - Body ground Always 10 kΩ or higher
IG2 relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) +B TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) +B TERMINAL VOLTAGE)
a.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


b.
A349010C02
1.458,0.323 1.917,0.531 0.458,0.208 0.698,1.01 0.5,0.667 0.5,0.667 0.417,0.667 true 0.125,0.125 0.438,0.323 0.313,0.198 10 false *a 0.177,0.594 0.49,0.792 0.313,0.198 10 false +B 1.563,0.354 2.021,0.552 0.458,0.198 10 false G69
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G69-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) IG1D TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) IG1D TERMINAL VOLTAGE)
a.
A348986C02
1.615,0.219 2.073,0.406 0.458,0.188 1.677,1.344 0.99,1.906 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 0.833,1.938 1.448,2.135 0.615,0.198 10 false IG1D 1.729,0.24 2.188,0.438 0.458,0.198 10 false G69
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G69-20 (IG1D) - Body ground Ignition switch ACC Below 1 V
Ignition switch ON 9 V or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G126 engine stop and start ECU connector.


b.

Disconnect the 2G instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G126-1 (+B) - 2G-3 Always Below 1 Ω
G126-1 (+B) - Body ground Always 10 kΩ or higher
2G-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY))
a.

Disconnect the 2P and 2G instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-9 - 2G-7 Always Below 1 Ω
2P-9 - Body ground Always 10 kΩ or higher
2G-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY, BODY GROUND)
A349049C01
1.063,0.125 1.448,0.417 0.385,0.292 5.531,0.156 5.917,0.448 0.385,0.292 3.302,0.146 3.688,0.438 0.385,0.292 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 1.177,0.198 1.49,0.396 0.313,0.198 10 false 2B 5.646,0.219 5.958,0.417 0.313,0.198 10 false 2K 3.427,0.208 3.74,0.406 0.313,0.198 10 false 2J
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
- -


a.

Disconnect the instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2B-1 - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2J-5 - Body ground Always Below 1 Ω
2K-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK ECM (IGSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK ECM (IGSW TERMINAL VOLTAGE)
a.

Disconnect the G86 ECM connector.


F100903C02
1.448,0.792 1.958,1.083 0.51,0.292 1.042,2.344 0.656,2.344 true 0.302,0.281 0.615,0.479 0.313,0.198 10 false *a 1.583,0.865 2.042,1.063 0.458,0.198 10 false G86 0.219,2.271 0.833,2.469 0.615,0.198 10 false IGSW
*a Front view of wire harness connector
(to ECM)


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G86-18 (IGSW) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - ECM)

NG

16.CHECK HARNESS AND CONNECTOR (ECM - INSTRUMENT PANEL JUNCTION BLOCK)
13.CHECK HARNESS AND CONNECTOR (EFI-MAIN RELAY - ECM)
a.

Disconnect the 2P instrument panel junction block assembly connector.


b.

Disconnect the G85 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-8 - G85-14 (MREL) Always Below 1 Ω
2P-8 - Body ground Always 10 kΩ or higher
G85-14 (MREL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

14.INSPECT ECM (MREL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT ECM (MREL VOLTAGE)
a.
A348466C33
2.281,0.375 2.656,0.615 0.375,0.24 2.688,1.688 2.375,1.063 true 2.333,0.417 2.667,0.583 0.333,0.167 10 false G85 2.469,1.729 3.208,1.927 0.74,0.198 10 false 14 (MREL) 0.094,0.052 0.323,0.271 0.229,0.219 10 false *a
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G85-14 (MREL) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1 RELAY, EFI-MAIN NO. 2 RELAY)

NG

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (EFI-MAIN NO. 1 RELAY, EFI-MAIN NO. 2 RELAY)
a.

Inspect instrument panel junction block assembly (EFI-MAIN NO. 1 relay, EFI-MAIN NO. 2 relay).

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>RELAY(w/ Urea SCR System)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (ECM - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the 2G instrument panel junction block connector.


b.

Disconnect the G86 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-18 (IGSW) - 2G-2 Always Below 1 Ω
G86-18 (IGSW) - Body ground Always 10 kΩ or higher
2G-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY AM2 TERMINAL VOLTAGE)
a.

Disconnect the ignition or starter switch assembly connector.


b.
E118422C01
1.396,0.854 1.948,1.063 0.552,0.208 2.177,2 2.417,1.25 2.417,1.25 2.583,1.25 true 0.177,0.219 0.49,0.417 0.313,0.198 10 false *a 1.573,0.865 1.885,1.063 0.313,0.198 10 false G1 2.646,1.167 3.104,1.365 0.458,0.198 10 false AM2
*a Front view of wire harness connector
(to Ignition or Starter Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2GD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

19.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2G instrument panel junction block assembly connector.


b.
A349038C01
1.427,0.156 1.885,0.458 0.458,0.302 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.563,0.24 1.875,0.438 0.313,0.198 10 false 2G
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2G-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR