Home › Engine / Hybrid System › 2GD-FTV LUBRICATION › OIL PUMP › from 2016.08
RM3250E _51 Engine / Hybrid System _038011 2GD-FTV LUBRICATION _0187780 OIL PUMP A

2GD-FTV LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the timing chain case assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Memorize steering angle neutral point Pre-crash safety system (Click here)
Replacement of engine assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

(Click here)

·

w/ DPF:

(Click here)


Clear Crank Time Compensation Data Engine starting
·

(Click here)

·

w/ DPF:

(Click here)


Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

(Click here)

·

w/ DPF:

(Click here)


·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger sub-assembly

·

Replacement of turbocharger sub-assembly or turbocharger variable nozzle motor


Perform initialization -
·

(Click here)

·

w/ DPF:

(Click here)



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.



PROCEDURE

Hide 44763C 2.REMOVE NO. 2 HOSE TO HOSE TUBE

Hide 12632 3.REMOVE NO. 2 ENGINE COVER BRACKET

Hide 82121 4.REMOVE ENGINE WIRE

Hide 26100G 6.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 7.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 89481B 8.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 9.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 25733A 10.REMOVE NO. 1 VACUUM PIPE (w/ DPF)

Hide 12631A 13.REMOVE ENGINE COVER BRACKET

Hide 89421C 15.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 25625 16.REMOVE EGR VALVE BRACKET

Hide 16206B 18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 16206B 19.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 25601 21.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

Hide 25804 22.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 16209 23.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 24.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

Hide 25800 25.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Cooler)

Hide 25624 26.REMOVE EGR VALVE ADAPTER WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/o EGR Cooler)

Hide 11409 27.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 29.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 31.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 32.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 33.REMOVE NO. 2 FUEL HOSE

Hide 23271H 34.REMOVE NO. 1 FUEL HOSE

Hide 23804D 35.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)

Hide 23815D 36.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 37.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 38.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 40.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 42.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 43.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23701 44.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 88431 46.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 16630D 47.REMOVE IDLER PULLEY ASSEMBLY (w/o Air Conditioning System)

Hide 12229 48.REMOVE PCV PIPE (for Cold Area Specification Vehicles)

Hide 16282 49.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

Hide 16281 50.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

Hide 23295D 51.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 89467B 52.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)

Hide 12261 58.REMOVE PCV HOSE (except Cold Area Specification Vehicles)

Hide 16268 60.REMOVE NO. 1 WATER BY-PASS PIPE

Hide 16284 61.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 87101 62.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 15407 65.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 16207 67.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16304 68.REMOVE WATER OUTLET SUB-ASSEMBLY

Hide 16331A 70.REMOVE THERMOSTAT

Hide 16603 71.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A339577

Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.


Hide 16620 72.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A339579

Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


Hide 88451B 73.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16575C 76.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

Hide 12281A 77.REMOVE NO. 1 ENGINE HANGER

Hide 12501 78.REMOVE GENERATOR BRACKET SUB-ASSEMBLY

Hide 23670 79.REMOVE INJECTOR ASSEMBLY

Hide 23682 80.REMOVE NOZZLE HOLDER GASKET

Hide 11301M 81.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 82.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A339580C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.


b.
A339581C01
2.219,0.563 2.427,0.292 2.427,0.292 2.552,0.292 true 0.323,1.802 0.469,1.802 0.469,1.802 0.708,1.25 true 0.885,1.385 1.063,1.26 1.063,1.26 1.188,1.26 true 0.771,0.594 1.031,0.365 1.031,0.365 1.156,0.365 true 2.615,0.198 2.813,0.385 0.198,0.188 10 true *1 0.115,1.719 0.292,1.885 0.177,0.167 10 false *2 1.229,1.167 1.417,1.333 0.188,0.167 10 true *3 1.229,0.281 1.417,0.448 0.188,0.167 10 false *3
*1 Cylinder Head Cover Gasket
*2 No. 2 Cylinder Head Cover Gasket
*3 Camshaft Bearing Cap Oil Hole Gasket


Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.


Hide 12144 83.REMOVE OIL PAN COVER SILENCER

a.
A339601

Remove the 5 bolts and oil pan cover silencer from the oil pan sub-assembly.


Hide 89491 84.REMOVE ENGINE OIL LEVEL SENSOR

Hide 12101 85.REMOVE OIL PAN SUB-ASSEMBLY

a.
A339600C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 23 bolts and 2 nuts.


b.
A303108

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

·

Be careful not to damage the cylinder block sub-assembly flange.




Hide 16100 86.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 87.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11324 88.REMOVE TIMING CHAIN COVER PLATE

Hide 22100 89.REMOVE SUPPLY PUMP ASSEMBLY

Hide 22815A 90.REMOVE INJECTION PUMP INSULATOR

Hide 11302 91.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A339584

Remove the 20 bolts from the timing chain cover sub-assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.

A339585C01
6.156,0.719 6.49,0.177 6.49,0.177 6.625,0.177 true 5.604,1.927 6.094,2.396 6.094,2.396 6.229,2.396 true 0.406,1.156 0.552,1.156 0.552,1.156 1.052,0.708 true 0.198,1.073 0.385,1.25 0.188,0.177 10 false *a 6.302,2.313 6.51,2.479 0.208,0.167 10 false *a 6.677,0.083 6.885,0.26 0.208,0.177 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.



c.
A339592

Remove the timing chain case gasket from the timing chain case assembly.


Hide 11303A 92.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A339586C01
0.583,1.271 1.271,1.271 true 1.417,0.917 2.167,0.354 2.167,0.354 2.375,0.354 true 2.448,0.271 2.656,0.458 0.208,0.188 10 false *a 0.354,1.188 0.563,1.375 0.208,0.188 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver and wooden block, pull out the front crankshaft oil seal.

NOTICE:

Do not damage the surface of the front crankshaft oil seal press fit hole.



Hide 93.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

a.
A339596

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.3 mm (0.000787 to 0.0118 in.)


Maximum gear backlash:

0.42 mm (0.0165 in.)


If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.


Hide 13519 94.REMOVE OIL PUMP DRIVE GEAR

a.
A339595

Remove the oil pump drive gear from the crankshaft.


Hide 13566B 95.REMOVE TIMING CHAIN GUIDE

Hide 13550 96.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13559 97.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

Hide 13562 98.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13507 99.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 13540 100.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 101.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

Hide 13561 102.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 103.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13523 104.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11310 105.REMOVE TIMING CHAIN CASE ASSEMBLY

a.
A339590

Remove the 15 bolts from the timing chain case assembly.


b.

Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.

A339591C01
0.729,0.646 0.865,0.646 0.865,0.646 1.167,1.24 true 5.823,2.094 6.323,2.479 6.323,2.479 6.469,2.479 true 6.323,0.552 6.656,1.219 6.656,1.219 6.802,1.219 true 0.479,0.552 0.698,0.74 0.219,0.188 10 false *a 6.521,2.385 6.74,2.573 0.219,0.188 10 false *a 6.854,1.125 7.052,1.292 0.198,0.167 10 false *a
*a Protective Tape - -


NOTICE:

Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.



c.
A339593

Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.