Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY(for Double Cab) › from 2016.03
RM3250E _58 Vehicle Interior _038072 SEAT BELT _0185619 REAR SEAT OUTER BELT ASSEMBLY(for Double Cab) A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY(for Double Cab)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat ouer belt assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

for Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR SEAT ASSEMBLY

Hide 67914B 4.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 73178B 5.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 62514A 6.REMOVE LOWER QUARTER TRIM PANEL LH

Hide 73370C 7.REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

B415710

a.

Remove the bolt and disconnect the floor anchor of the rear No. 1 seat outer belt assembly LH.


b.
B415711

Remove the bolt and disconnect the shoulder anchor of the rear No. 1 seat outer belt assembly LH.


c.
B415712

w/o Pretensioner:

i.

Remove the 2 bolts.


ii.

Detach the 2 guides and remove the rear No. 1 seat outer belt assembly LH.



d.
B440583C01
0.958,0.604 1.26,0.469 false 1.344,0.396 1.656,0.594 0.313,0.198 10 false *1
*1 Locking Button
V100155

Protective Tape


w/ Pretensioner:

i.

Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.


ii.
B440584

Remove the 2 bolts.


iii.

Detach the 2 guides and remove the rear No. 1 seat outer belt assembly LH.