Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
JUNCTION CONNECTOR
No. 1 CAN Junction Connector
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | for Brake Actuator Assembly (Skid Control ECU) |
| *c | for Airbag Sensor Assembly | *d | for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) |
| *e | for Combination Meter Assembly | *f | for No. 2 CAN Junction Connector |
| *g | for Engine Stop and Start ECU (w/ Stop and Start System) | *h | for Headlight Leveling ECU Assembly (for LED Headlight or w/ Headlight Cleaner System) |
| *i | for Central Gateway ECU (Network Gateway ECU) | *j | ·
for Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System) ·
for Air Conditioning Amplifier Assembly (for Manual Air Conditioning System) |
| No. 1 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
|
*1: w/ Stop and Start System *2: for LED Headlight or w/ Headlight Cleaner System *3: for Automatic Air Conditioning System *4: for Manual Air Conditioning System |
||
| G67-1 (CANH) | B | Brake actuator assembly (skid control ECU) |
| G67-11 (CANL) | W | |
| G67-2 (CANH) | Y | Airbag sensor assembly |
| G67-12 (CANL) | W | |
| G67-3 (CANH) | BE | Spiral with sensor cable sub-assembly (steering angle sensor) |
| G67-13 (CANL) | W | |
| G67-5 (CANH) | SB | Combination meter assembly |
| G67-15 (CANL) | W | |
| G67-6 (CANH) | LG | No. 2 CAN junction connector |
| G67-16 (CANL) | W | |
| G67-7 (CANH) | P | Engine stop and start ECU*1 |
| G67-17 (CANL) | W | |
| G67-8 (CANH) | V | Headlight leveling ECU assembly*2 |
| G67-18 (CANL) | W | |
| G67-9 (CANH) | R | Central gateway ECU (network gateway ECU) |
| G67-19 (CANL) | W | |
| G67-10 (CANH) | GR | Air conditioning amplifier assembly*3, *4 |
| G67-20 (CANL) | W | |
No. 2 CAN Junction Connector
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) |
| *c | for 4 Wheel Drive Control ECU (for 4WD) | *d | for ECM |
| *e | for No. 1 CAN Junction Connector | - | - |
| No. 2 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
|
*1: w/ Entry and Start System *2: for 4WD |
||
| G68-3 (CANH) | G | Certification ECU (smart key ECU assembly)*1 |
| G68-13 (CANL) | W | |
| G68-4 (CANH) | R | 4 wheel drive control ECU*2 |
| G68-14 (CANL) | W | |
| G68-5 (CANH) | B | ECM |
| G68-15 (CANL) | W | |
| G68-6 (CANH) | LG | No. 1 CAN junction connector |
| G68-16 (CANL) | W | |
No. 3 CAN Junction Connector
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | for Forward Recognition Camera |
| *c | for Millimeter Wave Radar Sensor Assembly | *d | for Central Gateway ECU (Network Gateway ECU) |
| No. 3 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| G131-4 (CANH) | Y | Forward recognition camera |
| G131-14 (CANL) | W | |
| G131-5 (CANH) | R | Millimeter wave radar sensor assembly |
| G131-15 (CANL) | W | |
| G131-6 (CANH) | G | Central gateway ECU (network gateway ECU) |
| G131-16 (CANL) | W | |
| G131-7 (CANH) | L | |
| G131-17 (CANL) | W |
No. 4 CAN Junction Connector
| *1 | No. 4 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector
(to No. 4 CAN Junction Connector) |
- | - |
| No. 4 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
|
*1: w/ Navigation System *2: w/ Audio and Visual System (for Radio and Display Type) |
||
| G132-1 (CANH) | V | ·
Navigation receiver assembly*1 ·
Radio and display receiver assembly*2 |
| G132-2 (CANL) | W | |
| G133-1 (CANH) | V | Central gateway ECU (network gateway ECU) |
| G133-2 (CANL) | W | |
| G135-1 (CANH) | P | |
| G135-2 (CANL) | W | |
CHECK DLC3
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click here
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G8-6 (CANH) - G8-14 (CANL) | L - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G8-6 (CANH) - G8-4 (CG) | L - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G8-14 (CANL) - G8-4 (CG) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G8-6 (CANH) - G8-16 (BAT) | L - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G8-14 (CANL) - G8-16 (BAT) | W - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *A | V Bus | *B | Bus 2 |
| *C | Bus 3 | *D | Bus 5 |
| *a | Component without harness connected
(Central Gateway ECU [Network Gateway ECU]) |
- | - |
| *A | Bus 2 |
| *B | Bus 3 |
| *C | Bus 5 |
| *D | V Bus |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G128-14 (CA6H) - G128-5 (CA6L) | L - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| G128-14 (CA6H) - G128-10 (GND) | L - B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-5 (CA6L) - G128-10 (GND) | W - B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-14 (CA6H) - G128-1 (BATT) | L - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G128-5 (CA6L) - G128-1 (BATT) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G128-18 (CA4H) - G128-17 (CA4L) | R - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G128-18 (CA4H) - G128-10 (GND) | R - B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-17 (CA4L) - G128-10 (GND) | W - B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-18 (CA4H) - G128-1 (BATT) | R - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G128-17 (CA4L) - G128-1 (BATT) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G128-6 (CA3H) - G128-21 (CA3L) | P - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| G128-6 (CA3H) - G128-19 (CAYH) | P - V | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G128-21 (CA3L) - G128-20 (CAYL) | W - W | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G128-6 (CA3H) - G128-10 (GND) | P - B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-21 (CA3L) - G128-10 (GND) | W - B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-6 (CA3H) - G128-1 (BATT) | P - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G128-21 (CA3L) - G128-1 (BATT) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G128-15 (CA5H) - G128-16 (CA5L) | G - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| G128-15 (CA5H) - G128-9 (CAXH) | G - L | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G128-16 (CA5L) - G128-24 (CAXL) | W - W | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| G128-15 (CA5H) - G128-10 (GND) | G - B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-16 (CA5L) - G128-10 (GND) | W - B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G128-15 (CA5H) - G128-1 (BATT) | G - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G128-16 (CA5L) - G128-1 (BATT) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK ECM
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>TERMINALS OF ECM
Disconnect the ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G85-17 (CANH) - G85-28 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G85-17 (CANH) - C60-1 (E1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G85-28 (CANL) - C60-1 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G85-17 (CANH) - G86-1 (BATT) | B - Y | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G85-28 (CANL) - G86-1 (BATT) | W - Y | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G9-36 (CANH) - G9-35 (CANL) | SB - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G9-36 (CANH) - G9-27 (EP) | SB - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G9-35 (CANL) - G9-27 (EP) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G9-36 (CANH) - G9-21 (B) | SB - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G9-35 (CANL) - G9-21 (B) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>TERMINALS OF ECU
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the airbag sensor assembly connector.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G42-13 (CANH) - G42-22 (CANL) | Y - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G42-13 (CANH) - G42-25 (E1) | Y - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G42-22 (CANL) - G42-25 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G42-13 (CANH) - G8-16 (BAT) | Y - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G42-22 (CANL) - G8-16 (BAT) | W - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
Refer to Terminals of ECU.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TERMINALS OF ECU
Disconnect the brake actuator assembly (skid control ECU) connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A4-22 (CANH) - A4-10 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A4-22 (CANH) - A4-25 (GND1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A4-10 (CANL) - A4-25 (GND1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A4-22 (CANH) - A4-13 (BM) | B - R | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A4-10 (CANL) - A4-13 (BM) | W - R | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)
| *a | Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor]) |
Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G21-3 (CANH) - G21-2 (CANL) | BE - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G21-3 (CANH) - G21-1 (ESS) | BE - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G21-2 (CANL) - G21-1 (ESS) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G21-3 (CANH) - G21-5 (BAT) | BE - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G21-2 (CANL) - G21-5 (BAT) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
Refer to Terminals of ECU.
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G70-40 (CANH) - G70-18 (CANL) | G - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G70-40 (CANH) - G69-10 (E) | G - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G70-18 (CANL) - G69-10 (E) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G70-40 (CANH) - G69-1 (+B) | G - P | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G70-18 (CANL) - G69-1 (+B) | W - P | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])
Refer to Terminals of ECU.
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G37-9 (CANH) - G37-10 (CANL) | V - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G37-9 (CANH) - G40-7 (GND1) | V - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G37-10 (CANL) - G40-7 (GND1) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G37-9 (CANH) - G40-4 (+B1) | V - SB | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G37-10 (CANL) - G40-4 (+B1) | W - SB | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector
(to Navigation Receiver assembly) |
Disconnect the navigation receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G113-9 (CANH) - G113-10 (CANL) | V - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G113-9 (CANH) - G115-7 (GND1) | V - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G113-10 (CANL) - G115-7 (GND1) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G113-9 (CANH) - G115-4 (+B1) | V - SB | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G113-10 (CANL) - G115-4 (+B1) | W - SB | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK 4 WHEEL DRIVE CONTROL ECU (for 4WD)
Refer to Terminals of ECU.
Click hereDrivetrain>VF2CM TRANSFER / 4WD / AWD>TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector
(to 4 Wheel Drive Control ECU) |
Disconnect the 4 wheel drive control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C39-20 (CANH) - C39-40 (CANL) | R - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| C39-20 (CANH) - C40-10 (GND) | R - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C39-40 (CANL) - C40-10 (GND) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C39-20 (CANH) - C39-21 (+B) | R - L | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| C39-40 (CANL) - C39-21 (+B) | W - L | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
Refer to Terminals of ECU.
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G33-11 (TX+) - G33-12 (TX-) | GR - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G33-11 (TX+) - G33-14 (GND) | GR - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G33-12 (TX-) - G33-14 (GND) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G33-11 (TX+) - G33-21 (B) | GR - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G33-12 (TX-) - G33-21 (B) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)
Refer to Terminals of ECU.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
| *b | Front view of DLC3 |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G77-8 (TX+) - G77-9 (TX-) | GR - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G77-8 (TX+) - G77-23 (GND) | GR - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G77-9 (TX-) - G77-23 (GND) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G77-8 (TX+) - G8-16 (BAT) | GR - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G77-9 (TX-) - G8-16 (BAT) | W - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight or w/ Headlight Cleaner System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector
(to Headlight Leveling ECU Assembly) |
| *b | Front view of DLC3 |
Disconnect the headlight leveling ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G80-6 (CANH) - G80-7 (CANL) | V - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G80-6 (CANH) - G80-9 (E1) | V - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G80-7 (CANL) - G80-9 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G80-6 (CANH) - G8-16 (BAT) | V - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G80-7 (CANL) - G8-16 (BAT) | W - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK ENGINE STOP AND START ECU (w/ Stop and Start System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector
(to Engine Stop and Start ECU) |
Disconnect the engine stop and start ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G127-13 (CANH) - G127-14 (CANL) | P - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G127-13 (CANH) - G125-8 (GND1) | P - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G127-14 (CANL) - G125-8 (GND1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G127-13 (CANH) - G125-3 (BIN1) | P - R | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G127-14 (CANL) - G125-3 (BIN1) | W - R | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK FORWARD RECOGNITION CAMERA
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
| *b | Front view of DLC3 |
Disconnect the forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| Q4-5 (CA1P) - Q4-11 (CA1N) | B - V | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Q4-5 (CA1P) - Q4-10 (GND) | B - B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q4-11 (CA1N) - Q4-10 (GND) | V - B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q4-5 (CA1P) - G8-16 (BAT) | B - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Q4-11 (CA1N) - G8-16 (BAT) | V - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A64-3 (CA2H) - A64-2 (CA2L) | R - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A64-3 (CA2H) - A64-1 (SGND) | R - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A64-2 (CA2L) - A64-1 (SGND) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A64-3 (CA2H) - G8-16 (BAT) | R - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A64-2 (CA2L) - G8-16 (BAT) | W - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |