Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT FLOOR AIRBAG SENSOR › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0262547 FRONT FLOOR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT FLOOR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89837 1.INSTALL FRONT FLOOR SIDE AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) terminal of the battery, the airbag may deploy even if an impact is applied only to the front floor side airbag sensor. Therefore, make sure that the negative (-) terminal of the battery is disconnected before performing this procedure.




c.
B443138C01
0.052,0.042 0.313,0.271 0.26,0.229 12 true *A 0.052,2.24 0.594,2.635 0.542,0.396 12 false *B
*A for Single Cab, Smart Cab
*B for Double Cab


Attach the guide and hold the front floor side airbag sensor in place.


d.

Install the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the front floor side airbag sensor has been dropped, replace it with a new one.

·

When installing the front floor side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the bolt while holding the front floor side airbag sensor because the front floor side airbag sensor guide is easily damaged.




e.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B340848C02
4.583,0.594 4.896,0.75 0.313,0.156 10 *a 4.677,1.875 4.99,2.031 0.313,0.156 10 *b 1.385,0.615 1.698,0.771 0.313,0.156 10 *a 1.448,1.865 1.76,2.021 0.313,0.156 10 *b
*a Correct *b Incorrect



f.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.


B399097C02
2.396,1.031 2.813,0.615 true 2.479,1.802 2.479,1.385 true 2.26,0.813 2.677,0.396 true 2.708,0.281 3.021,0.438 0.313,0.156 10 false *c 5.917,2.208 6.229,2.365 0.313,0.156 10 false *d 2.875,0.51 3.188,0.667 0.313,0.156 10 false *a 2.417,1.844 2.729,2 0.313,0.156 10 false *b
*a Housing Lock *b CPA
*c CPA Upper Part *d Connection is Completed
V113147

Connect Direction - -




g.

Check that there is no looseness in the installation parts of the front floor side airbag sensor.


Hide 62414A 2.INSTALL LOWER CENTER PILLAR GARNISH LH (for Double Cab)

Hide 67918A 3.INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab)

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION