Home › Engine / Hybrid System › 2GD-FTV INTAKE / EXHAUST › EXHAUST PIPE(for Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038009 2GD-FTV INTAKE / EXHAUST _0262587 EXHAUST PIPE(for Urea SCR System) A

2GD-FTV INTAKE / EXHAUST  EXHAUST PIPE(for Urea SCR System)  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

NOTICE:
A380556

Do not hold the front exhaust pipe assembly at the location shown in the illustration. Otherwise, it may become deformed or damaged, adversely affecting its thermal insulation capabilities.


a.
A111834

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

40 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.


b.
A111803C07
2.854,0.656 2.281,0.25 2.281,0.25 2.167,0.25 true 2.833,1.083 2.833,1.479 true 1.99,0.156 2.26,0.417 0.271,0.26 10 false *1 2.771,1.51 3.042,1.729 0.271,0.219 10 false *2
*1 Gasket
*2 Exhaust Manifold Converter Sub-assembly


Install a new gasket to the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




c.
A076194C38
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.271,1.781 1.49,1.958 0.219,0.177 10 false *1 3.104,0.875 3.323,1.052 0.219,0.177 10 false *a
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap on a new gasket until its surface is flush with the exhaust manifold converter sub-assembly.


d.

Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts.


e.

Using a 14 mm union nut wrench, tighten the 2 bolts.

Torque:
Specified tightening torque : 43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 37.8 N*m (385 kgf*cm, 28 ft.*lbf)




f.

Install the No. 1 exhaust pipe support to the front exhaust pipe assembly.


Hide 51204 4.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY (for Automatic Transmission)

Hide 89460B 5.INSTALL NITROGEN OXIDES SENSOR ASSEMBLY

Hide 17430 7.INSTALL TAILPIPE ASSEMBLY

a.

for TSAM Made:

Install the tailpipe assembly to the 3 exhaust pipe supports.


b.

for TMT Made:

Install the tailpipe assembly to the 4 exhaust pipe supports.


c.

Install a new gasket and connect the tailpipe assembly to the front exhaust pipe assembly with the 2 bolts and 2 new nuts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

Do not reuse the gasket.



Hide 8.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.