The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door disassembly/reassembly are shown below.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the RH side.
Fully open the rear door glass sub-assembly RH before proceeding with work.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67673A
3.REMOVE REAR DOOR FRAME GARNISH RH
Detach the clip and claw and remove the rear door frame garnish RH.
74250
4.REMOVE REAR ARMREST ASSEMBLY RH
|
Order of Removal |
|
Remove in this Direction |
Detach the clip and claw and remove the rear armrest assembly RH.
5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
|
Remove in this Direction |
Detach the clip and claw.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
84810D
6.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
81230
7.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
67665D
8.REMOVE REAR DOOR TRIM REFLECTOR RH (w/ Reflex Reflector Assembly)
| *A | for RH side |
| *B | for LH side |
|
Protective Tape |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Put protective tape around the reflex reflector.
Using a thin-bladed screwdriver, detach the claw and guide.
Tape the thin-bladed screwdriver tip before use.
Remove the rear door trim reflector RH.
69283A
9.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG RH
Using moulding remover A, detach the claw and remove the rear door inside handle bezel plug RH as shown in the illustration.
67603
10.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY RH
Remove the 3 screws.
|
Place Hands Here |
|
Order of Removal (1) |
|
Order of Removal (2) |
|
Remove in this Direction |
Detach the clip as shown in the illustration.
|
Remove in this Direction |
Detach the guide and remove the rear door trim board sub-assembly RH as shown in the illustration.
| *1 | Rear Door Inside Looking Cable Assembly RH |
| *2 | Rear Door Lock Remote Control Cable Assembly RH |
|
Remove in this Direction |
Detach the clamp and disconnect the rear door lock remote control cable assembly RH and rear door inside looking cable assembly RH as shown in the illustration.
69205A
11.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY RH
|
Remove in this Direction |
Detach the claw and guide and remove the rear door inside handle sub-assembly RH.
68173B
12.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP RH
|
Remove in this Direction |
Raise the claw of the rear door inner glass weatherstrip RH as shown in the illustration, and then remove the rear door inner glass weatherstrip RH from the rear door trim board sub-assembly RH.
86160B
13.REMOVE REAR SPEAKER ASSEMBLY
67841E
14.REMOVE REAR DOOR SERVICE HOLE COVER RH
|
Butyl Tape |
Pull out the rear door lock remote control cable assembly RH, rear door inside locking cable assembly RH and wire harness from the rear door service hole cover RH, and then remove the rear door service hole cover RH.
Remove any remaining butyl tape from the rear door panel.
15.REMOVE SCREW GROMMET
Using a clip remover, detach the claw and remove the 2 screw grommets.
68142C
16.REMOVE REAR DOOR GLASS RUN RH
Detach the guide and remove the rear door glass run RH.
67407E
17.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY RH
|
Bolt |
|
Screw |
Lift up the rear door weatherstrip RH and remove the screw.
Remove the 2 bolts and rear door window division bar sub-assembly RH.
68103
18.REMOVE REAR DOOR GLASS SUB-ASSEMBLY RH
Remove the rear door glass sub-assembly RH from the rear door window regulator sub-assembly RH as shown in the illustration.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the rear door glass sub-assembly RH as indicated by the arrows in the order shown in the illustration.
Be careful not to damage the rear door glass sub-assembly RH.
68123B
19.REMOVE REAR DOOR QUARTER WINDOW GLASS RH
|
Remove in this Direction |
Remove the rear door quarter window glass RH together with the rear door quarter window weatherstrip RH.
68188
20.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP RH
Remove the rear door quarter window weatherstrip RH from the rear door quarter window glass RH.
75723
21.REMOVE REAR DOOR REAR BELT MOULDING RH
The procedure described below is for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>REMOVAL
75730
22.REMOVE REAR DOOR BELT MOULDING ASSEMBLY RH
The procedure described below is for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>REMOVAL
69803
23.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH
|
Bolt |
|
Connector |
|
Temporarily Bolt |
Disconnect the connector.
Loosen the temporarily bolt.
Do not remove the temporarily bolt. If the temporarily bolt is removed, the rear door window regulator sub-assembly RH may fall and become damaged.
Remove the 4 bolts and rear door window regulator sub-assembly RH.
85710F
24.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
67836
25.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER RH
Remove the rear door lock child protection cover RH.
69330
26.REMOVE REAR DOOR LOCK ASSEMBLY RH
69037
27.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY RH
69730D
28.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH
69770B
29.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY RH
69318D
30.REMOVE DOOR LOCK WIRING HARNESS SEAL
69227M
31.REMOVE REAR DOOR OUTSIDE HANDLE COVER
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the claw and remove the rear door outside handle cover as shown in the illustration.
69230
32.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY RH
|
Remove in this Direction |
Remove the rear door outside handle assembly RH as shown in the illustration.
69241G
33.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
|
Remove in this Direction |
Detach the claw and remove the rear door front outside handle pad.
69242G
34.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
|
Remove in this Direction |
Detach the claw and remove the rear door rear outside handle pad.
69203A
35.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY RH
| *a | Grommet |
| *b | Guide |
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Detach the grommet and guide and remove the rear door outside handle frame sub-assembly RH.
67003C
36.REMOVE REAR DOOR PANEL CUSHION
Detach the claw and remove the 2 rear door panel cushions.
68630D
37.REMOVE REAR DOOR CHECK ASSEMBLY RH
|
Bolt (A) |
|
Bolt (B) |
Remove the 2 bolts (A), bolt (B) and rear door check assembly RH.
67871
38.REMOVE REAR DOOR WEATHERSTRIP RH
|
Double-sided Tape |
Using a clip remover, detach the clip and remove the rear door weatherstrip RH.
Remove any remaining double-sided tape from the rear door panel RH.
67837C
39.REMOVE REAR DOOR DUST PROOF SEAL
Detach the claw and remove the 3 rear door dust proof seals.
75923C
40.REMOVE NO. 2 BLACK OUT TAPE RH
The procedure described below is for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>REMOVAL
75925C
41.REMOVE NO. 3 BLACK OUT TAPE RH
The procedure described below is for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Rear Door)>REMOVAL