Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2016.03
RM3250E _51 Engine / Hybrid System _037980 CRUISE CONTROL _0262560 LANE DEPARTURE ALERT SYSTEM C

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  


DESCRIPTION

The forward recognition camera communicates with the millimeter wave radar sensor assembly via CAN communication. If there is a communication error with the millimeter wave radar sensor assembly, the forward recognition camera stores DTC U0235.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor When the vehicle is being driven at a speed of 5 km/h (4 mph) or more 2 seconds after the ignition switch is turned to ON, a communication error between the millimeter wave radar sensor assembly and the forward recognition camera is detected for approximately 5 seconds.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Forward recognition camera



WIRING DIAGRAM

C355486E01
0.24,3.448 4.823,3.646 4.583,0.198 10 false from Engine Stop and Start ECU 1.344,2.792 3.635,2.99 2.292,0.198 10 false from IG Circuit 2.646,2.969 4.021,3.167 1.375,0.198 10 false IG1 NO. 5 5.229,1 5.688,1.198 0.458,0.198 10 false IGB 5.24,2.813 5.698,3.01 0.458,0.198 10 false IGB 5.25,3.833 5.865,4.031 0.615,0.198 10 false SGND 5.219,0.615 5.833,0.813 0.615,0.198 10 false GND 4.813,1.656 6.635,1.875 1.823,0.219 10 false Forward Recognition Camera 4.458,4.188 7.125,4.469 2.667,0.281 10 false Millimeter Wave Radar Sensor Assembly 0.344,4.281 4.01,4.479 3.667,0.198 10 false : CAN Communication Line 3.354,2.698 3.667,2.896 0.313,0.198 10 false *1 3.365,3.323 3.677,3.521 0.313,0.198 10 false *2 0.24,0.448 4.521,0.646 4.281,0.198 10 false *1: w/o Stop and Start System 0.24,0.865 4.521,1.063 4.281,0.198 10 false *2: w/ Stop and Start System 4.927,0.51 5.24,0.708 0.313,0.198 10 false 10 4.969,0.896 5.281,1.094 0.313,0.198 10 false 7 4.802,1.5 5.115,1.698 0.313,0.198 10 false Q4 5.896,0.385 6.51,0.583 0.615,0.198 10 false CANH 5.906,1.24 6.521,1.438 0.615,0.198 10 false CANL 6.417,0.188 6.573,0.385 0.156,0.198 10 false 6 6.385,1.042 6.698,1.24 0.313,0.198 10 false 12 4.469,4.031 4.927,4.229 0.458,0.198 10 false A64 5.021,2.688 5.177,2.885 0.156,0.198 10 false 8 5.021,3.698 5.177,3.896 0.156,0.198 10 false 1 5.958,3.083 6.573,3.281 0.615,0.198 10 false CA1N 6.448,2.885 6.604,3.083 0.156,0.198 10 false 6 5.958,3.583 6.573,3.781 0.615,0.198 10 false CA1P 6.458,3.385 6.615,3.583 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

w/o Stop and Start System:

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECUs and sensors to communicate using the CAN communication system. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

B

2.CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)
HINT:

When pre-crash safety system DTC U023A or U1002 is output, check that the local bus is functioning normally by performing the diagnostic procedure for U023A or U1002.


a.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC U023A and U1002 are not output A
DTC U023A or U1002 is output B



A

3.CHECK FOR OPEN IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)

B

3.CHECK FOR OPEN IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.


c.
C351772C08
1.563,0.177 1.938,0.448 0.375,0.271 1.781,1.823 2.073,1.458 true 2.156,1.125 2.448,0.76 true 2.469,0.625 2.927,0.823 0.458,0.198 10 false CANH 1.656,0.229 2.115,0.427 0.458,0.198 10 false Q4 0.156,0.156 0.615,0.354 0.458,0.198 10 false *a 1.615,1.865 2.073,2.063 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-6 (CANH) - Q4-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


HINT:

If the result is not as specified, a malfunction in a CAN communication line is suspected.



e.

Connect the forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (FORWARD RECOGNITION CAMERA))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAN BUS LINE)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (FORWARD RECOGNITION CAMERA))
a.
C351772C10
1.563,0.177 1.938,0.448 0.375,0.271 0.979,1.781 1.271,1.417 true 0.844,1.813 1.302,2.01 0.458,0.198 10 false IGB 1.646,0.229 2.104,0.427 0.458,0.198 10 false Q4 0.156,0.156 0.615,0.354 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

Q4-7 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2



d.

Connect the forward recognition camera connector.


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BODY GROUND)
a.
C351772C11
1.563,0.177 1.938,0.448 0.375,0.271 2.104,1.813 1.802,1.469 true 1.646,0.229 2.104,0.427 0.458,0.198 10 false Q4 0.156,0.156 0.615,0.354 0.458,0.198 10 false *a 2.021,1.844 2.479,2.042 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-10 (GND) - Body ground Always Below 1 Ω



c.

Connect the forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY))
a.
E325539C71
1.563,0.156 1.938,0.385 0.375,0.229 2.573,1.688 1.958,1.25 true 1.625,0.198 2.083,0.396 0.458,0.198 10 false A64 2.521,1.698 2.979,1.896 0.458,0.198 10 false IGB 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

A64-8 (IGB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2



c.

Connect the millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

7.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
E325539C72
1.563,0.156 1.938,0.385 0.375,0.229 1.396,1.042 0.771,1.563 true 1.625,0.198 2.083,0.396 0.458,0.198 10 false A64 0.125,0.135 0.438,0.292 0.313,0.156 10 false *a 0.531,1.583 1.021,1.781 0.49,0.198 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (SGND) - Body ground Always Below 1 Ω



c.

Connect the millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
9.CHECK FOR DTCs (LANE DEPARTURE ALERT SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > LKA/LDA > Clear DTCs
50002 355

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR

Chassis > LKA/LDA > Trouble Codes
50001 355

Result:
Result Proceed to
DTC U0235 is not output A
DTC U0235 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

10.REPLACE FORWARD RECOGNITION CAMERA
10.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

END