Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0189246 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 62180A 1.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Attach the clip to set the curtain shield airbag assembly LH in place.


d.

Temporarily install the 2 new bolts.


e.

Install the clip.

HINT:

Use the same procedure for the other clip.


i.

Attach the claw to connect a new clip.

NOTICE:

At this time, do not push in the pin to lock the clip.



ii.

Check that the deployment portion of the curtain shield airbag assembly LH is not twisted.


iii.
B407342C01
1.802,0.604 2.25,0.604 true 2.313,0.5 2.625,0.656 0.313,0.156 10 false *a
*a Pin
V113147

Push in this Direction


Push in the pin to lock the clip.


iv.

Lightly pull on the clip to check whether it is locked.



f.

for Single Cab:

Tighten the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

B409646N01
1.333,1.188 1.542,1.427 0.208,0.24 10 true (1) 1,0.865 1.208,1.104 0.208,0.24 10 true (2)


g.

for Double Cab:

Tighten the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

B409647N01
2.75,1.333 2.958,1.542 0.208,0.208 10 true (1) 2.385,1.333 2.594,1.542 0.208,0.208 10 true (2)


h.

for Smart Cab:

Tighten the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

B409648N01
2.094,1.156 2.344,1.396 0.25,0.24 10 true (1) 1.646,1.177 1.896,1.417 0.25,0.24 10 true (2)


i.
B409649C01
2.646,0.635 2.146,0.302 true 1.958,0.177 2.271,0.333 0.313,0.156 10 false *a
*a Connector Lock
V113147

Push in this Direction


Connect the airbag connector and push the connector lock.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION