The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed signal*. The vehicle speed signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.
*: This vehicle speed signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.
When replacing the combination meter assembly, make sure to replace it with a new one.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
w/ Smart Entry and Start System:
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system.
If the body ECU has been replaced, it is necessary to initializa the body ECU.
For vehicles without a entry and start system, go to "Check Body ECU".
*1: for 2TR-FE
*2: for 1GD-FTV, 2GD-FTV
*3: for 1KD-FTV, 2KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Body ECU
*6: w/ Audio and Visual System (for Radio and Display Type)
*7: w/ Audio and Visual System (for Radio Receiver Type)
*8: w/ Navigation System
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G27 body ECU connector.*5
Disconnect the G37 radio and display receiver assembly connector.*6
Disconnect the G113 radio receiver assembly connector.*7
Disconnect the G116 navigation receiver assembly connector.*8
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a body ECU, go to "Check TCM".
*1: for 2TR-FE
*2: for 1GD-FTV, 2GD-FTV
*3: for 1KD-FTV, 2KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Audio and Visual System (for Radio and Display Type)
*7: w/ Audio and Visual System (for Radio Receiver Type)
*8: w/ Navigation System
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G37 radio and display receiver assembly connector.*6
Disconnect the G113 radio receiver assembly connector.*7
Disconnect the G116 navigation receiver assembly connector.*8
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a 1KD-FTV series engine, automatic transmission, go to "Check Radio and Display Receiver Assembly".
*1: w/ Smart Entry and Start System
*2: w/ Body ECU
*3: w/ Audio and Visual System (for Radio and Display Type)
*4: w/ Audio and Visual System (for Radio Receiver Type)
*5: w/ Navigation System
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G83 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1
Disconnect the G27 body ECU connector.*2
Disconnect the G37 radio and display receiver assembly connector.*3
Disconnect the G113 radio receiver assembly connector.*4
Disconnect the G116 navigation receiver assembly connector.*5
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without a navigation system, go to "Check Radio and Display Receiver Assembly".
*1: for 2TR-FE
*2: for 1GD-FTV
*3: for 1KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Body ECU
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without an audio and visual system (for radio and display type), go to "Check Radio Receiver Assembly".
*1: for 2TR-FE
*2: for 1GD-FTV
*3: for 1KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Body ECU
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
For vehicles without an audio and visual system (for radio receiver type), go to "Check ECM".
*1: for 2TR-FE
*2: for 1GD-FTV, 2GD-FTV
*3: for 1KD-FTV, 2KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Body ECU
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: w/ Smart Entry and Start System
*2: w/ Body ECU
*3: w/ Audio and Visual System (for Radio and Display Type)
*4: w/ Audio and Visual System (for Radio Receiver Type)
*5: for 1KD-FTV, Automatic Transmission
*6: w/ Navigation System
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1
Disconnect the G27 body ECU connector.*2
Disconnect the G37 radio and display receiver assembly connector.*3
Disconnect the G113 radio receiver assembly connector.*4
Disconnect the G90 TCM connector.*5
Disconnect the G116 navigation receiver assembly connector.*6
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | w/ VSC |
| *B | w/o VSC |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A4-14 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A3-22 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
| *b | Waveform |
Remove the combination meter assembly with the connector(s) still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Connect an oscilloscope to terminal G9-18 (SI) and body ground.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | G9-18 (SI) - Body ground |
| Tool Setting | 5 V/DIV, 20 ms./DIV |
| Vehicle Condition | Driving at approximately 20 km/h (12 mph) |
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/ VSC)>REMOVAL
w/o VSC: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL
*1: for 2TR-FE
*2: for 1GD-FTV, 2GD-FTV
*3: for 1KD-FTV, 2KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Body ECU
*6: w/ Audio and Visual System (for Radio and Display Type)
*7: w/ Audio and Visual System (for Radio Receiver Type)
*8: w/ Navigation System
Disconnect the G9 combination meter assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.
Disconnect the G90 TCM connector.*4
Disconnect the G27 body ECU connector.*5
Disconnect the G37 radio and display receiver assembly connector.*6
Disconnect the G113 radio receiver assembly connector.*7
Disconnect the G116 navigation receiver assembly connector.*8
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G69-7 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G69-7 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 2TR-FE
*2: for 1GD-FTV, 2GD-FTV
*3: for 1KD-FTV, 2KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Audio and Visual System (for Radio and Display Type)
*7: w/ Audio and Visual System (for Radio Receiver Type)
*8: w/ Navigation System
Disconnect the G9 combination meter assembly connector.
Disconnect the G27 body ECU connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G37 radio and display receiver assembly connector.*6
Disconnect the G113 radio receiver assembly connector.*7
Disconnect the G116 navigation receiver assembly connector.*8
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G27-5 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G27-5 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
*1: w/ Smart Entry and Start System
*2: w/ Speed-sensitive Automatic Door Lock Function
*3: w/ Audio and Visual System (for Radio and Display Type)
*4: w/ Audio and Visual System (for Radio Receiver Type)
*5: w/ Navigation System
Disconnect the G9 combination meter assembly connector.
Disconnect the G90 TCM connector.
Disconnect the G83 ECM connector.
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1
Disconnect the G27 body ECU connector.*2
Disconnect the G37 radio and display receiver assembly connector.*3
Disconnect the G113 radio receiver assembly connector.*4
Disconnect the G116 navigation receiver assembly connector.*5
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G90-25 (SPD1) | Always | Below 1 Ω |
| G9-19 (+S) or G90-25 (SPD1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 2TR-FE
*2: for 1GD-FTV
*3: for 1KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Body ECU
Disconnect the G9 combination meter assembly connector.
Disconnect the G116 navigation receiver assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G116-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G116-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 2TR-FE
*2: for 1GD-FTV
*3: for 1KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Body ECU
Disconnect the G9 combination meter assembly connector.
Disconnect the G37 radio and display receiver assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G37-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G37-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 2TR-FE
*2: for 1GD-FTV, 2GD-FTV
*3: for 1KD-FTV, 2KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Body ECU
Disconnect the G9 combination meter assembly connector.
Disconnect the G113 radio receiver assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G113-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G113-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 2TR-FE
*2: for 1GD-FTV, 2GD-FTV
*3: for 1KD-FTV, 2KD-FTV
*4: for 1KD-FTV, Automatic Transmission
*5: w/ Smart Entry and Start System
*6: w/ Body ECU
*7: w/ Audio and Visual System (for Radio and Display Type)
*8: w/ Audio and Visual System (for Radio Receiver Type)
*9: w/ Navigation System
Disconnect the G9 combination meter assembly connector.
Disconnect the G45*1, G85*2 or G83*3 ECM connector.
Disconnect the G90 TCM connector.*4
Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5
Disconnect the G27 body ECU connector.*6
Disconnect the G37 radio and display receiver assembly connector.*7
Disconnect the G117 radio receiver assembly connector.*8
Disconnect the G116 navigation receiver assembly connector.*9
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G45-23 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G45-23 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G85-10 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G85-10 (SPD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-19 (+S) - G83-17 (SPD) | Always | Below 1 Ω |
| G9-19 (+S) or G83-17 (SPD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
NG
Disconnect the G9 combination meter assembly connector.
Disconnect the A4*1 or A3*2 brake actuator assembly (skid control ECU) connector.
*1: w/ VSC
*2: w/o VSC
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-18 (SI) - A4-14 (SP1) | Always | Below 1 Ω |
| G9-18 (SI) or A4-14 (SP1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-18 (SI) - A3-22 (SP1) | Always | Below 1 Ω |
| G9-18 (SI) or A3-22 (SP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG