Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE UNIT › from 2016.07
RM33J0E _51 Engine / Hybrid System _053774 2TR-FBE ENGINE MECHANICAL _0261409 ENGINE UNIT A

2TR-FBE ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of throttle with motor body assembly

·

Cleaning the deposits from the throttle with motor body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of knock sensor


Inspection after repair Poor idle, engine start, etc. (Click here)

PROCEDURE

Hide 22030 1.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 23270 2.REMOVE FUEL PRESSURE PULSATION DAMPER ASSEMBLY

Hide 23250 3.REMOVE FUEL DELIVERY PIPE WITH FUEL INJECTOR

Hide 23250 4.REMOVE FUEL INJECTOR ASSEMBLY

Hide 12229 6.REMOVE PCV PIPE

a.
A382737

Disconnect the PCV hose from the PCV valve sub-assembly and intake manifold.


b.

Remove the bolt and PCV pipe.


Hide 8.REMOVE ENGINE WIRE

a.

Disconnect the connectors and clamps of the engine wire connected to the engine assembly.


b.
A348631

Remove the 3 bolts and engine wire from the engine assembly.


Hide 9.REMOVE HEATER HOSE

a.
A382738

Slide the 2 clamp and remove the heater hose from the cylinder head sub-assembly and No. 1 water by-pass pipe.


Hide 16261G 10.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A382739

Slide the clamp and remove the No. 1 water by-pass hose from the cylinder head sub-assembly.


Hide 12315 11.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A359080

Remove the 4 bolts and front No. 1 engine mounting bracket LH.


Hide 12311 12.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A359081

Remove the 4 bolts and front No. 1 engine mounting bracket RH.


Hide 17167 13.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25710 15.REMOVE AIR SWITCHING VALVE ASSEMBLY

Hide 27020 18.REMOVE GENERATOR ASSEMBLY

Hide 88440B 19.REMOVE IDLE PULLEY ASSEMBLY

a.
A346825

Loosen the bolt and then remove the idle pulley assembly.

HINT:

The bolt in the illustration cannot be removed from the idle pulley assembly.



Hide 88431 20.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A346826

Remove the 5 bolts and No. 1 compressor mounting bracket.


Hide 16603 21.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16268 22.REMOVE NO. 1 WATER BY-PASS PIPE

a.

Slide the clamp and disconnect the No. 4 water by-pass hose from the No. 1 water by-pass pipe.


b.
A382740

Remove the 2 nuts, No. 1 water by-pass pipe and gasket.