Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

w/o Telematics Transceiver:

The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly.


w/ Telematics Transceiver:

The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the telematics transceiver sends power to the telephone microphone assembly, and the telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the telematics transceiver.


WIRING DIAGRAM

E353846E02
0.458,2.01 1.875,2.604 1.417,0.594 10 false Telephone Microphone Assembly 0.51,5.344 1.906,5.948 1.396,0.604 10 false Telephone Microphone Assembly 0.177,3.448 2.51,3.688 2.333,0.24 12 false w/o Telematics Transceiver: 0.115,0.125 2.448,0.365 2.333,0.24 12 false w/ Telematics Transceiver: 0.417,2.969 1.969,3.167 1.552,0.198 10 false Map Light Assembly 0.417,6.333 1.969,6.531 1.552,0.198 10 false Map Light Assembly 3.698,2.583 5.135,2.813 1.438,0.229 10 false Telematics Transceiver 5.417,2.667 7.104,3.125 1.688,0.458 10 false Radio and Display Receiver Assembly 5.375,6.167 7.083,6.583 1.708,0.417 10 false Radio and Display Receiver Assembly 2.323,6.385 3.229,6.594 0.906,0.208 10 false *: Shielded 0.406,6.156 0.719,6.354 0.313,0.198 10 false Q3 5.417,2.469 5.781,2.667 0.365,0.198 10 false G37 5.365,5.958 5.729,6.156 0.365,0.198 10 false G37 3.688,2.417 4.083,2.583 0.396,0.167 10 false G130 1.719,4.5 2.229,4.688 0.51,0.188 10 false MCO+ 1.729,4.885 2.24,5.073 0.51,0.188 10 false MCO- 1.688,4.083 2.198,4.271 0.51,0.188 10 false MACC 6,4.198 6.51,4.385 0.51,0.188 10 false MACC 6.01,4.625 6.448,4.802 0.438,0.177 10 false MIN+ 6.031,5 6.469,5.177 0.438,0.177 10 false MIN- 6.021,5.323 6.531,5.51 0.51,0.188 10 false SGND 5.979,1.625 6.49,1.813 0.51,0.188 10 false SGND 5.99,0.802 6.427,0.979 0.438,0.177 10 false MIN+ 5.99,1.177 6.427,1.354 0.438,0.177 10 false MIN- 1.729,0.656 2.24,0.844 0.51,0.188 10 false MACC 1.719,1.094 2.229,1.281 0.51,0.188 10 false MCO+ 1.76,1.479 2.271,1.667 0.51,0.188 10 false MCO- 3.875,0.771 4.385,0.958 0.51,0.188 10 false MCVD 4.333,0.771 4.844,0.958 0.51,0.188 10 false MCO+ 4.385,1.188 4.896,1.375 0.51,0.188 10 false MCO- 3.896,1.229 4.406,1.417 0.51,0.188 10 false MCI+ 3.885,1.594 4.396,1.781 0.51,0.188 10 false MCI- 3.875,2.031 4.385,2.219 0.51,0.188 10 false SGND 2.729,2.198 2.885,2.396 0.156,0.198 10 false * 3.344,2.229 3.5,2.427 0.156,0.198 10 false * 5.156,1.75 5.313,1.948 0.156,0.198 10 false * 3.229,5.5 3.385,5.698 0.156,0.198 10 false * 4.75,5.49 4.906,5.688 0.156,0.198 10 false * 5.5,1.781 5.656,1.979 0.156,0.198 10 false * 0.438,2.771 0.75,2.969 0.313,0.198 10 false Q3 2.26,0.615 2.51,0.813 0.25,0.198 10 false 15 2.281,1.083 2.531,1.281 0.25,0.198 10 false 14 5.74,0.656 5.896,0.854 0.156,0.198 10 false 5 2.292,1.51 2.542,1.708 0.25,0.198 10 false 13 2.271,4.094 2.521,4.292 0.25,0.198 10 false 15 2.271,4.5 2.521,4.698 0.25,0.198 10 false 14 2.271,4.906 2.521,5.104 0.25,0.198 10 false 13 3.583,0.667 3.833,0.865 0.25,0.198 10 false 33 3.583,1.052 3.833,1.25 0.25,0.198 10 false 34 3.583,1.5 3.833,1.698 0.25,0.198 10 false 35 3.583,1.917 3.833,2.115 0.25,0.198 10 false 32 4.833,0.635 5.083,0.833 0.25,0.198 10 false 18 4.833,1.052 5.083,1.25 0.25,0.198 10 false 19 5.677,1.073 5.927,1.271 0.25,0.198 10 false 19 5.667,1.5 5.917,1.698 0.25,0.198 10 false 18 5.75,4.469 5.906,4.667 0.156,0.198 10 false 5 5.76,4.083 5.917,4.281 0.156,0.198 10 false 4 5.667,4.885 5.917,5.083 0.25,0.198 10 false 19 5.667,5.219 5.917,5.417 0.25,0.198 10 false 18 0.99,0.75 1.5,0.938 0.51,0.188 10 false MACC 1,1.188 1.5,1.375 0.5,0.188 10 false MIC+ 1,1.625 1.51,1.813 0.51,0.188 10 false MIC- 1,4.198 1.51,4.385 0.51,0.188 10 false MACC 0.99,4.583 1.5,4.771 0.51,0.188 10 false MIC+ 1,4.979 1.51,5.167 0.51,0.188 10 false MIC- 1.531,0.635 1.781,0.833 0.25,0.198 10 false 5 1.521,1.063 1.771,1.26 0.25,0.198 10 false 3 1.531,1.51 1.781,1.708 0.25,0.198 10 false 2 1.531,4.083 1.781,4.281 0.25,0.198 10 false 5 1.531,4.5 1.781,4.698 0.25,0.198 10 false 3 1.521,4.927 1.771,5.125 0.25,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E309166

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check results are normal.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

2.CONFIRM MODEL
2.CONFIRM MODEL
a.

Choose the model to be inspected.

Model:
Model Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B




A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DIAPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the Q3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-4 (MACC) - Q3-15 (MACC) Always Below 1 Ω
G37-5 (MIN+) - Q3-14 (MCO+) Always Below 1 Ω
G37-19 (MIN-) - Q3-13 (MCO-) Always Below 1 Ω
G37-18 (SGND) - Body ground Always 10 kΩ or higher
G37-4 (MACC) or Q3-15 (MACC) - Body ground Always 10 kΩ or higher
G37-5 (MIN+) or Q3-14 (MCO+) - Body ground Always 10 kΩ or higher
G37-19 (MIN-) or Q3-13 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

5.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (RADIO AND DIAPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the G130 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-5 (MIN+) - G130-18 (MCO+) Always Below 1 Ω
G37-19 (MIN-) - G130-19 (MCO-) Always Below 1 Ω
G37-5 (MIN+) or G130-18 (MCO+) - Body ground Always 10 kΩ or higher
G37-19 (MIN-) or G130-19 (MCO-) - Body ground Always 10 kΩ or higher
G37-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY)
a.

Disconnect the G130 telematics transceiver connector.


b.

Disconnect the Q3 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-33 (MCVD) - Q3-15 (MACC) Always Below 1 Ω
G130-34 (MCI+) - Q3-14 (MCO+) Always Below 1 Ω
G130-35 (MCI-) - Q3-13 (MCO-) Always Below 1 Ω
G130-33 (MCVD) or Q3-15 (MACC) - Body ground Always 10 kΩ or higher
G130-34 (MCI+) or Q3-14 (MCO+) - Body ground Always 10 kΩ or higher
G130-35 (MCI-) or Q3-13 (MCO-) - Body ground Always 10 kΩ or higher
G130-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY

9.CHECK TELEMATICS TRANSCEIVER
a.
E283057C24
1.625,0.646 2.021,0.854 0.396,0.208 0.729,2.677 1.24,2.073 true 1.365,2.865 1.49,2.063 true 2.406,2.938 1.583,2.083 true 0.24,0.135 0.552,0.292 0.313,0.156 10 false *a 0.563,2.719 0.958,2.875 0.396,0.156 10 false MCI- 1.146,2.896 1.646,3.073 0.5,0.177 10 false MCVD 2.26,2.979 2.76,3.156 0.5,0.177 10 false SGND 1.646,0.667 2.146,0.844 0.5,0.177 10 false G130
*a Component with harness connected
(Telematics Transceiver)


Disconnect the Q3 map light assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G130-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-32 (SGND) - Body ground Always Below 1 Ω
G130-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

10.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one and check that the malfunction disappears.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY