Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE › 2015.08–2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0195330 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43212 1.INSTALL STEERING KNUCKLE LH

C328308C01
2.875,1.271 3.188,1.469 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


a.

Apply MP grease to a new O-ring.


b.

Install the O-ring to the front axle hub sub-assembly LH.


c.

Install the dust cover and front axle hub sub-assembly LH to the steering knuckle LH with the 4 bolts.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a ball joint lock nut wrench (fulcrum length of 149 mm (5.866 in.)) + torque wrench (fulcrum length of 380 mm (14.961 in.)): 57.5 N*m (586 kgf*cm, 42 ft.*lbf).




Hide 43502K 2.INSTALL FRONT AXLE HUB DUST SEAL

C325055N01
0.823,2.073 0.479,1.615 0.479,1.615 0.969,1.875 false 0.771,2.333 0.5,1.646 true 0.177,1.469 0.635,1.667 0.458,0.198 10 false SST

a.

Using SST and a press, press in a new front axle hub dust seal.

SST
09527-17011  
09950-70010  (09951-07100)
09951-01000  


Hide 48630 3.CONNECT FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.

Install the front upper suspension arm assembly LH to the steering knuckle LH with a nut.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


b.

Install a new clip.

NOTICE:

If the holes for the clip are not aligned, tighten the nut an additional 60°.



Hide 48069 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM ASSEMBLY LH

a.

Connect the front lower No. 1 suspension arm assembly LH to the steering knuckle LH with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 5.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 48810 6.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the steering knuckle LH with the nut.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.



Hide 43502H 7.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43514C 8.INSTALL FRONT AXLE HUB GREASE CAP

Hide 43512 9.INSTALL FRONT DISC

Hide 47750 10.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY LH

Hide 89543 11.CONNECT FRONT SPEED SENSOR LH

a.
C322645

Install the skid control sensor clamp to the steering knuckle with the bolt.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


b.

Install the speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

·

While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

When installing the sensor, do not twist the wire harness.




c.
C322643

Install the harness clamp with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:
·

When installing the clamp, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




d.

Attach the clamp.


Hide 12.INSTALL FRONT WHEEL

Hide 13.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 15.PERFORM INITIALIZATION (w/ Automatic Headlight Beam Level Control System)

Hide 16.INSPECT AUTOMATIC LIGHT CONTROL SYSTEM (w/ Automatic Headlight Beam Level Control System)

Hide 17.INSPECT HEADLIGHT AIMING (w/ Automatic Headlight Beam Level Control System)