Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › ENGINE UNIT › from 2016.08
RM3250E _51 Engine / Hybrid System _038006 2GD-FTV ENGINE MECHANICAL _0189239 ENGINE UNIT A

2GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 44763C 1.REMOVE NO. 2 HOSE TO HOSE TUBE

a.
A343494

Slide the clamp and disconnect the union to check valve hose from the vacuum pump assembly.


b.

Remove the 2 bolts and No. 2 hose to hose tube from the cylinder head cover sub-assembly and hose bracket.


Hide 12632 2.REMOVE NO. 2 ENGINE COVER BRACKET

Hide 82121 3.REMOVE ENGINE WIRE

Hide 26100G 5.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 6.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 16274 7.REMOVE WATER BY-PASS PLUG (w/o Heater)

a.
A343496

Slide the clamp and remove the water by-pass plug from the water outlet sub-assembly.


Hide 89481B 8.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 9.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 25733A 10.REMOVE NO. 1 VACUUM PIPE (w/ DPF)

Hide 12631A 13.REMOVE ENGINE COVER BRACKET

a.
A343495

Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


Hide 89421C 15.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 25625 16.REMOVE EGR VALVE BRACKET

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 16206B 19.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A368227

Disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.


b.
A368228

Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.


c.

Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the EGR valve adapter sub-assembly.


Hide 27148A 20.REMOVE CONNECTING WIRE

a.
A343587

Disconnect the connector from the common rail assembly.


b.

Detach the 2 clamps and remove the connecting wire from the hose bracket.


Hide 25601 21.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

a.
A343497

Remove the 4 nuts, bolt and No. 1 EGR pipe from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25804 22.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 16209 23.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

w/ DPF:

i.
A347295C01
0.833,0.229 1.021,0.229 1.021,0.229 1.708,0.76 true 2.25,0.208 2.448,0.208 2.448,0.208 2.677,0.5 true 2.958,0.833 2.74,0.833 2.74,0.833 2.74,1.167 true 0.708,2.073 0.906,2.073 0.906,2.073 1.333,1.635 true 2.302,2.646 2.5,2.646 2.5,2.646 2.729,2.938 true 2.125,2.135 2.302,2.135 2.302,2.135 2.635,1.865 true 2.958,3.271 2.74,3.271 2.74,3.271 2.74,3.604 true 2.188,4.49 2.365,4.49 2.365,4.49 2.698,4.219 true 0.927,2.729 1.115,2.729 1.115,2.729 1.792,3.25 true 0.073,0.052 0.438,0.375 0.365,0.323 12 true *A 0.073,2.51 0.396,2.802 0.323,0.292 12 true *B 1.948,2.042 2.135,2.229 0.188,0.188 10 true *1 0.656,0.135 0.875,0.344 0.219,0.208 10 false *2 2.063,0.104 2.271,0.292 0.208,0.188 10 true *3 0.531,1.969 0.781,2.177 0.25,0.208 10 false *4 2.99,0.74 3.24,0.948 0.25,0.208 10 true *5 2.01,4.396 2.208,4.594 0.198,0.198 10 true *1 2.104,2.552 2.302,2.75 0.198,0.198 10 true *3 0.75,2.635 0.969,2.844 0.219,0.208 10 false *2 2.979,3.177 3.198,3.354 0.219,0.177 10 true *5
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 11 Water By-pass Hose
*5 No. 17 Water By-pass Hose


Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


ii.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


iv.

Slide the clamp and disconnect the No. 17 water by-pass hose from the EGR pipe with cooler sub-assembly.


v.

for Cold Area Specification Vehicles:

Detach the clamp and disconnect the No. 11 water by-pass hose from the No. 2 fuel pipe.


vi.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.



b.

w/o DPF:

i.
A354082C01
0.969,0.24 1.177,0.24 1.177,0.24 1.74,0.781 true 0.781,2 0.99,2 0.99,2 1.396,1.583 true 3.031,2.063 2.802,2.063 2.802,2.063 2.802,1.781 true 2.167,0.125 2.354,0.125 2.354,0.125 2.698,0.458 true 2.188,2.594 2.375,2.594 2.375,2.594 2.635,3.021 true 1.042,3.333 1.74,3.333 true 3.052,3.667 2.823,3.667 2.823,3.667 2.823,4.167 true 0.104,0.063 0.469,0.313 0.365,0.25 12 false *A 0.104,2.49 0.5,2.74 0.396,0.25 12 false *B 3.073,3.573 3.333,3.792 0.26,0.219 10 true *1 0.802,0.135 1.042,0.333 0.24,0.198 10 true *2 1.969,0.031 2.177,0.229 0.208,0.198 10 true *3 0.625,1.906 0.938,2.063 0.313,0.156 10 false *4 3.063,1.979 3.313,2.198 0.25,0.219 10 true *1 2.01,2.5 2.271,2.719 0.26,0.219 10 true *3 0.865,3.24 1.104,3.438 0.24,0.198 10 true *2
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 11 Water By-pass Hose


Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


ii.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


iv.

for Cold Area Specification Vehicles:

Detach the clamp and disconnect the No. 11 water by-pass hose from the No. 2 fuel pipe.


v.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.



Hide 24.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

a.
A347296

Remove the 4 nuts, bolt and EGR pipe with cooler sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25800 25.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Cooler)

Hide 26.REMOVE EGR VALVE ADAPTER WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/o EGR Cooler)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A365517

Remove the 4 bolts and EGR valve adapter sub-assembly with electric EGR control valve assembly from the intake manifold.


Hide 11409 27.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23812D 28.REMOVE NO. 2 FUEL PIPE

a.
A343499

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


b.

Remove the bolt and No. 2 fuel pipe from the manifold stay.


Hide 29.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 31.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 32.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 33.REMOVE NO. 2 FUEL HOSE

Hide 23271H 34.REMOVE NO. 1 FUEL HOSE

Hide 23804D 35.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)

Hide 23815D 36.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 37.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 38.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 40.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 42.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 43.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A343500

Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.


Hide 23701 44.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 45.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 46.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 19850 47.REMOVE GLOW PLUG ASSEMBLY

Hide 44781 48.REMOVE HOSE BRACKET

a.
A343501

Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.


Hide 23300D 49.REMOVE DIESEL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)

a.
A347297

Remove the 2 nuts and diesel fuel filter assembly from the cylinder block sub-assembly.


Hide 23780 50.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)

a.
A343502

Remove the 2 nuts and No. 3 nozzle leakage pipe from the cylinder block sub-assembly.


Hide 16025 51.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343503

Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


Hide 88431 52.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

a.
A343504

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 16630D 53.REMOVE IDLER PULLEY ASSEMBLY (w/o Air Conditioning System)

a.
A347298

Remove the 3 bolts and idler pulley assembly from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 89422C 54.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 12229 55.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 16282 56.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.
A347299

Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.


b.

Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.


Hide 16281 57.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.
A347300

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


Hide 23295D 58.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 89467B 59.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)

Hide 12261 65.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 16268 67.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A347301C02
0.094,0.063 0.406,0.219 0.313,0.156 12 false *A 0.094,2.5 0.406,2.656 0.313,0.156 12 false *B
*A for Cold Area Specification Vehicles
*B except Cold Area Specification Vehicles


Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.


Hide 16284 68.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 69.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.
A347302

Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly from the cylinder block sub-assembly and timing chain cover sub-assembly.


Hide 15407 72.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 83530 75.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 16207 76.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343506

Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.


b.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


Hide 16304 77.REMOVE WATER OUTLET SUB-ASSEMBLY

a.
A347303C01
0.104,0.063 0.49,0.344 0.385,0.281 12 false *A 0.104,2.438 0.479,2.76 0.375,0.323 12 false *B
*A w/ DPF
*B w/o DPF


Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.


b.

Remove the gasket from the timing chain cover sub-assembly.


Hide 16321 78.REMOVE WATER INLET

a.
A343508

Remove the 3 bolts and water inlet from the timing chain cover sub-assembly.


Hide 16331A 79.REMOVE THERMOSTAT

Hide 16603 80.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 81.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 25706 82.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A365406C01
0.135,0.115 0.479,0.375 0.344,0.26 12 false *A 0.135,2.417 0.438,2.698 0.302,0.281 12 false *B
*A w/ EGR Cooler
*B w/o EGR Cooler


w/ EGR Cooler:

Disconnect the No. 1 vacuum transmitting hose from the vacuum pump assembly.


b.

Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.


Hide 29300 83.REMOVE VACUUM PUMP ASSEMBLY

a.
A343510

Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.


b.

Remove the 2 O-rings from the vacuum pump assembly.


Hide 11382C 84.REMOVE CAMSHAFT OIL SEAL RETAINER

a.
A343511

Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 88451B 85.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 88.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.
A347304

Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.