Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › from 2016.08
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0278511 ECD SYSTEM(w/o EGR Cooler) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P064C  Glow Plug Control Module  P066B  Cylinder 1 Glow Plug Control Circuit High  P066D  Cylinder 2 Glow Plug Control Circuit High  P066F  Cylinder 3 Glow Plug Control Circuit High  P0671  Cylinder 1 Glow Plug Circuit/Open  P0672  Cylinder 2 Glow Plug Circuit/Open  P0673  Cylinder 3 Glow Plug Circuit/Open  P0674  Cylinder 4 Glow Plug Circuit/Open  P067B  Cylinder 4 Glow Plug Control Circuit High  P166F  Glow Plug Control Module Circuit Short  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P064C Glow Plug Control Module The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (1 trip detection logic). Glow plug controller - DTC stored
P066B Cylinder 1 Glow Plug Control Circuit High A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug

·

Short in No. 1 glow plug circuit


- DTC stored
P066D Cylinder 2 Glow Plug Control Circuit High A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug

·

Short in No. 2 glow plug circuit


- DTC stored
P066F Cylinder 3 Glow Plug Control Circuit High A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug

·

Short in No. 3 glow plug circuit


- DTC stored
P0671 Cylinder 1 Glow Plug Circuit/Open An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug

·

Open in No. 1 glow plug circuit

·

GLOW relay


- DTC stored
P0672 Cylinder 2 Glow Plug Circuit/Open An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug

·

Open in No. 2 glow plug circuit

·

GLOW relay


- DTC stored
P0673 Cylinder 3 Glow Plug Circuit/Open An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug

·

Open in No. 3 glow plug circuit

·

GLOW relay


- DTC stored
P0674 Cylinder 4 Glow Plug Circuit/Open An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug

·

Open in No. 4 glow plug circuit

·

GLOW relay


- DTC stored
P067B Cylinder 4 Glow Plug Control Circuit High A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug

·

Short in No. 4 glow plug circuit


- DTC stored
P166F Glow Plug Control Module Circuit Short A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (1 trip detection logic).
·

Glow plug controller

·

Short in glow plug circuit


- DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P064C Enter check mode
P066B
P066D
P066F
P067B
P0671
P0672
P0673
P0674
P166F

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P0671, P0672, P0673 and/or P0674 is output A
P066B, P066D, P066F and/or P067B is output B
P064C and/or P166F is output C




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)

B

13.CHECK HARNESS AND CONNECTOR

C

18.CHECK HARNESS AND CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)
a.
A241159C14
0.646,1.115 1.063,1.417 0.417,0.302 1.927,1.719 1.76,1.24 true 0.167,0.219 0.479,0.417 0.313,0.198 10 false *a 0.74,1.188 1.052,1.385 0.313,0.198 10 false A56 1.979,1.656 2.594,1.854 0.615,0.198 10 false BATT
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A56-1(BATT) - Body ground IG ON 11 to 14 V



c.

Reconnect the glow plug controller connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR

NG

8.INSPECT GLOW RELAY
3.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A348991C09
2.573,1.26 3.031,1.563 0.458,0.302 4.823,1.219 5.281,1.521 0.458,0.302 1.167,2.583 1.5,2.26 1.5,2.26 1.625,2.26 true 1.438,1.917 1.771,1.594 1.771,1.594 1.896,1.594 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.021,0.573 2.354,0.25 2.354,0.25 2.479,0.25 true 3.729,1.438 3.917,1.896 true 6.021,1.49 6.208,1.948 true 3.438,1.479 3.188,1.948 true 5.677,1.479 5.427,1.948 true 1.094,0.344 1.406,0.542 0.313,0.198 10 false *1 2.552,0.188 2.865,0.385 0.313,0.198 10 false 4 2.271,0.854 2.583,1.052 0.313,0.198 10 false 3 1.969,1.5 2.281,1.698 0.313,0.198 10 false 2 1.698,2.198 2.01,2.396 0.313,0.198 10 false 1 2.677,1.323 2.99,1.521 0.313,0.198 10 false C98 4.917,1.292 5.292,1.521 0.375,0.229 10 false C97 4.948,0.813 5.26,1.01 0.313,0.198 10 false *b 2.917,0.667 3.229,0.865 0.313,0.198 10 false *a 3.063,1.958 3.479,2.167 0.417,0.208 10 false GL1 3.823,1.948 4.323,2.177 0.5,0.229 10 false GL2 5.208,1.958 5.521,2.156 0.313,0.198 10 false GL3 6.188,1.969 6.5,2.167 0.313,0.198 10 false GL4
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C98-1 (GL1) - No. 1 glow plug connector terminal 1 Always Below 1 Ω
C98-2 (GL2) - No. 1 glow plug connector terminal 2 Always Below 1 Ω
C97-1 (GL3) - No. 1 glow plug connector terminal 3 Always Below 1 Ω
C97-2 (GL4) - No. 1 glow plug connector terminal 4 Always Below 1 Ω



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT GLOW PLUG

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT GLOW PLUG
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

b.

Exchange the glow plugs of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTCs (that have been erased) A
Other DTCs B


HINT:

Check for DTCs in check mode.




A

19.REPLACE GLOW PLUG CONTROLLER

B

5.REPLACE GLOW PLUG
5.REPLACE GLOW PLUG
a.

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

8.INSPECT GLOW RELAY

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR

NG

12.REPLACE GLOW RELAY
9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Remove the GLOW relay from the engine room relay block and junction block.


d.

Disconnect connectors of the glow plug controller.


e.

Disconnect the ECM connectors.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GLOW relay terminal 5- Battery positive terminal Always Below 1 Ω
GLOW relay terminal 1 - Body ground Always Below 1 Ω
GLOW relay terminal 3 - A56-1 (BATT) Always Below 1 Ω
GLOW relay terminal 2 - G85-15 (GREL) Always Below 1 Ω
GLOW relay terminal 5 or Battery positive terminal - Body ground andother terminals Always 10 kΩ or higher
GLOW relay terminal 3 or A56-1 (BATT) - Body ground andother terminals Always 10 kΩ or higher
GLOW relay terminal 2 or G85-15 (GREL) - Body ground andother terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE GLOW RELAY
a.

Replace the GLOW relay.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A348991C10
2.573,1.26 3.031,1.563 0.458,0.302 4.823,1.219 5.281,1.521 0.458,0.302 1.167,2.583 1.5,2.26 1.5,2.26 1.625,2.26 true 1.438,1.917 1.771,1.594 1.771,1.594 1.896,1.594 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.021,0.573 2.354,0.25 2.354,0.25 2.479,0.25 true 3.729,1.438 3.917,1.896 true 6.021,1.49 6.208,1.948 true 3.438,1.479 3.188,1.948 true 5.677,1.479 5.427,1.948 true 1.094,0.344 1.406,0.542 0.313,0.198 10 false *1 2.552,0.188 2.865,0.385 0.313,0.198 10 false 4 2.271,0.854 2.583,1.052 0.313,0.198 10 false 3 1.969,1.5 2.281,1.698 0.313,0.198 10 false 2 1.698,2.198 2.01,2.396 0.313,0.198 10 false 1 2.677,1.323 2.99,1.521 0.313,0.198 10 false C98 4.917,1.292 5.292,1.521 0.375,0.229 10 false C97 4.948,0.813 5.26,1.01 0.313,0.198 10 false *b 2.917,0.667 3.229,0.865 0.313,0.198 10 false *a 3.063,1.958 3.479,2.167 0.417,0.208 10 false GL1 3.823,1.948 4.323,2.177 0.5,0.229 10 false GL2 5.208,1.958 5.521,2.156 0.313,0.198 10 false GL3 6.188,1.969 6.5,2.167 0.313,0.198 10 false GL4
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C98-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always 10 kΩ or higher
C98-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always 10 kΩ or higher
C97-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always 10 kΩ or higher
C97-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.


Result:
Proceed to
OK
NG



OK

14.REPLACE GLOW PLUG CONTROLLER

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2GD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

No DTC is output.


HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

17.REPLACE GLOW PLUG
17.REPLACE GLOW PLUG
a.

Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.CHECK HARNESS AND CONNECTOR
a.

Disconnect connectors of the glow plug controller.

A348991C11
2.573,1.26 3.031,1.563 0.458,0.302 4.823,1.219 5.281,1.521 0.458,0.302 1.167,2.583 1.5,2.26 1.5,2.26 1.625,2.26 true 1.438,1.917 1.771,1.594 1.771,1.594 1.896,1.594 true 1.74,1.25 2.073,0.927 2.073,0.927 2.198,0.927 true 2.021,0.573 2.354,0.25 2.354,0.25 2.479,0.25 true 3.729,1.438 3.917,1.896 true 6.021,1.49 6.208,1.948 true 3.438,1.479 3.188,1.948 true 5.677,1.479 5.427,1.948 true 1.094,0.344 1.406,0.542 0.313,0.198 10 false *1 2.552,0.188 2.865,0.385 0.313,0.198 10 false 4 2.271,0.854 2.583,1.052 0.313,0.198 10 false 3 1.969,1.5 2.281,1.698 0.313,0.198 10 false 2 1.698,2.198 2.01,2.396 0.313,0.198 10 false 1 2.677,1.323 2.99,1.521 0.313,0.198 10 false C98 4.917,1.292 5.292,1.521 0.375,0.229 10 false C97 4.948,0.813 5.26,1.01 0.313,0.198 10 false *b 2.917,0.667 3.229,0.865 0.313,0.198 10 false *a 3.063,1.958 3.479,2.167 0.417,0.208 10 false GL1 3.823,1.948 4.323,2.177 0.5,0.229 10 false GL2 5.208,1.958 5.521,2.156 0.313,0.198 10 false GL3 6.188,1.969 6.5,2.167 0.313,0.198 10 false GL4
*1 No. 1 Glow Plug Connector - -
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)



b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C98-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always 10 kΩ or higher
C98-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always 10 kΩ or higher
C97-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always 10 kΩ or higher
C97-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.


Result:
Proceed to
OK
NG



OK

19.REPLACE GLOW PLUG CONTROLLER

NG

20.REPAIR OR REPLACE HARNESS OR CONNECTOR
19.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2GD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END