| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1507 | Open in Turn Signal Circuit | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
Open in turn signal light circuit. |
·
Harness or connector ·
Headlight assembly ·
Side turn signal light assembly ·
Outer rear view mirror assembly ·
Rear combination light assembly ·
Combination meter assembly |
| B1508 | Short in Turn Signal / Hazard Flasher Circuit | Both conditions are met:
·
IG voltage is 10.5 V or higher. ·
Short in turn signal light circuit or hazard warning light circuit. |
·
Harness or connector ·
Headlight assembly ·
Side turn signal light assembly ·
Outer rear view mirror assembly ·
Rear combination light assembly ·
Combination meter assembly |
When replacing the combination meter assembly, make sure to replace it with a new one.
Inspect the bulbs for circuits related to this system before performing the following inspection procedure.
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
B1507 and B1508 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| LH side turn signal light does not illuminate. | A |
| RH side turn signal light does not illuminate. | B |
A
B
Disconnect the G10 combination meter assembly connector.
Disconnect the A63 headlight assembly LH connector.
Disconnect the K3 outer rear view mirror assembly LH connector.
Disconnect the N33 rear combination light assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G10-8 (LL) - A63-2 (B) | Always | Below 1 Ω |
| G10-8 (LL) - K3-10 (TRNL) | Always | Below 1 Ω |
| G10-8 (LL) - N33-3 (B) | Always | Below 1 Ω |
| A63-1 (E) - Body ground | Always | Below 1 Ω |
| K3-6 (GND) - Body ground | Always | Below 1 Ω |
| N33-5 (E) - Body ground | Always | Below 1 Ω |
| G10-8 (LL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the headlight unit assembly LH.
for LED Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL
for Halogen Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>REMOVAL
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
B1507 and B1508 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
B1507 and B1508 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G10 combination meter assembly connector.
Disconnect the A62 headlight assembly RH connector.
Disconnect the J2 outer rear view mirror assembly RH connector.
Disconnect the N32 rear combination light assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G10-13 (LR) - A62-2 (B) | Always | Below 1 Ω |
| G10-13 (LR) - J2-10 (TRNR) | Always | Below 1 Ω |
| G10-13 (LR) - N32-3 (B) | Always | Below 1 Ω |
| A62-1 (E) - Body ground | Always | Below 1 Ω |
| J2-6 (GND) - Body ground | Always | Below 1 Ω |
| N32-5 (E) - Body ground | Always | Below 1 Ω |
| G10-13 (LR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly RH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the headlight unit assembly RH.
for LED Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL
for Halogen Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>REMOVAL
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
B1507 and B1508 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Clear the DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
B1507 and B1508 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG