Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2015.08–2016.01
RM3270E _56 Audio / Visual / Telematics _041700 NAVIGATION / MULTI INFO DISPLAY _0197741 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and also the navigation receiver assembly itself cannot function.

WIRING DIAGRAM

E317101E04
0.49,0.969 0.948,1.167 0.458,0.198 10 false VOL- 1.313,0.969 1.771,1.167 0.458,0.198 10 false VOL+ 1.938,0.969 2.396,1.167 0.458,0.198 10 false SEEK- 2.583,0.979 3.042,1.135 0.458,0.156 10 false SEEK+ 0.427,2.125 0.927,2.323 0.5,0.198 10 false VOICE 1.188,2.021 1.688,2.365 0.5,0.344 10 false OFF HOOK 1.865,2 2.365,2.344 0.5,0.344 10 false ON HOOK 2.542,2.125 3.042,2.469 0.5,0.344 10 false MODE 1.552,3.104 3.729,3.333 2.177,0.229 10 false Steering Pad Switch LH Side 1.281,3.604 3.635,3.833 2.354,0.229 10 false Steering Pad Switch Assembly 4.49,0.25 4.729,0.427 0.24,0.177 10 false 11 4.542,1.354 4.781,1.531 0.24,0.177 10 false 8 4.51,2.458 4.75,2.635 0.24,0.177 10 false 10 5.417,0.24 5.656,0.417 0.24,0.177 10 false 6 5.427,1.354 5.667,1.531 0.24,0.177 10 false 3 5.417,2.469 5.656,2.646 0.24,0.177 10 false 5 4.5,0.438 4.74,0.615 0.24,0.177 10 false z2 4.51,1.552 4.75,1.729 0.24,0.177 10 false z2 4.51,2.656 4.75,2.833 0.24,0.177 10 false z2 5.354,0.448 5.594,0.625 0.24,0.177 10 false G4 5.333,1.552 5.573,1.729 0.24,0.177 10 false G4 5.354,2.667 5.594,2.844 0.24,0.177 10 false G4 5.938,0.354 6.292,0.521 0.354,0.167 10 false 21 5.948,1.458 6.302,1.625 0.354,0.167 10 false 23 5.927,2.563 6.281,2.729 0.354,0.167 10 false 22 6.198,0.458 6.781,0.625 0.583,0.167 10 false SW1 6.219,1.573 6.802,1.74 0.583,0.167 10 false SWG 6.229,2.708 6.813,2.875 0.583,0.167 10 false SW2 5.823,4.698 6.375,4.865 0.552,0.167 10 false G41 5.833,4.865 7.052,5.188 1.219,0.323 10 false Navigation Receiver Assembly 4.875,0.323 5.24,0.5 0.365,0.177 10 false AU1 4.875,1.438 5.24,1.615 0.365,0.177 10 false EAU 4.885,2.552 5.25,2.729 0.365,0.177 10 false AU2 4.208,3.625 5.75,3.979 1.542,0.354 10 false Spiral with Sensor Cable Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)
a.

Disconnect the G41 navigation receiver assembly connector.


b.

Disconnect the G4 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G41-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
G41-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G41-21 (SW1) - Body ground Always 10 kΩ or higher
G41-23 (SWG) - Body ground Always 10 kΩ or higher
G41-22 (SW2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR