Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR
RM3270E _58 Vehicle Interior _041710 SUPPLEMENTAL RESTRAINT SYSTEMS _0199698 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the side airbag sensor assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR NO. 2 SEAT ASSEMBLY RH

Hide 67917C 4.REMOVE REAR DOOR SCUFF PLATE RH

Hide 67935 5.REMOVE BACK DOOR SCUFF PLATE

Hide 73233A 6.REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

Hide 73233B 7.REMOVE REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER

Hide 62511 8.REMOVE QUARTER INSIDE TRIM BOARD RH

Hide 89860 9.REMOVE SIDE AIRBAG SENSOR ASSEMBLY RH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) terminal of the battery, the airbag may deploy even if an impact is applied only to the side airbag sensor assembly RH. Therefore, make sure that the negative (-) terminal of the battery is disconnected before performing this procedure.




c.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)


ii.

Push the housing lock again and disconnect the airbag connector.

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.


C195226C32
3.927,1.313 3.927,2.146 false 1.385,1.313 1.385,2.146 true 0.948,1.156 0.417,0.729 true 3.469,1.146 2.938,0.74 true 1.125,0.99 0.865,0.552 true 3.635,1.01 3.375,0.573 true 0.698,0.448 0.885,0.625 0.188,0.177 10 false *a 3.208,0.479 3.396,0.656 0.188,0.177 10 false *a 1.333,2.188 1.521,2.365 0.188,0.177 10 false *b 0.25,0.635 0.438,0.813 0.188,0.177 10 false *c 3.823,2.177 4.01,2.354 0.188,0.177 10 false *b 2.771,0.635 3.021,0.823 0.25,0.188 10 false *c
*a Housing Lock *b CPA
*c CPA Upper Part - -




d.
B409208

Remove the bolt.

NOTICE:

Loosen the bolt while holding the side airbag sensor assembly RH because the side airbag sensor assembly RH guide is easily damaged.



e.

Detach the guide and remove the side airbag sensor assembly RH.