Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost
·

Radio and display receiver assembly

·

Map light assembly

·

Telephone microphone assembly

·

Harness or connector

·

Telematics transceiver*



*: w/ Telematics Transceiver


WIRING DIAGRAM

E353846E02
0.458,2.01 1.875,2.604 1.417,0.594 10 false Telephone Microphone Assembly 0.51,5.344 1.906,5.948 1.396,0.604 10 false Telephone Microphone Assembly 0.177,3.448 2.51,3.688 2.333,0.24 12 false w/o Telematics Transceiver: 0.115,0.125 2.448,0.365 2.333,0.24 12 false w/ Telematics Transceiver: 0.417,2.969 1.969,3.167 1.552,0.198 10 false Map Light Assembly 0.417,6.333 1.969,6.531 1.552,0.198 10 false Map Light Assembly 3.698,2.583 5.135,2.813 1.438,0.229 10 false Telematics Transceiver 5.417,2.667 7.104,3.125 1.688,0.458 10 false Radio and Display Receiver Assembly 5.375,6.167 7.083,6.583 1.708,0.417 10 false Radio and Display Receiver Assembly 2.323,6.385 3.229,6.594 0.906,0.208 10 false *: Shielded 0.406,6.156 0.719,6.354 0.313,0.198 10 false Q3 5.417,2.469 5.781,2.667 0.365,0.198 10 false G37 5.365,5.958 5.729,6.156 0.365,0.198 10 false G37 3.688,2.417 4.083,2.583 0.396,0.167 10 false G130 1.719,4.5 2.229,4.688 0.51,0.188 10 false MCO+ 1.729,4.885 2.24,5.073 0.51,0.188 10 false MCO- 1.688,4.083 2.198,4.271 0.51,0.188 10 false MACC 6,4.198 6.51,4.385 0.51,0.188 10 false MACC 6.01,4.625 6.448,4.802 0.438,0.177 10 false MIN+ 6.031,5 6.469,5.177 0.438,0.177 10 false MIN- 6.021,5.323 6.531,5.51 0.51,0.188 10 false SGND 5.979,1.625 6.49,1.813 0.51,0.188 10 false SGND 5.99,0.802 6.427,0.979 0.438,0.177 10 false MIN+ 5.99,1.177 6.427,1.354 0.438,0.177 10 false MIN- 1.729,0.656 2.24,0.844 0.51,0.188 10 false MACC 1.719,1.094 2.229,1.281 0.51,0.188 10 false MCO+ 1.76,1.479 2.271,1.667 0.51,0.188 10 false MCO- 3.875,0.771 4.385,0.958 0.51,0.188 10 false MCVD 4.333,0.771 4.844,0.958 0.51,0.188 10 false MCO+ 4.385,1.188 4.896,1.375 0.51,0.188 10 false MCO- 3.896,1.229 4.406,1.417 0.51,0.188 10 false MCI+ 3.885,1.594 4.396,1.781 0.51,0.188 10 false MCI- 3.875,2.031 4.385,2.219 0.51,0.188 10 false SGND 2.729,2.198 2.885,2.396 0.156,0.198 10 false * 3.344,2.229 3.5,2.427 0.156,0.198 10 false * 5.156,1.75 5.313,1.948 0.156,0.198 10 false * 3.229,5.5 3.385,5.698 0.156,0.198 10 false * 4.75,5.49 4.906,5.688 0.156,0.198 10 false * 5.5,1.781 5.656,1.979 0.156,0.198 10 false * 0.438,2.771 0.75,2.969 0.313,0.198 10 false Q3 2.26,0.615 2.51,0.813 0.25,0.198 10 false 15 2.281,1.083 2.531,1.281 0.25,0.198 10 false 14 5.74,0.656 5.896,0.854 0.156,0.198 10 false 5 2.292,1.51 2.542,1.708 0.25,0.198 10 false 13 2.271,4.094 2.521,4.292 0.25,0.198 10 false 15 2.271,4.5 2.521,4.698 0.25,0.198 10 false 14 2.271,4.906 2.521,5.104 0.25,0.198 10 false 13 3.583,0.667 3.833,0.865 0.25,0.198 10 false 33 3.583,1.052 3.833,1.25 0.25,0.198 10 false 34 3.583,1.5 3.833,1.698 0.25,0.198 10 false 35 3.583,1.917 3.833,2.115 0.25,0.198 10 false 32 4.833,0.635 5.083,0.833 0.25,0.198 10 false 18 4.833,1.052 5.083,1.25 0.25,0.198 10 false 19 5.677,1.073 5.927,1.271 0.25,0.198 10 false 19 5.667,1.5 5.917,1.698 0.25,0.198 10 false 18 5.75,4.469 5.906,4.667 0.156,0.198 10 false 5 5.76,4.083 5.917,4.281 0.156,0.198 10 false 4 5.667,4.885 5.917,5.083 0.25,0.198 10 false 19 5.667,5.219 5.917,5.417 0.25,0.198 10 false 18 0.99,0.75 1.5,0.938 0.51,0.188 10 false MACC 1,1.188 1.5,1.375 0.5,0.188 10 false MIC+ 1,1.625 1.51,1.813 0.51,0.188 10 false MIC- 1,4.198 1.51,4.385 0.51,0.188 10 false MACC 0.99,4.583 1.5,4.771 0.51,0.188 10 false MIC+ 1,4.979 1.51,5.167 0.51,0.188 10 false MIC- 1.531,0.635 1.781,0.833 0.25,0.198 10 false 5 1.521,1.063 1.771,1.26 0.25,0.198 10 false 3 1.531,1.51 1.781,1.708 0.25,0.198 10 false 2 1.531,4.083 1.781,4.281 0.25,0.198 10 false 5 1.531,4.5 1.781,4.698 0.25,0.198 10 false 3 1.521,4.927 1.771,5.125 0.25,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Model:
Model Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the Q3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-4 (MACC) - Q3-15 (MACC) Always Below 1 Ω
G37-5 (MIN+) - Q3-14 (MCO+) Always Below 1 Ω
G37-19 (MIN-) - Q3-13 (MCO-) Always Below 1 Ω
G37-18 (SGND) - Body ground Always 10 kΩ or higher
G37-4 (MACC) or Q3-15 (MACC) - Body ground Always 10 kΩ or higher
G37-5 (MIN+) or Q3-14 (MCO+) - Body ground Always 10 kΩ or higher
G37-19 (MIN-) or Q3-13 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the G130 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-5 (MIN+) - G130-18 (MCO+) Always Below 1 Ω
G37-19 (MIN-) - G130-19 (MCO-) Always Below 1 Ω
G37-5 (MIN+) or G130-18 (MCO+) - Body ground Always 10 kΩ or higher
G37-19 (MIN-) or G130-19 (MCO-) - Body ground Always 10 kΩ or higher
G37-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)
a.

Disconnect the G130 telematics transceiver connector.


b.

Disconnect the Q3 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-33 (MCVD) - Q3-15 (MACC) Always Below 1 Ω
G130-34 (MCI+) - Q3-14 (MCO+) Always Below 1 Ω
G130-35 (MCI-) - Q3-13 (MCO-) Always Below 1 Ω
G130-33 (MCVD) or Q3-15 (MACC) - Body ground Always 10 kΩ or higher
G130-34 (MCI+) or Q3-14 (MCO+) - Body ground Always 10 kΩ or higher
G130-35 (MCI-) or Q3-13 (MCO-) - Body ground Always 10 kΩ or higher
G130-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY

8.CHECK TELEMATICS TRANSCEIVER
a.
E283057C24
1.625,0.646 2.021,0.854 0.396,0.208 0.729,2.677 1.24,2.073 true 1.365,2.865 1.49,2.063 true 2.406,2.938 1.583,2.083 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.563,2.719 0.958,2.875 0.396,0.156 10 false MCI- 1.146,2.896 1.646,3.073 0.5,0.177 10 false MCVD 2.26,2.979 2.76,3.156 0.5,0.177 10 false SGND 1.646,0.667 2.146,0.844 0.5,0.177 10 false G130
*a Component with harness connected
(Telematics Transceiver)


Disconnect the Q3 map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G130-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-32 (SGND) - Body ground Always Below 1 Ω
G130-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

9.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY