Home › Engine / Hybrid System › 2GD-FTV ENGINE MECHANICAL › ENGINE UNIT
RM33J0E _51 Engine / Hybrid System _038438 2GD-FTV ENGINE MECHANICAL _0196036 ENGINE UNIT A

2GD-FTV ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 44763C 1.REMOVE NO. 2 HOSE TO HOSE TUBE

a.
A343494

Slide the clamp and disconnect the union to check valve hose from the vacuum pump assembly.


b.

Remove the 2 bolts and No. 2 hose to hose tube from the cylinder head cover sub-assembly and hose bracket.


Hide 12632 2.REMOVE NO. 2 ENGINE COVER BRACKET

Hide 82121 3.REMOVE ENGINE WIRE

Hide 26100G 5.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 6.REMOVE NO. 2 WATER BY-PASS PIPE

Hide 89481B 7.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 89425 8.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 12631A 12.REMOVE ENGINE COVER BRACKET

a.
A343495

Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.


Hide 89421C 14.REMOVE DIESEL TURBO PRESSURE SENSOR

Hide 25625 15.REMOVE EGR VALVE BRACKET

Hide 16206B 17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 27148A 18.REMOVE CONNECTING WIRE

a.
A343587

Disconnect the connector from the common rail assembly.


b.

Detach the 2 clamps and remove the connecting wire from the hose bracket.


Hide 25601 19.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

a.
A343497

Remove the 4 nuts, bolt and No. 1 EGR pipe sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25804 20.REMOVE VACUUM CONTROL VALVE SET

Hide 16209 21.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

w/ DPF:

i.
A365367C01
1.792,2 2.052,2 2.052,2 2.688,1.719 true 0.635,0.427 0.896,0.427 0.896,0.427 1.802,0.76 true 2.229,0.156 2.49,0.156 2.49,0.156 2.667,0.49 true 3.188,1.781 3.188,1.604 3.188,1.604 3,1.135 true 1.615,1.896 1.865,2.104 0.25,0.208 10 true *1 0.458,0.323 0.771,0.479 0.313,0.156 10 false *2 2.052,0.052 2.26,0.26 0.208,0.208 10 true *3 3.104,1.802 3.344,2.01 0.24,0.208 10 true *4
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose
*4 No. 17 Water By-pass Hose


Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


ii.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


iv.

Slide the clamp and disconnect the No. 17 water by-pass hose from the EGR pipe with cooler sub-assembly.


v.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.



b.

w/o DPF:

i.
A365368C01
2.833,1.656 2.833,1.135 2.833,1.135 3.063,1.135 true 0.938,0.813 1.719,0.813 true 2.656,0.552 2.542,0.146 2.542,0.146 2.333,0.146 true 3.073,1.042 3.354,1.271 0.281,0.229 10 true *1 0.76,0.719 1.042,0.979 0.281,0.26 10 true *2 2.156,0.052 2.375,0.25 0.219,0.198 10 true *3
*1 No. 6 Water By-pass Hose
*2 No. 7 Water By-pass Hose
*3 Water Hose


Slide the clamp and disconnect the No. 6 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


ii.

Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 4 water by-pass pipe sub-assembly.


iii.

Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.


iv.

Remove the 2 bolts and No. 4 water by-pass pipe sub-assembly from the intake manifold.



Hide 22.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

a.
A347296

Remove the 4 nuts, bolt and EGR pipe with cooler sub-assembly from the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.


b.

Remove the 2 gaskets from the exhaust manifold and electric EGR control valve assembly.


c.
A352178

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.


Hide 25800 23.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 11409 24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23812D 25.REMOVE NO. 2 FUEL PIPE

a.
A343499

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


b.

Remove the bolt and No. 2 fuel pipe from the manifold stay.


Hide 26.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 22803 28.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 23243B 29.REMOVE FUEL PUMP MOTOR WIRE

Hide 23273H 30.REMOVE NO. 2 FUEL HOSE

Hide 23271H 31.REMOVE NO. 1 FUEL HOSE

Hide 23804D 32.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)

Hide 23815D 33.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804C 34.REMOVE FUEL INLET PIPE SUB-ASSEMBLY

Hide 23770 35.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 37.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 23760 39.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 40.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A343500

Remove the 2 bolts and 2 wiring harness clamp brackets from the cylinder head cover sub-assembly.


Hide 23701 41.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23810A 42.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 43.REMOVE NO. 1 GLOW PLUG CONNECTOR

Hide 19850 44.REMOVE GLOW PLUG ASSEMBLY

Hide 44781 45.REMOVE HOSE BRACKET

a.
A343501

Remove the 2 bolts and hose bracket from the cylinder head sub-assembly.


Hide 23300 46.REMOVE FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)

a.
A347297

Remove the 2 nuts and fuel filter assembly from the cylinder block sub-assembly.


Hide 23780 47.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)

a.
A343502

Remove the 2 nuts and No. 3 nozzle leakage pipe from the cylinder block sub-assembly.


Hide 16025 48.REMOVE NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343503

Remove the 3 bolts, No. 5 water by-pass pipe sub-assembly and gasket from the cylinder block sub-assembly.


Hide 88431 49.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A343504

Remove the 4 bolts and No. 1 compressor mounting bracket from the cylinder block sub-assembly, timing chain case assembly and timing chain cover sub-assembly.


Hide 89422C 50.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 16282 51.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.
A347299

Slide the 2 clamps and disconnect the No. 5 water by-pass hose from the No. 1 injector holder and water outlet sub-assembly.


b.

Detach the clamp and remove the No. 5 water by-pass hose from the No. 1 water hose clamp bracket.


Hide 16281 52.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.
A347300

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 injector holder.


Hide 23295D 53.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 89467B 54.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)

Hide 16268 62.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A343505

Remove the 3 bolts, No. 1 water by-pass pipe and gasket from the timing chain cover sub-assembly.


Hide 16284 63.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 15407 66.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 83530 69.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 16207 70.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A343506

Slide the clamp and disconnect the No. 3 water by-pass hose from the water outlet sub-assembly.


b.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly from the engine water pump assembly and water inlet.


Hide 16304 71.REMOVE WATER OUTLET SUB-ASSEMBLY

a.
A347303C01
0.104,0.063 0.49,0.344 0.385,0.281 12 false *A 0.104,2.438 0.479,2.76 0.375,0.323 12 false *B
*A w/ DPF
*B w/o DPF


Remove the 4 bolts, 2 nuts and water outlet sub-assembly from the timing chain cover sub-assembly.


b.

Remove the gasket from the timing chain cover sub-assembly.


Hide 16321 72.REMOVE WATER INLET

a.
A343508

Remove the 3 bolts and water inlet from the timing chain cover sub-assembly.


Hide 16331A 73.REMOVE THERMOSTAT

Hide 16603 74.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 75.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 25706 76.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.
A343509

Disconnect the No. 1 vacuum transmitting hose from the vacuum pump assembly.


b.

Remove the 3 bolts and No. 1 vacuum transmitting pipe sub-assembly from the cylinder head sub-assembly.


Hide 29300 77.REMOVE VACUUM PUMP ASSEMBLY

a.
A343510

Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.


b.

Remove the 2 O-rings from the vacuum pump assembly.


Hide 11382C 78.REMOVE CAMSHAFT OIL SEAL RETAINER

a.
A343511

Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 16575C 81.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.
A347304

Remove the bolt and No. 1 water hose clamp bracket from the timing chain case assembly.